Manual

ManualsBrandsCCI Thermal Technologies ManualsAir equipmentXB - Explosion-Proof Natural Convection Heater (Optional Adjustable Temperature Control)

1.0 SPECIAL NOTICES

1.1 The following special notices highlight

important information in the installation and

maintenance sections. Each serves a special

purpose and is displayed in the format shown:

This symbol indicates a potentially hazardous

situation, which, if not avoided, can result in

personal injury or damage to the equipment.

This symbol indicates a potentially hazardous

situation, which, if not avoided, may be a

shock hazard.

This symbol indicates an imminently hazardous

situation, which, if not avoided, could result in

death or serious injury.

2.0 PRE-INSTALLATION

2.1 Initially, inspect the heater for possible

damage due to shipping and handling. Claims

for shipping damages shall be placed with the

carrier.

2.2 Check the heater nameplate to ensure that

the heater area classication and temperature

code are suitable for the hazardous area

classication. For details of hazardous

locations with potential for explosion, refer

to the Canadian Electrical Code or National

Electrical Code.

2.3 Check to ensure that the heater voltage is the

same as the supply voltage.

2.4 The heater must be installed by qualied

personnel in strict compliance with national

and local electrical codes.

WARNING

DO NOT CONNECT THE HEATER TO AN

ELECTRICAL SUPPLY VOLTAGE OTHER

THAN THAT SHOWN ON THE PRODUCT

NAMEPLATE.

3.0 INSTALLATION - GENERAL REQUIREMENTS

3.1 Norseman

XB heaters are approved for wall

or oor mounting with the terminal housing at

the bottom. Ensure that is the wall sufciently

strong to support the heater which, depending

on the model, could weigh up to 100 lbs (45

kg). Otherwise use the brackets supplied to

stand the heater on the oor.

3.2 Do not recess the Norseman

XB heater

into the wall. Use of the brackets supplied will

ensure that the minimum spacing from the

wall of 3.75” (95 mm) is maintained.

3.3 If more than one heater is being installed,

maintain at least 3” (76 mm) between adjacent

heater extrusions. NEVER INSTALL ONE

HEATER ABOVE THE OTHER.

3.4 The Norseman

XB heater relies on natural

convection and “black heat” radiation to transfer

heat to the surroundings. Try to maintain a 12”

(300 mm) clearance and NEVER LESS THAN

6” (150 mm) clearance in front of and at the

sides of the heater.

3.5 Use guard rails in front of the heater if there

is a possibility that moving equipment could

come in contact with the heater.

TYPE XB EXPLOSION-PROOF

CONVECTION PANEL HEATER

INSTALLATION, OPERATION &

MAINTENANCE INSTRUCTIONS

E-mail: info@ccithermal.com www.ccithermal.com

Date of Issue: November 2013

10457.Rev.2.01

Printed In Canada

C US

CAUTION

WARNING

POCC CA. ГБ06.B00913

ISO 9001

Summary of content (8 pages)

PAGE 1
TYPE XB EXPLOSION-PROOF CONVECTION PANEL HEATER INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS 1.0 SPECIAL NOTICES 1.1 CAUTION CAUTION WARNING 2.0 3.0 The following special notices highlight important information in the installation and maintenance sections. Each serves a special purpose and is displayed in the format shown: This symbol indicates a potentially hazardous situation, which, if not avoided, can result in personal injury or damage to the equipment.
PAGE 2
4.0 INSTALLATION - REFLECTOR BAFFLES 4.1 REFLECTOR BAFFLES (T2D units only). Refer to Figure 1 when installing reflector baffles. FIGURE 1 - REFLECTOR BAFFLES INSTALLATION Table 1 - REFLECTOR BAFFLE PAIRS PER HEAT SINK Heat Sink Extrusion Length in Size # of Pairs mm in mm 5.1 130 0 - - 11.8 300 1 8 203 18.5 470 2 8 203 25.2 640 1 24 610 NOTE: Baffles are only required for units with a T2D temperature code rating. FIGURE 2 - DIMENSIONS & MOUNTING DETAILS 4.2 4.3 4.
PAGE 3
5.0 WALL MOUNTING 5.1 6.0 FLOOR MOUNTING Install heater with the supplied hardware in accordance with the Figures and instructions below. Step 1: Position heater face down on the floor with terminal box towards the wall (Figure 6). Step 1: Secure wall and stabilizing brackets to mounting surface (Figure 3). FIGURE 6 - FLOOR MOUNTING DIAGRAM Step 2: Fasten top stabilizing bracket(s) and floor mounting bracket(s) to the unit.
PAGE 4
WARNING 7.0 IMPROPER ORIENTATION OF THE HEATER COULD AFFECT THE SAFE AND RELIABLE OPERATION OF THE HEATER. THERMOSTAT INSTALLATION 7.1 FACTORY INSTALLED - For shipping purposes the thermostat well (located at back of unit) has not been installed. Position thermostat bulb perpendicular to housing being careful not to kink the capillary. Slide well over bulb and screw into place. Make sure that a minimum 5 threads engagement is achieved. 7.2 8.
PAGE 5
WARNING WHENEVER HAZARDOUS MATERIALS ARE PRESENT, ENSURE THAT THE TERMINAL HOUSING COVERS, PLUGS, ETC., ARE SECURED (BUT NOT OVER-TIGHTENED) BEFORE ENERGIZING THE HEATER. CAUTION ALL CIRCUITS MUST BE IN THE OPEN POSITION BEFORE REMOVING JUNCTION OR TERMINAL BOX COVERS. CAUTION USE SUPPLY WIRES SUITABLE FOR 221°F (105°C). SUPPLY WIRES ARE TO BE FUSED WITH APPROPRIATELY SIZED HRC FUSING. WARNING USE APPROVED CONDUIT AND CONDUIT SEALS AS REQUIRED BY HAZARDOUS LOCATION STANDARDS.
PAGE 6
NOTES 6
PAGE 7
NOTES 7
PAGE 8
5918 Roper Road, Edmonton, Alberta, Canada T6B 3E1 Phone: (780) 466-3178 Fax: (780) 468-5904 PLEASE ADHERE TO INSTRUCTIONS PUBLISHED IN THIS MANUAL. Failure to do so may be dangerous and may void certain provisions of your warranty. For further assistance, please call: 24 Hr. Hotline: 1-800-661-8529 (U.S.A. and Canada) Please have model and serial numbers available before calling.