HCG450 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
002 LINGUE 28-09-2005 19:29 Pagina 22 General warnings GB IE Dear Customer, Thank you for choosing our product. This appliance is easy to use; read this handbook carefully before installing and using it, however. You will find the correct indications for the best installation, use and maintenance of the product. • Very important: keep this instruction booklet with the appliance in case you pass it on to someone else.
002 LINGUE 28-09-2005 19:29 Pagina 23 General warnings GB IE • If a gas appliance is used for a long time it may require extra ventilation (opening a window or increase of the forced exhaust). • Be careful not to place saucepans with unstable or deformed bottoms on the burner to avoid accidents by overturning or spilling over of liquid. • If a burner is turned off accidentally turn off the control knob and try to light it again after waiting at least a minute.
002 LINGUE 28-09-2005 19:29 Pagina 24 Instructions for use GB IE Description of the main parts of the appliance 1 2 3 4 6 5 1 = grid 2 = cover 3 = spreader 4 = ON spark plug 5 = safety valve (for models equipped with a safety valve) 6 = knob for burner ignition and adjustment 22
002 LINGUE 28-09-2005 19:29 Pagina 25 Instructions for use GB IE The hob control area houses the devices and knobs for operation of the gas burners. Operation of gas burners In order to ignite a burner, it is necessary to depress the knob while rotating it anticlockwise, till the index is aligned with the position corresponding to the maximum gas delivery (i.e. the large flame symbol).
002 LINGUE 28-09-2005 19:29 Pagina 26 Instructions for use GB IE Advice on the use of gas burners For lower gas consumption and a better yield, use saucepans with diameter suitable for the burners, avoiding the flame coming up round the side of the saucepan (see the Container Table). Use only flat-bottomed pans. As soon as a liquid starts to boil, turn the flame down to a level sufficient to maintain boiling.
002 LINGUE 28-09-2005 19:29 Pagina 28 Instructions for use GB IE Maintenance and cleaning Do not use jet of steam for cleaning. Before any operation disconnect the appliance electrically. Wash the enamelled parts with lukewarm water and detergent. Do not use abrasive products. Wash the burner spreader frequently with boiling water and detergent being sure to remove any deposits which could block the flame outlet. Rinse the stainless steel parts well with water and dry them with a soft cloth.
002 LINGUE 28-09-2005 19:29 Pagina 29 Instructions for installation GB IE Below we give the instructions for qualified installers so that the installation, setting and maintenance operations are performed correctly and according to the regulations in force. Positioning This appliance isn’t connected to any scavenging devices of combustion products. The appliance can only be installed and operate in permanently ventilated rooms according to the local regulations in force.
002 LINGUE 28-09-2005 19:29 Pagina 30 Instructions for installation GB IE To perform these operations the qualified installer will follow the indications given in the "Adaptation to the various types of gas" section. For safety operation make sure that the supply pressure respects the values given in the "Table of burner and injector characteristics”. If the appliance is supplied with liquid cylinder gas, make sure that the cylinder pressure regulator conforms to the local regulations in force.
002 LINGUE 28-09-2005 19:29 Pagina 31 Instructions for installation GB IE ELECTRICAL CONNECTION The appliances are provided with a three-pole feeding cable and work with alternate current and single-phase voltage indicated on the “rating plate of the product “report at the end of the instruction manual and on the product. The grounding conductor of the cable is marked with the colours yellow/green.
002 LINGUE 28-09-2005 19:29 Pagina 32 Instructions for installation GB IE Adaptation to different types of gas To adapt the appliance to a gas different from that for which it was set up (see label on both the packaging and the bottom of the appliance) proceed as follows: • remove the grids • remove the covers and the spreaders • with a 7 mm socket spanner unscrew and remove the injectors.
002 LINGUE 28-09-2005 19:29 Pagina 33 Instructions for installation GB IE Setting the minima The flame on the small output is regulated in the factory. When the injectors have been replaced or there are special mains pressure conditions, it may be necessary to regulate the minimum again.
002 LINGUE 28-09-2005 19:29 Pagina 34 Instructions for installation GB IE Burner and nozzle characteristic table CAT.
002 LINGUE 28-09-2005 19:29 Pagina 35 Instructions for installation GB IE Instructions for building in the units The appliance is of class 3. It can be installed with just one side part (to right or left of the hob) higher than the cooking hob and placed at a minimum distance as shown in figure. It can be built into all units whose walls withstand a temperature 65°C higher than room temperature (UNI EN 30-1-1 e/o CEI EN 60335-2-6). Avoid installing the appliance near inflammable materials (e.g.
002 LINGUE 28-09-2005 19:29 Pagina 36 Instructions for installation GB IE • Position the special sealed gasket (provided) on the edge of the hob making sure that the ends meet without one lying on top of the other. • Put the hob in the unit opening making sure that it is centred. • Fasten the hob to the unit with the fastening brackets. The traction of the screws will be enough to cut the sealing gasket so that the excess can easily be removed.
