Item #524-226 Model #60424N USE AND CARE GUIDE FULL MOTION FLAT PANEL TV WALL MOUNT (FITS VESA 100/200/300/400) Questions, problems, missing parts? Before returning to the store, call CE Tech Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 1-877-527-0313 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in CE Tech through the purchase of this wall mounting system. We strive to continually create quality products designed to enhance your home.
Table of Contents Table of Contents ..................................2 Safety Information .................................2 Warranty .................................................3 Pre-Installation ......................................4 Installation .............................................7 Safety Information Before you begin, carefully read and understand the instructions in this manual. Please follow the instructions in the order presented in this manual and observe all warnings and cautions.
Warranty The manufacturer warrants that it will replace or repair this item, free of charge, at the manufacturer’s sole discretion, should it prove defective in materials or workmanship.
Pre-Installation PLANNING INSTALLATION Compare all parts in the package with the Hardware Included and Package Contents lists in this manual. If any part is missing or damaged, do not install this wall mount system and call customer service at 1-877-527-0313 or visit www.HomeDepot.com. This wall mount bracket is compatible with VESA 100/200/300/400 mm mounting holes: 19.5" (496.5 mm) 2.
Pre-Installation (continued) TOOLS REQUIRED (NOT INCLUDED IN THE PACKAGING) 5/32 in. (4 mm) wood drill bit or ¼ in. (6 mm) + 3/8 in. (10 mm) masonry drill bits Power drill Stud finder Level Measuring tape Phillips screwdriver Pencil Hammer HARDWARE INCLUDED NOTE: Hardware not shown to actual size. NOTE: The hardware included is suitable for mounting to walls made of brick, solid concrete, or wood studs covered with drywall.
Pre-Installation (continued) PACKAGE CONTENTS A C D B2 B1 Part A B1/B2 Description Quantity Mounting arm 1 Left and right wall covers 2 C Mounting plate D Extension rod (left and right) 1 6 2 each
Installation 1 Identifying the screw diameter to use 2 Identifying the screw length to use □ Insert a straw or toothpick into one of the mounting holes on the back of your TV. If your TV is curved or recessed, place the proper sized spacer (II) on top of one of the mounting holes first. □ Use a pencil to mark the depth of the mounting hole. □ Determine the proper screw length to use by comparing the mark with the various screws provided.
Installation (continued) 4 Drilling mounting holes in concrete/brick wall 5 If you are installing the mounting system into wood studs, proceed to step 5. Drilling mounting holes in wood studs CAUTION: Avoid drilling near electrical wiring and water pipes. The mounting system must be attached to a weight bearing wall and must be installed directly onto the center of the wood studs. Failure to observe all safety precautions can result in serious physical injury and/or property damage.
Installation (continued) 7 □ Attaching the mounting brackets to the arm 8 This procedure describes how to attach the mounting plate to VESA 100 and 200 TVs. For VESA 300 and 400, proceed to step 9. □ Align spacers (II) over the mounting holes on the back of your TV. □ Position the mounting plate (C) over the spacers (II) and attach the plate to the TV using the appropriately sized screws (HH) and washers (GG).
Installation (continued) the TV to the 10 Attaching mounting arm 11 Adjusting the angle of the TV □ Adjust the angle of the TV to a maximum of 10° by loosening the side nuts (1) on the mounting arm (A) and moving the TV to the desired angle. Re-tighten the nuts (1) after you reach the desired angle. CAUTION: Use two or more people to complete this step.
Questions, problems, missing parts? Before returning to the store, call CE Tech Customer Service 8 a.m.- 6 p.m., EST, Monday-Friday 1-877-527-0313 HOMEDEPOT.COM Retain this manual for future use.
