User Manual

Installation
20
|
Installation

Alarm I/O Connection
To connect the alarm input signal
Connect the signal line of an alarm input device such as sensor to the rear [ALARM IN] port.
1.
Loosen the screws on both the alarm input port and [
GND
] port of the provided terminal block plug.
2.
Insert one end of alarm signal cable through the [
AO1
] or [
AO8
] terminal hole below the screw hole, and then fasten
the screw.
3.
Insert the ground signal wire into the hole of the [
GND
] port (shown also below the screw), and tighten the screw.
4.
To check proper insertion of cable, stop pushing and gently pull the cable and test whether it disconnects.
To disconnect a cable, push the bottom side of the terminal and pull out the cable.
To connect the alarm output signal
Connect the signal line of an alarm output device to the rear [
RELAY
] port.
1.
Loosen the screws on the [
NO
] and [
NC
] ports and the [
COM
] port of the provided terminal block plug.
2.
Insert the alarm signal wire into the hole of the [
NO
] or [
NC
] input port (shown below the screw), and tighten the
screw.
Check the relay output type of Normal Open or Normal Close before selecting a proper type (NO or NC).

NO(Normal Open) : Normally Open but switching to Close if an alarm out occurs.

COM : Insert the grounding wire.

NC(Normal Close) : Normally Close but switching to Open if an alarm out occurs.
3.
Insert the ground signal wire into the hole of the [COM] port (shown also below the screw), and tighten the screw.
Or, you can connect the signal cable of the alarm output device to the [ALARM OUT] port on the rear side.
1.
Loosen the screws on the [
AO1
] and [
AO8
] ports and the [
GND
] port of the provided terminal block plug.
2.
Insert the alarm signal wire into the hole of the [
AO1
] or [
AO8
] input port (shown below the screw), and tighten the
screw.
Check the relay output type of Normal Open or Normal Close before selecting a proper type (NO or NC).
3.
Insert the ground signal wire into the hole of the [
GND
] port (shown also below the screw), and tighten the screw.
4.
To check proper insertion of cable, stop pushing and gently pull the cable and test whether it disconnects.
To disconnect a cable, push the bottom side of the terminal and pull out the cable.
5.
Install the wire-connected terminal block in the rear port.
RELAY
NO3
NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7
NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eS ATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
AUDIO IN
ON
OFF
100-240V - 50/60 Hz
SPOT 1
SPOT 2
SPOT 3
SPOT 4
VIDEO IN
LOOP OUT
RELAY
NO3 NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7 NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eS ATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
AUDIO IN
ON
OFF
100-240V - 50/60 Hz
SPOT 1
SPOT 2
SPOT 3
SPOT 4
VIDEO IN
LOOP OUT
RELAY
NO3
NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7
NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eS ATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
ON
OFF
100-240V - 50/60 Hz
SPOT 1
SPOT 2
SPOT 3
SPOT 4
VIDEO IN
LOOP OUT
AUDIO IN
RELAY
NO3 NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7 NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+
D+
D-
D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eS ATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
ON
OFF
100-240V - 50/60 Hz
SPOT 1
SPOT 2
SPOT 3
SPOT 4
VIDEO IN
LOOP OUT
RELAY
NO3
NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7
NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eSATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10
3 / 4 7 / 8 11 / 12
AUDIO OUT
VIDEO IN
LOOP OUT
RELAY
NO3 NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7 NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eSATAUSB HD MONITOR AUX VGA
NTSC
PAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10
3 / 4 7 / 8 11 / 12
AUDIO OUT
VIDEO IN
LOOP OUT
RELAY
NO3
NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7
NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+ D+
D- D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eSATAUSB HD MONITOR AUX VGA
NTSC
PAL
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
AUDIO IN
SPOT 1
SPOT 2
RELAY
NO3 NO1
COM3 COM1
COM4 COM2
NC4 NC2
IN5 IN1
IN6 IN2
GND GND
IN7 IN3
IN8 IN4
GND ARI
ALARM IN
RELAY
NO7 NO5
COM7 COM5
COM8 COM6
NC8 NC6
IN3 IN9
IN14 IN10
GND GND
IN15 IN11
IN16 IN12
GND
PANIC
ALARM IN
RS-485_1
ALARM OUT
RS-485_2
D+
D+
D-
D-
GND GND
RX TX
AO5 AO1
AO6 AO2
GND GND
AO7 AO3
AO8 AO4
RS-232
LAN
(DOWNLINK)
WAN
(UPLINK)
eSATAUSB HD MONITOR AUX VGA
NTSC
PAL
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 / 2
1 / 2 5 / 6 9 / 10 13 / 14
3 / 4 7 / 8 11 / 12 15 / 16
AUDIO OUT
AUDIO IN
SPOT 1
SPOT 2