SA116 Single Oven Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Important • Read the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly. • Remove spills as soon as they occur. • Always use oven gloves when removing shelves and trays from the ovens. • Do not allow children near the oven when in use. • Do not allow fat or oils to build up on the oven shelves, grill pan or oven base. • Do not place any cooking utensils or plates directly on the oven base.
First use of the oven First use • Before using the oven for the first time we recommend that you clean the oven with soapy water, rinse carefully and then heat on each of the below programmes at maximum temperature for the specified time. A slightly unpleasant smell may be produced, caused by grease remaining on the oven elements from the production process. 60 minutes conventional oven. 15 minutes grill.
Oven controls & use Cooking function knob To set the function, turn the cooking function knob clockwise to the required function. Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time. These are explained below: Conventional Oven This function uses the top and bottom heating elements with a temperature between 50OC and Max. Natural convection creates a perfect cooking zone in the centre of the oven.
Changing the Oven Lamp Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. Changing the bulb (fig. 1) IT • Unscrew the protective cover. o • Unscrew and replace the bulb with the new one suitable for high temperatures (300 C) having the following specifications: 230-240V 50Hz, 15W, E14.
Cleaning and Maintenance Removing the Oven Door The oven doors can easily be removed as follows: • Open the door fully. • Open the lever on the left and right hinges (as show in figure 2). • Gently close the door until left and right hinge levers are hooked to the door. • Lift the door by removing the hinge hooks from their location in the direction indicated. • Rest the door on a soft surface. • To replace the door, repeat the above steps in reverse order. fig.
Cleaning and Maintenance Removing the Oven Door Inner Glass To remove the inner pane of the top oven door on both sides 1. Remove the oven door as shown below. 2. Release the two upper blocks by pressing down as shown in fig. 3. 3. Slide the door glass out in the direction shown in fig. 3.1. 4. Clean the glass with an appropriate cleaner, dry thoroughly and place on a soft surface. 5. Now you can also clean the inside of the outer glass. To replace the inner glass 1.
Installation Important If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not installed as it could restrict ventilation. Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit.
Electricity supply to your oven Warning! this appliance must be earthed. This appliance must be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E and local regulations. The wires in the mains lead are coloured in accordance with the following code: GREEN AND YELLOW = EARTH BLUE = NEUTRAL BROWN = LIVE.
Notes :
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
