ECA & EVA Extractors Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative consequences for the environment and health. It also enables the constituent materials to be recovered, saving both energy and resources.
• Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters. Note: For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking.
Using Your Extractor (ECA Range) Control Panel A - Light button B - Speed level buttons C - Power off button Fig. 1 A B C To switch the extractor light on or off: • Press button “A”. To switch on the extractor or to change the speed at any time when the extractor is running: • Press the relevant “B” button for the first, second or third speed level as required. To switch the extractor off: • Press button “C”.
Using Your Extractor (EVA Range) Control Panel A - Speed level keys B - Light key C - Off key Fig. 2 A B C To switch on the extractor or to change the speed at any time when the extractor is running: • Touch the relevant key “A” for the first, second or third speed level as required. To switch the extractor light on or off: • Touch key “B”. To switch the extractor off: • Touch key “C” twice. To activate the “Timer” mode: • Touch key “C” once when the extractor is already running.
Care and Maintenance IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth, for example the CDA E-Cloth. Fig. 3 Fig.
To remove the grease filter • Open the hinged panel as shown in Fig. 3. • Push in the button on the handle and then pull down on the filter at the top as shown in Fig. 4. • When you have released it at the top, then you can pull the filter out completely. After rinsing and drying, reassemble the grease filter to the hood by reversing the removal process. Please note: Cleaning the grease filter in the dishwasher may lead to discolouration.
The LED Lights The light bulbs are high efficiency 3V 3W LEDs. These lights are designed to last for the lifetime of the product and are not user-replaceable. In the unlikely event of a problem with these lights contact CDA Customer Care for assistance. The lights are designed for use during cooking and not for general room illumination. Extended use of the lights can reduce the life span of the LED bulbs.
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations.
Assembly and electrical connection should be carried out by specialised personnel. When installing this product we recommend you seek the help of another individual. Electrical Information Mains electrical voltage: 230 – 240Vac Total rated power consumption: 126W If your extractor is not working: 1. Check that the mains supply has not been switched off. 2. Check that the fuse in the spur has not blown.
Mounting Your Extractor Your extractor can be used to filter and recycle the air within your kitchen, or to extract the air outside. D B When installing this appliance over a CDA hob, the clearance between the extractor and the hob must be equal to or exceed 550mm. This instruction overrides the instructions supplied with the CDA hob. (The height should be measured from the top of the hotplates or burners).
Installation The metal casing of this appliance has been coated with a preservative to protect it during transport and storage. This should be removed during installation by using a non-abrasive stainless steel cleaner. Always follow the instructions given with the cleaner being used. When correctly installed, your product meets all safety requirements laid down for this type of product.
Mark wall required (see Fig.5) Mark out as wall as required, see Fig 9. Tools required. Tools required 8 Fig. 8 Fig. 7 Fig. 8 Drill six mounting holes. Fit wall fixings and top screws. Fit wallthat fixings and top screws Ensure Ensure any fixings you -use are appropriate for you theuse wallaretype. that any fixings appropriate Drill 6 holes for mounting the body for the wall type. Fig. 9 Fig. 9 Fig. 10 Fig.
FitFitthe ducting adaptor. ducting adaptor Fix ducting and seal joints. Fix ducting (seal joint) Fig. 12 Fig. 11 Fig. 11 Mount the chimney. Mount the lower chimney Fig.Fig. 13 13 Fig. 12 Adjust and secure the chimney. Adjust and secure the upper chimney Fig. Fig.
NOTES 16
NOTES 17
NOTES 18
Energy Efficiency Information Attribute Model Identification Symbol ECA60 Value EVA60 & EVA90 61.6 Units Annual Energy Consumption AECHood 61.6 Time increase factor Fluid Dynamic Efficiency f FDEHood 1.7 9.2 1.7 9.2 Energy Efficiency Index EEIHood 87.6 87.6 Measured airflow at Best Efficiency Point Measured Pressure at Best Efficiency Point Maximum airflow QBEP 207.3 207.3 m /h PBEP 151 151 Pa QMAX 329.6 329.6 WBEP 94.1 94.
Please contact our Customer Care Department for Service on the details below Customer Care Department The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu Copyright © CDA 2014 www.cda.
