"EASY SERIES" H.264 Network Digital Video Recorder w/ Internet and Cell Phone Viewing, 320gb Hard Drive and VGA Input USER MANUAL Website: www.CCTVSecurityPros.
CONTENT 1 INTRODUCTION.................................................................................................................. 3 1.1 Main Feature ............................................................................................................................. 3 1.2 Product features.............................................................................................................. 3 1.2.1 Parameter ...............................................................................
1 INTRODUCTION 1.1 Main Feature Our EASY SERIES DVR is developed base on HI3511 hardware platform. EZ SERIES CSPEZDVR4 is 4channel CIF resolution digital video recorder and EZ SERIES-EZDVR8 is 8channnel DVR. Both of them have local recording, playback, support trible code remote network surveillance, data backup, parameter setting, motion detection, I/O alarm setting, PTZ and USB mouse. 1.2 Product features H.264 compression Two USB interface, USB2.0 for data backup, USB1.1 for mouse operation. 3.
Basic electricity output Linearity electricity Record style Audio video recorded simultanously Audio compression ADPCM Picture compression H.
1.2.2 Basic working parameter item parameter remark Voltage input 19V DC 19V。 Voltage outputfor camera 12V（+/-0.2） 12V，1A(For D7704HT) Video impedance input 75Ω 75Ωeach channel。 Video output 1Vp-p 1Vp-p CVBS signal 0—2V Low voltage alarm 5V-30v Hight voltage alarm I/O RS232 serial port, for extend use RS485 Connect to PTZ, (Pelco-D，Pelco-P) SATA HDD One SATA with all capability 1.
2 Device operation manual In device operation, the enter key on remote control has the same function with mouse left click. 2.1 Remote key instruction 2.1.1 Remote control Handheld IR Controller Key Functions: 【0－9】keys：During setup, number keys are used to input values. For viewing channels 1, 2, 3 and 4, use 1, 2, 3 and 4 on numeric keypad respectively. 【＋】,【－】keys：During setup, plus and minus are used to select next or previous values. Website: www.CCTVSecurityPros.
▲， ， ： Up, Down directional keys: Move selection up and down in setup menu. ：Left, Right directional keys: Move cusor left or right in setup menu. 【Enter】key: During setup, select and save entry During Playback and preview, displays the channel name, text number, driver name, event sensor item and time, year/month/date, time, GPRS/GPS info. on the screen. 【PLAY】：Starts/Resumes playback from any other mode (FF, RR, Frame by Frame etc) 【SLOW】：Reduces playback speed to 1/2X、1/4X、1/8X、1/16X mode.
Enter into main menu: Click the right key on the live view. Click right key Exit the present menu: It won’t save the settings if you click the right key to exit. Exit the playback interface: Click the right key to exit when you are playback. Click the left key to enter into the setting interface. Click the left key to zoom in the window on the live view and playback video. Double click the left key can exit to the live view and playback multi-window interface. Click left key 1.
2.1.3 Menu Tree You can control the DVR by a lot of menu operation. This tree will show you the menu structure and it will be in details in after chapter. Website: www.CCTVSecurityPros.
2.2 System Operation 2.2.1 User Login 1. START-UP Connect the DC19V/3A adapter to DVR. When start up the DVR, 【POW】LED will be on and 4 images will be display on the screen. If it has setup ignition recording or time recording, the system will record automatically and the corresponding LED will be on, the system work normally. Remark: If there is no HDD in device, or device didn’t read the HDD, it will display an 【H】in live view. 2.
2.2.2 GUI OPERATION The main menu include “SEARCH”,”RECORD”,”HDD”,”BASIC”， “ADVANCE”,and“Exit”. Remark: You must after pressing “APPLY”to make the setting for submenu valid.It will no use when exit directly.This DVR have a special feature is: when you move the mouse to everwhere, there will have the explanation information showed autoly. 2.2.2.1 RECORD SEARCH Move the cursor to 【RECORD SEARCH】（Icon highlighted when selected）,press【Enter】to enter into the setting interface.
1.MONTH: It will show all the recording status in this month. Green means normal recording, Red means alarm recording, Grounding means no recording. Click any date in this frame can search the recording status of that day,the searching result will be showed in the below date frame. 2. DATE: It will show all the recording status in this day, you can playback the record file in this period via click the corresponding period. PLYBACK:You can press 【Enter】【+】【/-】or input number directly to setup playback time.
【PAUSE/STEP 】to pause and frame by frame play；Press 【Exit】to exit from playback and return to the former menu； 5. When finished playback files, it will return to the file list interface. 2. BACKUP You can use USB for backup，should insert USB device into the USB2.0 port before backup files. And it is support USB OTG.
CHANNEL：ON: Means the channel enable for recording. RESOLUTION：Setup resolution and code rate for recording, there are HIGEST, HIGH, NORMAL three options, corresponding to D1 、HD1、CIF resolution. QUALITY ：There are BEST, FINE ANDNORMAL three option, corresponding HIGHEST, HINGAND NORMAL data stream standard AUDIO：ON: Means enable the audio recording for all channels, OFF: Means disable audio recording REC.MODE： POWER UP: Means the device will start recording when it startup.
means alarm record, green means normal record, grounding means no record. RECORD SIZE：There are 15min, 30min, 45min, 60min four options, that means it will pack as the mode you selected Scroll to APPLY and press ENTER to save the new settings. 2.2.2.3 HDD MANAGE Move the cursor to 【HDD】（Icon highlighted when selected）,press【Enter 】to enter into the setting interface, and you can use direction keys and cursor to change the options. HDD STATUS：There are three status available, normal, un-format, No HDD.
Basic setup includes system language, time/date, security, display, video/audio and exit six options. 2.2.2.4.1 SYSTEM LANGUAGE SETUP Move cursor to select “system language” (The big icon means select ok)and press 【ENTER】to enter into the system language setup interface. System language have Chinese and English two options, you can setup the language you want in here. Remark: The device will restart when you setup system language success. 2.2.2.4.
DATE: Setup system date via numeric key. DATE FORMAT: Press ENTER to switch between the date patterns, there are YY-MM-DD and MM/DD/YY two options. TIME: Setup system time via numeric key. TIME FORMAT: Press ENTER to switch between the date patterns, there are 12 HOURS and 24 HOURS two options. Remark: You must move the cursor to the 【MODIFY TIME AND DATE】 and press 【APPLY】to save it, otherwise it won’t save the modify if you exit this interface. DST: haven’t finished yet. 2.2.2.4.
PASSWORD：Press【APPLY 】to start or close user password. If it is “ENABLE”, you must input password when log in, otherwise, you can enter into main manu directly. USER PASSWORD：Press 【+】/【-】or numbe keys to setup user password. ADMIN PASSWORD：Press【+】/【-】or press number keys to setup admin password. 2.2.2.4.4 DISPLAY SETUP Move the cursor to【DISPLAY SETUP 】（Icon highlighted when selected）, press【Enter 】to enter into the setting interface. NAME: press【Enter】to enter into the setting interface.
PREVIEW：ON: Means the channel is allowed to view the live mode, OFF means not. PREVIEW TIME: ON: Means insert clock in live view, OFF means not. RECORD TIME ：ON: Means insert clock in record file, OFF means not. 2.2.2.4.5 VIDOE/AUDIO SETUP Move the cursor to【VIDEO/AUDIO SETUP】（Icon highlighted when selected），press【Enter 】to enter into setting interface. VGA RESOLUTION：press【Enter】key to setup the VGA resolution, there are 1024*768 、800*600 and 600*480 three options.
Advanced Features include Alarm settings, system information, Motion detection, mobile phone monitoring, system maintenance, PTZ and network setting. 2.2.2.5.1 ALARM SETUP Move the cursor to【ALARM SETUP 】（Icon highlighted when selected），press【Enter】to enter into setting interface. I/O CHANNEL： Each channel corresponds an I/O status, that is, when an alarm triggered, it will activate the corresponding channel to start alarm recording. N.O：indicate I / O input level from high to low effective N.
0 second、10 seconds, 20 seconds, 40 seconds and 60 seconds ● BUZZER：buzzer calling time setup when alarm triggered: 0 second,10 seconds,20 seconds,40 seconds and 60 seconds ● POST REC.：post recording time setup: 30 seconds,1 minute,2 minutes and 5 minutes ● PRE REC：Pre-recording time is fixed as10 seconds. 2.2.2.5.
the motion detection for each channel.. SNESITIVITY：each channel has corresponding sensitivity setting,including four standards high,higher,medium and low, press 【Enter】key to switch MD AREA： each channel has corresponding regional motion detecting setting,move the cursor to corresponding 【setting】，press【Enter】to enter regional setting interface, red area means it have activated motion detection, transparent block means it have not activated motion detection.
CHANNEL: select the channel for mobile view, and press [Enter] to switch different channels. MOBLE NETWORK: Select different mobile network from the options of 3G, 2.5G and 2.75G, and press [Enter] to switch different network. 2.2.2.5.5 SYSTEM MAINTAIN Move the cursor to 【SYSTEM MAINTAIN 】 (Frame turns red means selected), and press 【Enter】to enter into system maintain setup interface. AUTO RESET: When switch is on, you can setup the time for device to restart.
DEFAULT SETTINGS: Restore all the settings as the factory setting. 2.2.2.5.6 PTZ SETUP Move the cursor to【PTZ SETUP 】（Icon highlighted when selected），press【Enter】to enter into setting interface, you can setup the parameters for each channel separately. CHANNEL: The channel of PTZ connected.
Move the cursor to [NETWORK SETUP] (icon thighlitend when selected), and press 【Enter】to enter into setting interface . TYPE: There are PPPOE, DHCP & Static three options. ● STATIC Select [Static] in the type, and press [Enter] to enter into the interface as followings MEDIA PORT：transfers video data between client and device. WEB PORT: setup the port of IE browser via HTTP. IP ADDRESS: setup the IP address, and press [Enter], [+], [-] or number keys to change the value.
PPPOE username and password: fill the username and password of the internet service offer, and apply it and reboot the system. After rebooting, the device will save it and set the PPPOE as default network type. If succeed, the IP address will be automatically config as dynamic IP of WAN. ● PPPOE Select the PPPOE, and enter the interface as followings MEDIA PORT：transfers video data between client and device. WEB PORT: setup the port of IE browser via HTTP.
DDNS: There are [ON/OFF], and if there is a DDNS service, please setup it as ON. SERVICE: There are 3 serviceS to select, 3322, dyndns, perfecteyes. HOST NAME: Input the name of the host server. USERNAME: Input in the name of the user. PASSWORD: Input the password. IE OPERATION 3.1 FEATURE Through the IE browser of OS and install the software, you are able to do the network operation remotely, which is much more convenient.
Remark: If you connect the device in WAN, the IP should be a public IP. 3.3 OPERATION INTERFACE There are Liveview, Playback and Setup options in the main interface, please press them to access it. 3.3.1 LIVE Click to enter into the interface as followings 3.3.1.1 PTZ CONTROL Change the focus, preset aperture to control the PTZ. to up/down/left/right control movement of the PTZ.
3.3.1.1.1 ZOOM Click to zoom in and out. Click to focus Click to change the size of aperture 3.3.1.1.2 PTZ PRESET Setup preset point. You can control it via the below three buttons: 3.3.1.2 PLAY Move cursor to the icons, it will highlighted when selected Open all windows.
3.3.1.3 OTHER OPERATION 1 1. Select one channel at preview screen (the selected channel’s frame will be change to RED), double click left key, enter to the selected channel single screen display. 2 2. Click one Chanel via left key at preview screen, then click right key, will occur window shortcut Menu, see below picture You can open, shut down and start this channel’s record via shortcut menu. 3.
The highlighted date means that day have recording video, RED FRAME means the date is system date, click the date will search that days’ recording file list. For example, the above picture display 2008, Dec. 3 ,4 ,5 ,6 ,8 ,9 ,10 ,11 ,12 ,17 ,18 have rd th th th th th th th th th th th th recording video, and system date is 18 , Dec, 2008, currently search date is 17 , Dec. At the below of calendar select channel and type, click SEARCH, the result will display, as follow.
Slow play Pause at next frame Convert H.264 file to H.avi file, click this button access into file convert setting interface, as follow. SOURCE FILE: Click After setting, click to setup the H.264 file to convert to setup the directory for saving avi file , file convert start, the convert progress bar (see below picture) will see the progress of convert. Website: www.CCTVSecurityPros.
3.3.3 SETUP Click to enter into setup interface, this interface include record, alarm, PTZ, network, setting and system information six menus. 3.3.3.1 RECORD Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. 3.3.3.2 ALARM Click as in GUI of DVR. to enter into setup interface; you can check the parameter settings Website: www.CCTVSecurityPros.
3.3.3.3 PTZ Click as in GUI of DVR. to enter into setup interface; you can check the parameter settings Website: www.CCTVSecurityPros.
3.3.3.4 NETWORK Click to enter into setup interface; you can check the parameter settings as in GUI of DVR. 3.3.3.5 SETTING Click as in GUI of DVR. to enter into setup interface; you can check the parameter settings Website: www.CCTVSecurityPros.
BANDWIDTH: Set the amount of bandwidth in kbps (128k、192k 、256k、384k 、512k、1024k) that you want to allocate for traffic that matches internet，this bandwidth not includes audio. FILE SAVE PATH: capture picture and recording video save path. IE login password and DST settings you can check as DVR setting. 3.3.3.6 HOST INFO Click to enter into system information interface (see below picture), this interface shows HDD status, remain record time, firmware version, MAC Address, and all the information is fixed.
4 DVR Installation Guideline 4.1 Product Overview 1 2 Product Photo The Definition of Bottons and Connectors on Front Panel Website: www.CCTVSecurityPros.
Buttons on Front Panel ＃ Button Name Description 1 Power STANDBY POWER/OFF, boot up DVR or shutdown DVR Navigation During the setting for GUI, use these bottons for choosing differents items on menu. And also control the direction of PTZ.
Item Connector description Physical connector 1 DC 19V/3A POWER input 2 Video output 3 Two video output for connecting TV or monitor (BNC) For connectiong analog video signal input (BNC) Video input 4 For connecting aidio signal Audio Input 5 I/O alarm input, 4 for 4CH DVR and 8 for 8CH DVR Alarm Input I/O output for alarm Alarm Output RS485 RS 485 for connecting PTZ RS232 For connecting PC +12V Power supply for DC relay and the current is 100MA (make sure short circiut can not happen) 6 Ne
There are 8 sets alarm input connector and 1 set output for this DVR. Alarm input is for connection IR annunciator, fog sensor. The connection diagram of DC alarm inout as following: Connection diagram of AC alarm input as following: The connection diagram of alarm output as following: Website: www.CCTVSecurityPros.
6. System Network Diagram 4.2 HDD Installation Please installation the HDD as the following steps: 1）Uninstall the DVR and then you will see one HDD plate as following. Website: www.CCTVSecurityPros.
2）Take out the anti-vibration mat and screws from the accessories box 3）Take off the HDD plate and then install the anti-vibration mat on the plate and then screw on it. 4）Install the HDD on HDD plate as the following photo indicate and then screws around. Website: www.CCTVSecurityPros.
5）Fix the HDD plate on the DVR device and then cover the DVR and screw. Remark: Please format the new HDD before record. Website: www.CCTVSecurityPros.
