Instructions / Assembly
ETL LISTED
CONFORMS TO
UL STD 1863
ANSI/UL STD 60950-1
CERTIFIED TO
CAN/CSA STD C22.2 NO 60950-1
Installation Instructions:
Location Selection
Find a central location for the panel so as to allow equal lengths of wire to be run to locations throughout the home. The l ocation of the panel should be so that the surrounding temperatures do not exceed
122º F (50º C) or go below 32º F (0º C). Exposure to high humidity levels should be avoided so as to prevent condensation in the panel.
Caution: Consult local building and electrical codes before installing any equipment.
Step 1:
Installation of Back Panel
Place plate with telephone 110 IDC on wall location and trace openings for cutouts on wall (see Figure 1). Now trace openings for four (4) installation holes. Remove plate and make cutouts for
cables.
Insert drywall anchors. Now pull both telephone and coax cables through the opening in the wall and the plate (see Figure 2). Using the supplied screws, attach the plate to the wall.
Step 2: Installation of Telephone Wires
Install the wire from the telephone demarcation point to the 110 IDC marked from Telco (see Figure 3).
Install the twisted pair cables from each location in the house to the remaining 110 IDC connectors. Match the color-coding of the wires to the colors on the 110 IDC connectors. Incoming
phone service can be tested using the test port.
All cables should be punched down, using an industry standard punch-down tool, to the 110 IDC connectors following the T568A wiring configuration as shown below.
Line 1 is Blue, Line 2 is Orange, Line 3 is Green and Line 4 is Brown.
Step 3: Installation of Coax Cables
Attach an F-connector onto the cable TV service or satellite service incoming cable. Screw the incoming cable with F-connector to the splitter connector marked input (see Figure 4).
Connect F-connectors to all coaxial cables that have been pulled through the opening in the wall plate. Connect these remaining cables to the splitter.
Secure the cover of the 5050 module to the back panel and tighten screws located at the top and bottom of the back plate of the module (see Figure 5).
WARNING
CE Tech’s products shall be installed and used only as indicated in CE Tech’s instruction sheets.
CAUTION
Never install telephone wiring during lighting storms.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Never touch un-insulated wires or terminals unless the telephone line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
SAVE THESE INSTRUCTIONS.
This Product Should be Installed By an Electrician, Low Voltage Installer or Qualified Person in Accordance with Electrical and Low Voltage Codes
Instruction / Installation Sheet
Home Command Center II 5050
U.S. Patent 6768055
RoHS Compliant
Parts Included:
1. Home Command Center II
2. Four (4) Screws
3. Four (4) Drywall Anchors
Tools Needed:
1. Drywall Saw
2. Screwdriver
3. 110 Punchdown Tool
4. Pencil
Fig. 3
Fig. 1
Fig. 4
Fig. 5
5050 Rev 2
Page 1 of 1
Fig. 2
T568A Wiring Configuration
MADE IN CHINA
HECHO EN CHINA
DISTRIBUTED BY
DISTRIBUIDO POR
HOME DEPOT U.S.A., INC.
2455 PACES FERRY RD., N.W.
ATLANTA, GA 30339
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM