FF880 freestanding full height freezer Manual for Installation, Use and Maintenance Passionate about style 1 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Before First Use You must allow the freezer to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior. The freezer may have an odour to it at first use. This will disappear as the appliance cools.
Control Panel A On/Off key B Increase temperature key D B A C C Decrease temperature key D Quick freeze function key E Quick freeze indicator fig. 1 E Switching the freezer on and off To switch on the freezer for the first time, press and hold the On/Off key (A) for three seconds. The freezer will beep twice, and will run at the factory preset temperature of -18°. To switch the freezer off, press and hold the On/Off key for three seconds.
Super freeze function The super freeze function can be used to freeze large quantities of fresh food as quickly as possible. This function can be set for specific durations before switching off automatically for convenience. To switch on the super freeze function, touch and hold the super freeze function key (D) for approximately three seconds. The super freeze symbol on the display will flash and the freezer temperature display will show 6.
Care and Cleaning Always disconnect the appliance from the power before any cleaning or maintenance. • The refrigerator should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • Clean the shelves and balconies separately by hand using soap and water. Do not put them in the dishwasher. • Once cleaning is complete, reconnect the mains power supply.
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is power to the appliance. • The house fuses are intact and the fuse in the plug has not blown. • The plug socket is functioning fine. To check this, plug another electrical appliance in to see if the socket is working.
Installation and Ventilation This appliance must never be installed close to heat sources i.e. heating elements, cookers or in damp places. 695 The diagram shows the ventilation requirements for your product. Failure to provide adequate ventilation can lead to increased running costs and premature failure and may invalidate the warranty provided with the product. • Ensure ventilation openings are kept clear. • Do not use a multi-purpose socket alongside other appliances.
Reversing the Door We recommend you seek the help of another individual to support the doors whilst performing this operation. fig. 5 Left cover plate Cover cap Right cover plate 1. C arefully remove the two hinge cover plates and two cover caps from the control panel. 2. Remove the control panel, ensuring that the wires are not damaged. We recommend you support the control panel with masking tape on the top of the freezer whilst it is detached. control panel fig. 6 3.
Reversing the door fig. 7 6. R emove the lower hinge and reposition the lower hinge pin as shown in figure 7. 7. R eposition the lower hinge on the opposite side as shown in fig 9. 8. Reverse the upper hinge pin as shown in fig 8. fig. 8 9. L ocate the door on the lower hinge pin, then locate the upper hinge pin in the door. 10. Slot the upper hinge into the locating screw on the appliance and then secure with the two screws removed in step 3. 11.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style 12 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.
