fwc152 / fwc303 / fwc603 / fwc623 Wine Coolers Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
Before first use You must allow the appliance to settle for at least twenty four hours prior to switching the power on. It is recommended that you remove all internal and external packaging and clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly dry the interior. The appliance may have an odour to it at first use. This will disappear as the appliance cools.
Use and Controls fwc152 1 2 4 3 Key: 1 – Power button 2 – Light button 3 – "+" button 4 – "-" button fig. 1 fwc303 1 2 3 4 Key: 1 – Power button 2 – Light button 3 – "+" button 4 – "-" button fig. 2 To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the "+" or "-" buttons until the required temperature is shown on the display. • The preset temperature is 12˚C / 54˚ F.
Use and Controls fwc603 & fwc623 1 2 3 4 5 6 fig. 3 Key: 1 – Power button 2 – Left/Upper zone "+" button 3 – Left/Upper zone "-" button 4 – Right/Lower zone "+" button 5 – Right/Lower zone "-" button 6 – Light button To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the "+" or "-" buttons for the appropriate zone until the required temperature is shown on the display.
Use (All Models) Humidity Control (all models except fwc152) The wine coolers are equipped with a humidity control system to maintain optimal humidity within the wine cooler. Fill the humidity reservoir approximately 3/4 full with water. Place the reservoir over the special lugs toward the back of the top shelf only, as shown in fig. 5. Ensure it is located correctly to prevent water spillage. Check the water level regularly and refill if required. fig.
Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water.
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working.
Installing the Wine Cooler This appliance is intended to be installed in a space between two units.
Installation This appliance is designed to fit under worktops between 820 – 890mm in height, using the adjustable plinth plate to ensure that the feet are concealed from view. Loosen but do not remove the rear ventilation trim screws. Slide the rear plinth to the required height. Tighten the trim screws to lock the plinth in position.
Reversing the Door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Remove the rear ventilation trim (2) by removing screws (1) and then remove the front ventilation trim (4) by removing screws (3) as shown in figure 7. 2. Remove the lower hinge (5) by removing the four screws 6) as shown in figure 8. Support the door as you do this to prevent damage. 3.
Electrical Information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
CDA Brand Model Identifier fwc152ss fwc152bl fwc303ss fwc303bl fwc603ss Category of the Household Refrigerating Appliance 2 230-240V~/50Hz Voltage/Frequency Dimensions (WxDxH cm) fwc623ss 14.8x57x82 29.5x61.5x82 59.5x61.5x82 59.5x61.5x82 Weight (kg) 19 27 45 47 Energy Efficiency Class B A B B 186 139 183 195 Annual Energy Consumption (AEc) (kWh/year) Storage Volume (l) Coldest Storage Temperature (°C) The energy consumption is based on standard test results for 24 hours.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.
