WF140 Freestanding Dishwasher Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Recomendations • To reduce energy and water consumption, remove all dirt residues from the dishes prior to loading the dishw• • Only run the dishwasher only when fully loaded. • Place hollow items (bowls, glasses and pans) face down in the basket. Before first use • Set the water softener level as required by the water hardness in the area. • Add 2kg of salt into the salt compartment and then fill with water to the top of the salt compartment.
Control Panel Starting a programme • Press the Power button (1) to switch the dishwasher on. • Turn the Programme Selection Dial (2) until the required programme is indicated. • If required, press the Delay Timer button (3) repeatedly to set the programme. • If required, press the Prewash button (4). • Ensure the dishwasher door is closed. • Press the Start/Pause button (5) to begin the programme. If possible, do not open the dishwasher door once the programme has started.
1. Push the latch as shown in figure 1. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks.
The efficiency of your dishwasher depends of theittap water. To ensure best efficiency, thethe dishwasher obtained through testing strip. after taking strip in on the softness strip. Testing stripthrough is equipped with a system thefor hardness in the mains water supply. The efficiency will increase when the of water. water 1 out your that tap reduces system is correctly set. To the water hardness level of your water supply you can use the test strip supplied or 1 find out sec.
nse Aid RinseRinse Aid Aid fill the rinse aid compartment Rinse Aid To fill theTorinse aidrinse compartment fill the aidcompartment compartment To fill the rinse aid Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning and removing the cap 1. Open the rinse aid compartment by turning and removing the as cap as shown in figure 4. 1. Open the rinse aid compartment by turning and removing the cap as shown inshown figurein4.figure 4. in figure 4.
Dishwasher Baskets Alternative basket loads Lower Basket To adjust the height of the upper basket: 1. Open the basket retaining clips, as shown in figure 7, but turning them to the side. 2. Remove the upper basket, and relocate the alternate set of wheels on the runner, as shown in figure 8, pushing the basket back into place. 3. Close the basket retaining clips. fig 7 The images below are designed as guidance as to best practice for loading the dishwasher.
Standard loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid • 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Economic 50°C, in accordance with EN 50242 (international norms.).
Programme Listing Programme names and temperatures Prewash No heat Quick 40O wash Economic 50O wash Normal 55O wash Intensive 65O wash Extra intensive (Prewash and intensive Type of food waste Pre-wash to rinse and loosen residue-awaiting full load-then select a programme Coffee, milk, tea, cold meats, vegatables, not kept for long Coffee, milk, tea, cold meats, vegatables, not kept for long Soups, sauses, pasta, eggs, pilaf, potatoe and oven dishes, fried foods Soups, sauses, pasta, eggs, pilaf
Unplug your machine ime maythat accumulate intemperature, the machine's section.InIncase case such gramme runs at high andwashing start the machine. ofof insufficiency, useand turn off its ta Do not use hard materials when cleani ation; ecial cleansing material available in the market. (Cleansing material produced special to and a dampened cloth. chines bycompartment detergent producers.) etergent without loading any dishes into the machine, select a me that runs at high temperature, and start the machine.
Failure Codes and Troubleshooting Your dishwasher control panel is equipped with a diagnostic display to help in the event of a pr Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance.
Failure Code and Troubleshooting Problem The programme will not start Water remains inside the dishwasher at the end of the programme Possible cause Check the plug, fuse and circuit breakers of the mains supply The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked The water drain hose is blocked or kinked.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
Installation • Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation. • Ensure the appliance is level by adjusting the feet as necessary. • Only use the water inlet supplied with the appliance. • If the water pressure is above 10 bar, a pressure relief valve should be used.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.