Installation Guide Preface The information provided in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice.
Installation Guide English Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.
Installation Guide Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo Sie das Produkt erworben haben. Italiano/Italian INFORMAZIONE AGLI UTENTI Ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n.
Installation Guide Português/Portuguese Eliminação do seu antigo aparelho 1. Quando este símbolo de latão cruzado estiver afi xado a um produto, signifi ca que o produto é abrangido pela Directiva Europeia 2002/96/EC. 2. Todos os produtos eléctricos e electrónicos devem ser eliminados separadamente da coleta de lixo municipal através de pontos de recolha designados, facilitados pelo governo ou autoridades locais. 3.
Installation Guide Cautions • Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. • Do not disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. • Do not block cooling holes on the bracket This camera has a cooling fan inside.
Installation Guide Table of Contents 1. Introduction ........................................................................................................................... 8 2. Package Content ................................................................................................................. 10 3. PTZ Camera Setups and Cable Connections .................................................................... 12 3.1 3.2 3.3 3.4 3.5 4. PTZ Camera Installation..........................
Installation Guide 6. System Integration .............................................................................................................. 68 6.1 6.2 Using Pelco Keyboard .....................................................................................68 Using Phillips Allegiant Keyboard ....................................................................70 Appendix A: Technical Specification.........................................................................................
Installation Guide 1. Introduction ZC-PT series integrated indoor PTZ Camera is a new subcompact designed to deliver superb performance and durability with an intelligent and stylish housing that is suitable in any security and surveillance installation. ZC-PT-XT series is a new weather resistant integrated outdoor PTZ Camera.
Installation Guide Connect the PTZ Camera to other devices as shown in the diagram to complete a video surveillance solution. NOTE: To extend the network distance up to 1.2 km (4000 feet) and to protect the connected devices, it is highly recommended to place a repeater at the mid-point. However, a repeater may be needed in the network distance less than 1.2 km if the used cables are not the CAT 5, 24-gauge cables (see 3.4.4 RS-485 Connector Definition).
Installation Guide 2. Package Content Before proceeding, please check the box contains the items listed here. If any item is missing, or if damage is evident, DO NOT install or operate the product and contact your dealer for assistance.
Installation Guide Outdoor PTZ Camera Standard Package Camera Body with Screws Outdoor Mount Kit Lubricant Security screw Water-proof rubber set Cable for Power, Video, RS-485 Power Cord Installation Guide & Quick Guide and Alarm CD 11
Installation Guide 3. PTZ Camera Setups and Cable Connections Before installing or connecting the PTZ Camera, please refer to this section and complete preparations for camera setups and various switch setting. 3.1 Preparations for PTZ Camera Setups (Indoor Camera) There will be a PE cloth sheet covered inside the camera cover and a lens cap on the lens for shipping protection. Follow the steps below to remove those protective materials.
Installation Guide STEP 3 Remove the protective cover and PE cloth. STEP 4 Attach the camera cover to the camera body. Before doing that, apply some lubricant on the cover’s water-proof rubber to make the installation process smoother. Note that the tiny protrusion on the camera cover must align with one of the four holes on the camera body. STEP 5 Gently pressure the camera cover downward with two hands on the side of it.
Installation Guide STEP 6 Screw the camera cover and body together. STEP 7 Set the switches located on the bottom of the camera body. Refer to section 3.3 PTZ Camera Setups for detailed information about various switch setting.
Installation Guide 3.3 PTZ Camera Setups Before connecting the camera to other devices of CCTV system, please complete the camera ID and communication switch setting. These switches are located on the bottom of the camera. 3.3.1 Switch Definition Please refer to the following figures and table for switch location and definitions. Indoor PTZ Camera 3.3.
Installation Guide RS-485 is the interface that communicates the PTZ Camera and its control device; for this reason, the RS-485 setup of the PTZ Camera and the control device must be the same. The RS-485 default setting is half-duplex (see the diagram follows). Please do not change the default setting without qualified specialist or supplier’s notice. As for the SW 3 and SW 4, they are used for termination and Line Lock adjustment respectively.
Installation Guide baud rate. Refer to below table and turn the arrow to choose a protocol for your camera. Switch No.
Installation Guide 3.4 Cables and Connections The PTZ Camera is supplied with one integrated 22-pin Data Cable for connecting with the power, video, and RS-485/audio input & audio output cables. Please read the following sections thoroughly before making connections. 3.4.1 Cable Requirements For operation, the PTZ Camera requires video, RS-485 and power cables as described below: • The video cable sends video signals to a remote viewing site. Using a coaxial cable to send video signals is recommended.
Installation Guide 3.4.3 22-Pin Connector Definition With the 22-pin connector, installers can simply connect the power, video and RS-485 cables to the camera at once. For the definition of each pin, please refer to the list below.
Installation Guide 3.4.4 RS-485 Connector Definition RS-485 is the interface that communicates the camera and its control device. Please connect the control keyboard to the speed dome through the terminal block. The recommended cables for RS-485 communication are CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet (1219 meters). If the total cable length exceeds 4000 feet, using a repeater to maintain the signals is recommended.
Installation Guide 3.5 Cable Wiring and Connection Users may need to conduct cable wiring when: (1) Connecting self-provided cords to the connector housing (shown in the figure below) instead of using the equipped data cable or (2) Connecting alarm input and output devices. The table follows will illustrate the way to wire cords into the connector housing. Please refer to the section 3.4.3 22-Pin Connector Definition for the exact position of each cord.
Installation Guide 4. PTZ Camera Installation Basing on different installation environments, both of the Indoor and Outdoor PTZ Camera can be installed on ceiling, on wall or on pole. In the following sections, various installation accessories, installation methods and installation procedures will be described in detail. 4.1 PTZ Camera Dimension The indoor PTZ camera’s dimensions are Ø131 x 226 mm (5.2 x 8.9 Inches). The outdoor camera’s dimensions are Ø172 x 302.5 mm (6.7x11.9 Inches) and Ø190 x 302.
Installation Guide 4.2 Optional Accessories Indoor PTZ Camera Accessories Transparent Cover/Smoke Cover (ZCA-CB-5.4/SB-5.4) Diameter: 137 mm (5.4 inches) 5.4’’ Transparent Cover 5.4’’ Smoke Cover Power Adapter ZCA-100-1.5A Input: 100~115VAC/Output: 24VAC 36VA ZCA-220-1.5A Input: 220~230VAC/Output: 24VAC 36VA NOTE: When wiring, make sure the G/Y wire (Ground) inserted into the mid-pin of the terminal block.
Installation Guide Power Adapter ZCA-100-3.0A Input: 100~115VAC/Output: 24VAC 72VA ZCA-220-3.0A Input: 220~230VAC/Output: 24VAC 72VA NOTE: When wiring, make sure the G/Y wire (Ground) inserted into the mid-pin of the terminal block. Mounting Accessories Hard Ceiling Mount (ZCA-HC200) / Indoor Camera For Hard Ceiling use. Height: 21.4mm ; Diameter of the three holes: 4.
Installation Guide T-Bar Ceiling Mount (ZCA-TB200) / Indoor Camera For in-ceiling Installation use. Height: 170 mm (6.7 inches); Diameter: 180 mm (7.1 inches); 0.5 kg (1.1 lbs) Ceiling Panel For ceiling mounting. Zn platted; 610×305 mm (24×12 inches); Diameter: 135 mm (5.3 inches) Standard Pendent Mount White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs); Diameter: 45 mm (1.8 inches). Supplied with rubber washer-8×1, pendent tube washer×1, spring washer-8×1 and M8*12 screw×1.
Installation Guide Mini Pendent Mount (ZCA-GT100) / Indoor/Outdoor White; 184×104×115.2 mm (7.24×4.09×4.54 inches) Supplied with rubber washer-8×1, pendent tube washer×1, spring washer-8×1 and M8*12 screw×1. Straight Tube (ZCA-ST25,ST50) / Indoor/Outdoor White; Iron; Height: 250/500 mm (9.8/19.7 inches); Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs). Supplied with rubber washer-8×1, pendant tube washer×1, spring waher-8×1 and waterproof rubber×1, M8*12 screw×1.
Installation Guide Pole Mount Adapter (ZCMA-PMA-H/ ZCMA-PMA-Q) White; Height: 51mm (2 inches); Diameter: 52mm (2.04 inches); Thread size:1 1/2” (ZCMA-PMA-H), 1 1/4” (ZCMA-PMA-Q) ZCMA-PMA-H ZCMA-PMA-Q Corner Standard Mounting Plate (ZCA-CST) / Indoor/Outdoor White; 222(L)×204(W)×117(D) mm (8.7×8×4.6 inches); 2 kg (4.4 lbs). Supplied with washer-8×4, spring washer×4, M8*20 screw×4, M8 nut×4. Pole Thin Direct Mounting(ZCA-PTDM) / Indoor/Outdoor White; 232(L)×136(W)×60(D) mm (9.1×5.4×2.
Installation Guide Pole Wide Direct Mounting (ZCA-PWDM) / Indoor/Outdoor White; 270(L)×170(W)×60(D) mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches); 1 kg (2.2 lbs). Supplied with stainless steel straps×4, M8*16 screw×4, washer×4, spring washer×4 Corner Thin Box (ZCA-CTB) ) / Indoor/Outdoor White, 300(L)×164(W)×222(D) mm (11.8×6.5×8.7 inches); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4.
Installation Guide Pole Thin Box (ZCA-PTB) ) / Indoor/Outdoor White; 291(L)×170(W)×250(D) mm (11.5×5.3×9.5 inches); 3.1 kg (6.9 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Pole Wide Box (ZCA-PWB) ) / Indoor/Outdoor White, 270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Wall Box Mounting (ZCA-WBM) ) / Indoor/Outdoor White, 270(L)×166(W)×95(D) mm (10.6×6.5×3.
Installation Guide Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Width: 0.63”; 0.02 kg (0.04 lbs) Stainless Strap Cutter For tension, cut and crimp stainless steel straps. 1.4 kg (3.1 lbs) Suitable for straps width: 1/2”, 5/8”, 3/4” Other Application Accessories Repeater/Converter ZCA-RS422-485: RS-485/RS-232 Repeater ZCA-RS232-485: RS-232 between RS-485/RS-422 ZCA-BP-485: Bi-phase to RS-485/RS-422 ZCA-RS422-485 ZCA-RS232-485 ZCA-BP-485 Power Box White, 186.5×147 mm (7.
Installation Guide RS485 Distribution Unit (ZCA-DS4/8/16) Relay control codes to speed dome cameras. Dimension: 432×44×90 mm (17×17.32×35.43 inches) 4.3 Ceiling Mount Generally, there are three kinds of ceiling mounting methods: hard-ceiling, in-ceiling and mounting with straight tube. Refer to the following sections for more detailed information. The following figures show how cables connect to the camera in different ways.
Installation Guide 4.3.1 Hard-Ceiling Mounting / Indoor Hard Ceiling Mounting is a standard way of installation for Indoor PTZ Camera, and general mounting accessories are equipped in the standard indoor PTZ Camera package. Here lists the items and tools needed to mount the Camera onto the ceilings. The supplied items are all in the PTZ Camera package.
Installation Guide STEP 3 Attach the Mount to the ceiling. Mark the locations where all three ceiling holes should go. STEP 4 Drill these holes on the hard ceiling. STEP 5 Fix the Mount to the holes on the hard ceiling with three screws. STEP 6 Thread the data cable through the center hole of the Mount and connect the cable to the PTZ Camera. STEP 7 Attach the PTZ Camera to the Mount and rotate it clockwise. Tighten the fixing screw to fix the PTZ Camera.
Installation Guide STEP 8 Fix the decoration ring to the bracket. NOTE: Make sure the optical cover is removed before carrying out procedure. STEP 9 Place the optical cover back.
Installation Guide 4.3.2 In-Ceiling Mounting / Indoor Follow the steps to install the PTZ Camera with T-Bar Ceiling mount (ZCA-TB200) accessory for In-Ceiling Mounting. Here lists the items and tools needed to mount the PTZ Camera into the ceilings. The supplied items are all in the standard PTZ Camera package.
Installation Guide STEP 3 Place the Red Sticker on the ceiling plate, and cut the circle part out of the ceiling. STEP 4 Put up the T-Bar into the ceiling opening. STEP 5 Rotate T-Bar wings of the hinge to fix the T-Bar at the edge of the ceiling opening. STEP 6 Tighten the screws, and the T-Bar wings will adhere to the ceiling. STEP 7 Put the cable through the center hole of the T-bar and connect it to the PTZ Camera.
Installation Guide STEP 8 Mount the PTZ Camera to the Bracket and rotate it clockwise. Tighten the fixing screw to fix the Camera. STEP 9 Fix the decoration ring to the bracket and then place the optical cover. NOTE: Make sure the optical cover is removed before carrying out the procedure. 4.3.3 In-Ceiling Mounting with Ceiling Panel To mount the PTZ camera to a suspended ceiling with the T-Bar, the ceiling panel could be employed, as shown in the figure below.
Installation Guide 4.3.4 Ceiling Mounting with Straight Tube (ZCA-ST25/ST50) The straight tube is available in different length: 25 cm and 30 cm. Procedures of mounting the indoor and outdoor cameras with the straight tube will be described respectively as follows.
Installation Guide 7) Fix the plate onto the PTZ Camera’s back plate with the supplied small screw, as marked in the figure. 8) Connect the cables to the PTZ Camera. 9) Mount the PTZ Camera to the Indoor Mount Kit. (Ensure the PTZ Camera is fixed completely, and the thread holes on the Lock Screw Plate and Indoor Mount Kit are aligned). Afterwards, screw the supplied M5 standard screw / security screw, as shown in the picture.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Straight Tube and other equipped items (optional accessory) • Waterproof Rubber (supplied) • Screws and Screw Anchors for fixing the straight tube onto the ceiling (not supplied) Tools Needed • Tool for drilling • Tool for screwing Follow the steps to mount the camera with the Straight Tube.
Installation Guide Ceiling Mounting: Straight Tube + Outdoor Mount Kit 4.4 Wall Mount The PTZ Camera can be mounted on the wall with Mini Pendent Mount, Standard Pendent Mount and Wall Box. Please follow the installation instructions below for mounting the PTZ Camera via different ways. 4.4.
Installation Guide Follow the steps below to mount the PTZ Camera with the Mini Pendent Mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, users could push up the Cable Entry Board on the Mini Pendent Mount’s Mounting Plate to place the cables, as shown in the photo below. Mounting Plate Cable Entry Board 2) Fix the Mini Pendent Mount on the wall with proper screws and screw anchors. 3) Attach the Waterproof Rubber to the Mini Pendent Mount.
Installation Guide Wall Mounting: Mini Pendent Mount + Indoor Mount Kit Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Mini Pendent Mount and equipped items (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Screws and Screw Anchors for fixing the Mini Pendent Mount (not supplied) Tools Needed • Tool for drilling • Tool for screwing Follow the steps below to mount the PTZ Camera with the
Installation Guide Mounting Plate Cable Entry Board 2) Fix the Mini Pendent Mount on the wall with proper screws and screw anchors. 3) Attach the Waterproof Rubber to the Mini Pendent Mount. 4) Run the cable(s) through the Mini Pendent Mount with the Data Cable’s 22-pin cable coming out of the outlet. NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. The sponge can be placed in two ways as shown in the illustrations below.
Installation Guide Wall Mounting: Mini Pendent Mount + Outdoor Mount Kit 4.4.
Installation Guide 2) Fix the Standard Pendent Mount on the wall with proper screws and screw anchors. 3) Attach the Waterproof Rubber to the Standard Pendent Mount. 4) Run the cable(s) through the Standard Pendent Mount with the Data Cable’s 22-pin cable coming out of the outlet. NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.1 Mini Pendent Mount > Step 4.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard Pendent Mount and equipped items (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Screws and Screw Anchors for fixing the Standard Pendent Mount onto the ceiling (not supplied) Tools Needed • Tool for drilling • Tool for screwing Follow the steps below to mount the Dome Camera with the Standard Pendent Mount.
Installation Guide Wall Mounting: Standard Pendent Mount + Outdoor Mount Kit 4.4.
Installation Guide 2) Fix the Wall Box Mounting on the wall with proper screws and screw anchors. Then run the cable(s) through the hole on the Wall Box Mounting with the Data Cable’s 22-pin cable coming out. 3) Fasten the Standard/Mini Pendent Mount onto the Wall Box Mounting with the supplied screws and washers. Then thread the cable(s) through the Standard/Mini Pendent Mount with the cable(s) coming out of the Pendent Mount’s outlet.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard/Mini Pendent Mount and equipped items (optional accessory) • Wall Box Mounting (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Screws and Screw Anchors for fixing the Wall Box Mounting onto the ceiling (not supplied) Tools Needed • Tool for drilling • Tool for screwing Follow the steps to mount the PTZ Camera
Installation Guide Wall Box Mounting: Wall Box Mounting + Standard/Mini Pendent Mount + Outdoor Mount Kit 4.5 Corner Mount 4.5.
Installation Guide Follow the steps below to mount the PTZ Camera with the Corner Mounting Plate and Standard/Mini Pendent Mount. 1) Make a cable entry hole on the wall to recess the cable(s). 2) Fix the Corner Mounting Plate on the corner of the wall with proper screws and screw anchors. Then run the cable(s) through the hole on the Corner Mounting Plate with the Data Cable’s 22-pin cable coming out.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard/Mini Pendent Mount and equipped items (optional accessory) • Standard/Mini Corner Mounting Plate (herein collectively called “Corner Mounting Plate”; optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Screws and Screw Anchors for fixing the Corner Mounting Plate (not supplied) Tools Needed • Tool for drilling • Too
Installation Guide Corner Wall Mounting: Corner Standard/Mini Mounting Plate + Standard/Compact Pendent Mount + Outdoor Mount Kit 4.5.
Installation Guide 2) Fix the Corner Thin/Wide Box on the corner of the wall with proper screws and screw anchors. Then run the cable(s) through the hole on the Corner Mounting Plate with the Data Cable’s 22-pin cable coming out. 3) Fasten the Standard/Mini Pendent Mount onto the Corner Thin/Wide Box with the supplied screws and washers. Then thread the cable(s) through the Standard/Mini Pendent Mount with the cable(s) coming out of the Pendent Mount’s outlet.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard/Compact Pendent Mount and equipped items (optional accessory) • Corner Thin/Wide Box (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Screws and Screw Anchors for fixing the Corner Thin/Wide Box (not supplied) Tools Needed • Tool for drilling • Tool for screwing Follow the steps below to mount the PTZ Camera wi
Installation Guide Corner Box Mounting: Corner Thin/Wide Box + Standard/Mini Pendent Mount + Outdoor Mount Kit 4.6 Pole Mount 4.6.
Installation Guide Follow the steps below to mount the PTZ Camera with the Pole Thin/Wide Direct Mounting and Standard/Mini Pendent Mount. 1) Fasten the Pole Thin/Wide Direct Mounting on a pole with equipped stainless straps. 2) Run the cable(s) through the hole on the Pole Thin/Wide Direct Mounting with the Data Cable’s 22-pin cable coming out. 3) Fasten the Standard/Mini Pendent Mount onto the Pole Thin/Wide Direct Mounting with the supplied screws and washers.
Installation Guide Outdoor PTZ Camera: Items Needed • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard/Mini Pendent Mount and equipped items (optional accessory) • Pole Thin/Wide Direct Mounting (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Stainless Steel Straps for fixing the Pole Thin/Wide Direct Mounting (optional accessory) Tools Needed • Stainless Strap Cutter • Tool for screwing Follow the steps below
Installation Guide Pole Direct Mounting: Pole Thin/Wide Direct Mounting + Standard/Mini Pendent Mount + Outdoor Mount Kit 4.6.
Installation Guide 3) Fasten the Standard/Mini Pendent Mount onto the Pole Thin/Wide Box Mounting with the supplied screws and washers. Then thread the cable(s) through the Standard/Mini Pendent Mount with the cable(s) coming out of the Pendent Mount’s outlet. NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.1 Compact Pendent Mount > Step 4. 4) Attach the Waterproof Rubber to the Standard/Mini Pendent Mount.
Installation Guide Outdoor PTZ Camera: Items Needed: • PTZ Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Standard/Mini Pendent Mount and equipped items (optional accessory) • Pole Thin/Wide Box Mounting (optional accessory) • Waterproof Rubber (supplied) • M5 Standard/Security Screw (supplied) • Stainless Steel Straps for fixing the Pole Thin/Wide Box Mounting (optional accessory) Tools Needed: • Stainless Strap Cutter • Tool for screwing Follow the steps below to m
Installation Guide Pole Box Mounting: Pole Thin/Wide Box + Standard/Mini Pendent Mount + Outdoor Mount Kit 63
Installation Guide 5. System Expansion 5.1 Connecting with Connector Box (Indoor Use) Ideally being used in indoor installation circumstances, a Connector Box provides easy wiring and well organized connection between alarms, cameras and other devices, for easy installation. To connect the connector box with other devices: • Use a RS 485 cable (CAT 5 is recommended) to complete RS 485 communication wiring with control devices such as DVRs and Control Keyboards.
Installation Guide 5.2 Connecting with Power Box A power box contains a 24V AC adapter, two terminal blocks (for communication and power) and one alarm board. With an IP66 case, the Power Box is ideal for outdoor installation environment. Two models are available: 100~115V AC power input (P1030) and 220~230V AC (P2030). Additionally, users can either connect one camera to one power box and to Internet or to other control devices (DVR, Control Keyboard and monitors), as shown in the diagrams below.
Installation Guide 5.3 Repeater Application To integrate other surveillance devices with the cameras or to extend the distance of communications, users could employ three kinds of repeater/converter, as shown below. With the advanced circuit design, these repeaters/converters offer 1KVrms isolation voltage and surge protection capability. The exiting network can be protected by the repeaters/converters. Up to 10 devices are allowed to connect to one repeater/converter.
Installation Guide 5.4 RS485 Distribution Unit (ZCA-DS4/8/16) The RS-485 Distribution Unit (SDU) is designed to relay control codes to cameras. It is capable of communicating with cameras up to 1 kilometer away. Additionally, the SDU can be installed in either “star” or “daisy chain” configuration with up to 160 cameras (see the diagrams below). Its versatile installation configuration makes an easy integration into expanding surveillance systems.
Installation Guide 6. System Integration The PTZ Camera is allowed to be integrated into other suppliers' surveillance systems with large set of built-in protocols. Refer to the following sections for more information. 6.1 Using Pelco Keyboard The PTZ Camera can be controlled through the Pelco keyboard. Please follow the instructions below to manipulate the camera. Open the OSD <9 5> + hold Press the keys, <9 5> + hold or <7 7> + <7 7> + , to display the OSD menu.
Installation Guide Set Auto Pan To set “Auto Pan”, please enter the OSD and go to the By OSD Auto Pan setting menu. The following Presets allows you to execute Auto Pan quickly. <7 9 ~ 8 2> ***<7 9> + : Auto Pan 1 <8 0> + : Auto Pan 2 <8 1> + : Auto Pan 3 <8 2> + : Auto Pan 4 Cable Length RS-485 is the interface that communicates the PTZ camera and its control device.
Installation Guide 6.2 Using Phillips Allegiant Keyboard The PTZ Camera can be integrated into Philips Allegiant systems through D77R3 repeaters. Please follow the instructions to control the cmera through Philips Allegiant systems. Symbol Definition Command dome cameras to go to specific preset position. Set preset position. Open the OSD + <4 6> + Press the keys, + <4 6> + or <7 7> + <7 7> + , to display the OSD menu.
Installation Guide Set and execute CRUISE + <5 0> + To start recording “Cruise”, press the keys + <5 0> + . + <5 0> + To end recording “Cruise”, press the keys + <5 0> + . To execute “Cruise,” press the key . Set and execute Auto Pan By OSD To set “Auto Pan”, please enter the OSD and go to the Auto Pan setting menu. The following Presets allows you to execute Auto Pan quickly.
Installation Guide Appendix A: Technical Specification Items 18× Model 23× Model 26× Model 35× Model 1/4" EXview 1/4" CCD 1/4" EXview 1/4" CCD - Yes - Yes 18× 23x 26× 35x 530 TVL 540 TVL CAMERA CCD Sensor Progressive Scan Optical Zoom Digital Zoom 1× ~ 12× variable NTSC 380k PAL 440k Effective Pixels Horizontal Resolution 530 TVL 540 TVL Scanning System NTSC / PAL Synchronization Internal / Line Lock 1.
Installation Guide Items 18× Model 23× Model 26× Model Resume after Power loss Yes Zone Title 16 Home Function 35× Model Preset, Sequence, Auto pan, Cruise Auto Flip Digital / Mechanical / Off Digital Slow Shutter On / Off On / Off On / Off On / Off - - - On / Off Motion Detection On / Off On / Off On / Off On / Off Wide Dynamic Range On / Off On / Off On / Off On / Off Day/Night: IR Cut Filter On / Off On / Off On / Off On / Off Image Inverse On / Off On / Off On / O
Installation Guide Items Protocols 18× Model 23× Model 26× Model TCP/IP, UDP, HTTP, FTP, SMTP, ARP, ICMP, DHCP, RTP/RTSP Alarm 4 digital alarm inputs / 1 alarm output Alarm Reaction Preset, Sequence, Auto-Pan, Cruise Security Supported Web Browser 74 User Account and Password Protection Windows – Microsoft Internet Explorer 6.
Installation Guide NEW Items NEW 18× Model NEW 30× Model 36× Model CAMERA CCD Sensor Sony CCD Optical Zoom 18× 30× Digital Zoom Effective Pixels 36× 1~12x variable NTSC 380k 480k 380k 480k 380k 480k PAL 440k 570k 440k 570k 440k 570k 540 TVL 650 TVL 540 TVL 650 TVL 540 TVL 650 TVL Horizontal Resolution Scanning System NTSC / PAL Synchronization Internal / Line Lock Video Output 1.0 Vp-p / 75 Ω, BNC S/N Ratio > 50 dB (AGC Off) 0.1 lux 0.1 lux 0.
Installation Guide Home Function Preset, Sequence, Auto pan, Cruise Auto Flip Mechanical/Digital/Off Digital Slow Shutter On/Off Motion Detection On/Off Wide Dynamic Range On/Off Day/Night: IR Cut Filter Auto/Manual Image Freeze On/Off Image Inverse On/Off Noise Reduction 2D On/Off 3D On/Off Alarm Input 8 Alarm Output 1 Alarm Reaction Preset, Sequence, Auto pan, Cruise GENERAL Environment Indoor / Outdoor Controller Interface RS-485 Operating Indoor 0°C ~ 40°C (32°F ~ 104°F)
Installation Guide 77