User Manual
Swivel Hangin
g
Mounting Kit Installation Instructions
For FX5 Electric Heaters
STEP 1
Fasten Angle Hangers (# 1) to a surface or structure that will support
the heater's weight using the installer supplied fasteners. Attach with
the top leg of the angle pointing outwards. (see diagram for orientation)
Note: Installer to supply four 3/8" diameter, grade 5 bolts or
equivalent strength fasteners.
STEP 2
Screw on Connector Hanger (# 2) and one Adapter Hanger (# 3) onto
each steel pipe unitl tight (minimum 5 turns). Pipe lengths will vary
due to angle of support structure.
Note: pipe cut length = distance from support structure to
top of heater less 9 5/8 (241mm)
STEP 3
Bolt the FX5 Mounting Adapters (# 6) to the heater using
1/2"-13 UNC X 1 1/4" bolts (# 7), flat washers(# 9), locking washers (# 10)
and 1/2"-13 UNC nuts (# 8).
STEP 4
Bolt FX5 Bracket, Mounting Attachment (# 5) to the FX5 Mounting
Adapters (# 6) using 1/2" UNC-13 nuts (# 8) and 1/2" locking washers (# 10).
Note: Mtg Attach Assy Bracket (# 3) must be placed with the threaded hole
closet to the control enclosure side of the heater.
STEP 5
Screw the hanger assemblies to the Swivel Mtg Attachment (# 4).
STEP 6
Bolt the 2 pipe assemblies to the Angle Hangers using two
1/2"-13 UNC X 1 1/4" bolts (# 7), flat washers (# 9), locking washers (# 10)
and 1/2"-13 UNC nuts (# 8). Do not place the pipe assemblies on the backside
of the Angle Hanger (# 1).
STEP 7
Lift the heater into place and fasten it to the Swivel MTG Attach Assembly (# 4) using a
5/8"-11 UNC X 1 1/4" bolt (# 9) and 5/8" locking washer (# 10).
Caution: This step will require more than one person due to the weight
of the heater. Refer to the owners manual for the weight of the heater.
Check that you heater model number corresponds to the model number shown on the mounting kit carton.
WARNING
If the heater is installed on a structure that is to be transported, provide additional support
for the heater during transit. The suspended weight should not exceed 250 lbs (114 kg).
Refer to the owner's manual for the mounting specifications and conditions
8
5
4
9
8
6
10
3
7
11
7
10 3/16"
258mm
4 1/2"
(114 mm)
CONTROL
ENCLOSURE
10
12
**SUPPLIED BY CUSTOMER**
FOUR 3/8"
O
, GRADE 5 BOLTS
OR EQUIVALENT STRENGTH
FASTENERS
(NOT SHOWN FOR CLARITY)
2
9
10
8
SUPPORT
STRUCTURE
**SUPPLIED BY CUSTOMER**
( 2 ) 1/2" SCH. 40 OR
HEAVIER STEEL PIPE
THREADED BOTH ENDS
1/2" NPT
1
HEATER
SWIVEL
POINT
ITEM QTY.
1 2
3084
2 2
3085
3 2
4378
4 1
4994
5 1
***
6 2
9771
7 6
2940
8 8
4372
9 6
2941
10 8
4373
11 1
3122
12 1
3093
*** 12" - 9675, 16" - 9677, 20" - 9678
Locking Washer, 1/2" Pltd.
Bolt, 5/8"-11 UNC X 1 1/4", Pltd.
Locking Washer, 5/8" Pltd.
FX5 Mounting Adapter
Bolt, 1/2"-13 UNC X 1 1/4", Pltd.
Nut, 1/2"-13 UNC, Pltd.
Flat Washer, 1/2" Pltd.
Connector Hanger
Adapter Hanger
Swivel Mtg Attach Assy
FX5 Bracket, Mounting Attachment
CONTENTS
CCI
PART
DESCRIPTION
Angle Hanger
Part No. 10478 Printed in CanadaRuffneck™ is a registered trademark of CCI Thermal Technologies Inc.
Copyright© 2007. All rights reserved.
5918 Roper Road
Edmonton, Alberta, T6B 3E1
Canada
Phone: (780) 466-3178
Fax: (780) 468-5904
www.ccithermal.com
1-800-661-8529