FF820 Freestanding Full Height Larder Fridge Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
CE Declarations of Conformity: This appliance has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (Low voltage) and requirements of EMC Directive 2004/108/EEC. This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109.
Before First Use You must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior. The fridge may have an odour to it at first use. This will disappear as the appliance cools. Please note: • The appliance will work continuously until it comes down to the correct temperature.
• Do not splash water onto the top or back of this appliance. • Never put liquids in the refrigerator uncovered. • Never put hot foods in the refrigerator. Warm food should be allowed to cool to room temperature before being put into the refrigerator. • Nothing should rest against the internal rear wall of the refrigerator, as this will cause frost and possible condensation problems which will be difficult to remove.
Control Panel A On/Off key B Increase temperature key D C Decrease temperature key D High humidity function key A B C E High humidity indicator fig. 1 Switching the fridge on and off To switch on the fridge for the first time, press and hold the On/Off key (A) for three seconds. The fridge will beep twice, and will run at the factory preset temperature of 5°. To switch the fridge off, press and hold the On/Off key for three seconds.
high humidity indicator will show on the display and the fridge will beep twice to confirm the setting. To switch the high humidity function off, press and hold the high humidity key for three seconds. The high humidity indicator on the display will switch off and the fridge will beep twice to confirm the setting. Please note: The temperature will show on the display for 30 seconds after the door has been opened, or a key has been pressed on the control panel before switching off automatically.
Defrosting the Fridge The fridge is self-defrosting. The defrosted water is collected in the evaporating tray at the back of the appliance. fig. 2 Adjusting the shelves The fridge shelves can be moved according to the storage requirements within the fridge section. To move the shelf, lift up the front section and then pull it outwards. To replace, slide the shelf back into the slot, and the lower the front section. 8 fig.
Care and Cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. • The refrigerator should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • Clean the shelves and balconies separately by hand using soap and water. Do not put them in the dishwasher. • Once cleaning is complete, reconnect the mains power supply.
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. The appliance is not working • Check there is power to the appliance: • The house fuses are intact and the fuse in the plug has not blown. • The thermostat is not set to 0 (off position). • The plug socket is functioning fine. To check this, plug another electrical appliance in to see if the socket is working.
There is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear. Please note: The LED lighting cannot be replaced without a service call. If the light fails, contact CDA Customer Care. Error Codes The display will show error codes if there is a fault with the appliance. These are detailed below. Before calling CDA Customer Care, take note of the error code as this will help when attempting to resolve the problem.
Installation And Ventilation 685 This appliance must never be installed close to heat sources i.e. heating elements, cookers or in damp places 1855 The diagram shows the ventilation requirements for your product. Failure to provide adequate ventilation can lead to increased running costs and premature failure and may invalidate the warranty provided with the product. 595 fig. 4 • Ensure ventilation openings are kept clear. • Do not use a multi-purpose socket alongside other appliances.
Reversing the Door We recommend you seek the help of another individual to support the doors whilst performing this operation. 1. Carefully remove the two hinge cover plates and two cover caps from the control panel. 2. Remove the control panel, ensuring that the wires are not damaged. We recommend you secure the control panel with masking tape to the top of the fridge whilst it is detached. 3. Remove the screws securing the upper hinge whilst supporting the door.
opposite side, leaving the screwhead approximately 3mm proud of the appliance. 6. Remove the lower hinge and reposition the lower hinge pin as shown in figure 5. fig. 7 Lower hinge fig. 8 7. Reposition the lower hinge on the opposite side as shown in fig 7. 8. Reverse the upper hinge pin as shown in fig 6. 9. Locate the door on the lower hinge pin, then locate the upper hinge pin in the door. 10.
Electrical Information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELLOW. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or coloured BLACK.
NOTES 18
NOTES 19
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
