FWV470 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel.
Icemaker Display Control Panel Water Nozzle Ice Drawer Ice Water Tray Drip Tray Icemaker control panel ON 1 OFF 2 3 4 5 6 1. On button 2. Off button 3. Water glass button – this button dispenses a small amount of water. 4. Water jug button – this button dispenses a large amount of water. 5. Manual water button – this button dispenses water as long as the button is pressed. 6. Settings button – this button changes the preset amounts of water.
The Icemaker Before first use: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Turn on the machine at the power switch on the left side of the machine The machine will automatically start a drain cycle, which will take approximately five minutes. During this process, the display will show ICE OFF WATER EMPTY. 3. Push the machine back into the housing. 4. Switch on the machine by pressing the button.
The Icemaker To make ice The icemaker will make ice automatically once it is switched on and will continue to make ice until the ice compartment is full. Whenever ice is removed, the icemaker will make more ice until the compartment is full again. To dispense water The amount of water dispensed from the water nozzle is controlled by three different buttons. – water glass – water jug – manual setting – this button dispenses water as long as the button is pressed.
Care and maintenance Always disconnect the appliance from the power before any cleaning or maintenance. As the icemaker has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Proprietary stainless steel cleaners are available.
Troubleshooting Problem Solution: WATER MISSING shows in the display Check the water supply is connected and switched on ICE FAULT WATER READY shows in the display at first switch on Turn the icemaker off with switching it on again. The dispensed water has an unpleasant taste Ensure that only water pipes suitable for drinking water are used ICE FAULT shows in the display remove some ice and turn it on again. Turn the icemaker off with We recommend that the unit is not left on permanently.
Installation min. 200cm2 IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY QUALIFIED PERSON. 600 We recommend that you seek the assistance of another individual when installing this appliance. This appliance requires a mains water supply and a connection to the drain/ waste system (drain connection is not supplied) 450 min 560 19 392.5 458 1. Slide the base unit into the housing ensuring the dimensions are correct as per figure 1. 2.
7. Connect the drain pipe as shown in fig 6 and the other end to an appropriate drain, for example a laundry standpipe or under sink spigot . Drain connections to the plumbing side are not supplied. 8. Insert the appliance into the housing, ensuring that the runners on the machine are located in the runners on the base unit. Then slide the appliance fully into the housing. i Please note: Due to the weight of this appliance, the housing unit must be secured to the wall prior to installation.
Electrical information Warning! This appliance must be earthed. Green & Yellow to Earth Brown to Live A 13 Amp Fuse B Cord Clamp Blue to Neutral The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
10
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
