ECH/CPX/ECN Extractors Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A – Power indicator light B – Light button C – Power off button D – Speed level buttons Fig. 1 To switch the extractor light on or off • Press button B.
Care and Maintenance IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth, for example the CDA E-Cloth.
Changing the Light DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. Remove the grease filter, unscrew the light bulb and replace the light with the required light bulb as shown below. Finally, replace the grease filter. ECH 40W max candle bulb SES (screw type) CPX 50W max halogen 2 pin GU10 ECN 50W max halogen 2 pin GU10 Table 1 Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights.
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations.
Electrical Information Mains electrical voltage: 230 – 240Vac Total rated power consumption: ECH: 220W CPX: 240W ECN: 240W Troubleshooting Please note: Your extractor is equipped with a motor protection device that will switch off the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/burners are being used simultaneously, or if your extractor is installed incorrectly, lower than the recommended height.
Mounting your Extractor When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must exceed 600mm (650mm is recommended). When the extractor is to be installed above a gas hob, the minimum distance between the hob and extractor must exceed 700mm (750mm is recommended).
INSTALLATION Tools required Figu wall re 2as required - M ar k (see wal table l as 2) req ui red (see ta bl e 1) Mark Fig. 6 Fig. 7 Drill holes Figu re 3 - D rill h oles Fit wall fixings and top screws - Ensure that any fixings you use are appropriate for the wall type. Fig. 8 Fig. 9 Figu re 5 - (tighten Se cur eallhoo d (tigh ten all scr ews) Secure hood screws) Figu re 6 - Fi t duc tin g adap tor Fig. 10 Fig.
Figu re 7 - Mo unt chimne y bracke ts Mount chimney brackets Fix ducting Figu (seal re 8 joint) - Fix ducting (s ea l joint) Fig. 12 Fig. 13 re 9 - Mo unt the chim ne y MountFigu the chimney Adjust and secure the chimney Fig. 14 Fig.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
