FWV451/FWV901/FWV1201 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
Before First Use You must allow the appliance to settle for at least twenty four hours prior to switching the power on. It is recommended that you remove all internal and external packaging and clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly dry the interior. The appliance may have an odour to it at first use. This will disappear as the appliance cools.
Use and Controls FWV451 1 2 3 4 Key: 1 – Power button 2 – Light button 3 – Up button 4 – Down button fig. 1 To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the up or down buttons until the required temperature is shown on the display. • The preset temperature is 12˚C / 54˚ F. • To change the temperature display from Fahrenheit to Celsius, or Celsius to Fahrenheit, press and hold the light button for five seconds.
Use and Controls FWV901/FWV1201 1 2 4 3 fig. 2 7 5 6 8 Key: 1 – Power button 2 – Upper Zone, up button 3 – Upper Zone, down button 4 – Lower Zone, up button 5 – Lower Zone, down button 6 – Light button 7 – Upper Zone 8 – Lower Zone To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the up or down buttons for the appropriate zone until the required temperature is shown on the display.
Use Humidity Control The wine coolers are equipped with a humidity control system to maintain optimal humidity within the wine cooler. Fill the humidity reservoir approximately 3/4 full with water. Place the reservoir on the runners on the top shelf as shown in fig. 5. Ensure it is located correctly to prevent water spillage. Check the water level regularly and refill if required. fig. 3 Temperature display The temperature display will show the current internal temperature.
Door alarm The wine cooler is equipped with an alarm that will sound if the door is left open for more than 60 seconds. To switch . If the temperature has risen beyond the set temperature, the display will flash until the zone has off the alarm, press returned to the required temperature. Interior light The wine cooler has two options for the interior lights. To change from one option to the other, press the • .
Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water.
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working.
Installing the Wine Cooler min. 200cm2 This appliance is intended to be built in to a kitchen cabinet. This appliance should be installed in a well ventilated, dry room. This appliance must not be installed: 1. In direct sunlight 2. Adjacent to a heat source (oven or radiator) 560 - 568 3. Below a hob unit Place your wine cooler in a location which is strong enough to support its weight when fully loaded. To level the wine cooler, adjust the front levelling legs at the bottom of the wine cooler.
Reversing the Door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Remove the glass door by removing the eight screws (3 and 4 in figure 6). Support the door as you do this to prevent damage. 2. Gently remove the door and place on a padded surface to avoid the risk of damage. 3. Unscrew the roller (2) and relocate it on the opposite side. 4. Rotate the door 180º and relocate it on the opposite side. 5.
Electrical Information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
CDA Brand Model Identifier Category of the Household Refrigerating Appliance Voltage/Frequency FWV451SS Dimensions (WxDxH cm) FWV901SS 2 230-240V~/50Hz 59.2x60.8x45.5 59.2x60.8x88.5 Weight (kg) 30 48 Energy Efficiency Class B B 190 195 Annual Energy Consumption (AEc) (kWh/year) Storage Volume (l) Coldest Storage Temperature (°C) Defrosting Type The energy consumption is based on standard test results for 24 hours.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.