GB5MV-10-LD GB6MP-10-LD-U GB8MP-10-LD-U Operation Manual NL48P July 2005
CONTENTS Important Owner Information_____________________________________1 Introduction____________________________________________________1 Important Safety Instructions___________________________________2 Model Description_______________________________________________3 Specifications__________________________________________________3 Plug Configurations_____________________________________________3 Installation____________________________________________________4 Start-up Procedure_______________________
IMPORTANT OWNER INFORMATION Record the model number, serial number (identification plate is located behind front door), voltage and purchase date of your Cecilware Cappuccino Dispenser in the spaces below. Please have the information available when calling Cecilware for assistance. Model #: Serial #: Voltage: Date of Purchase: Business Hours: 8:30 a.m. to 5:00 p.m.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS The GB8MP-10-LD-U (only) is equipped with two (2) power switches and two (2) 120 volt grounded power cords. To avoid any injury, turn both power switches OFF. Or, unplug both power cords and allow unit to cool completely before performing any maintenance or cleaning.
MODEL DESCRIPTION GB8MP-10-LD-U (shown) GB5-LD-U & GB6MP-10-LD-U (typical) These High Volume Cappuccino Dispensers will hold double the amount of your most popular flavor along with up to seven other flavors as well. With these Dispensers you will not waste valuable time refilling product Hoppers or lose profits during peak sales periods. With the hot water dispense button, you can increase sales by offering the ability to add packet items to your menu as well.
UNPACKING INSTRUCTIONS Carefully unpack the Cappuccino Dispenser Unit and inspect immediately for shipping damage. Your Cappuccino Dispenser Unit was shipped in a carton designed to give it maximum protection in normal handling. It was thoroughly inspected before leaving the factory. In case of damage, contact the shipper. DESCRIPTION AND LOCATION OF COMPONENTS Note: Refer to Illustrations for description and location of COMPONENTS and CONTROLS. 1. HOPPERS.
START-UP PROCEDURE Caution: Make sure that the Heater Switches, are in the OFF position. 1. Connect the ¼ inch copper waterlines to the ¼ inch flare water inlet fittings of the valves. 2. Plug the power cords into dedicated receptacles. 3. Activate the Power Switch (Toggle Up). The door display panel, the red power indicator lights and the green dispense buttons will light up and the tanks will start filling. Allow approximately 4-5 minutes for the tanks to fill. 4. Activate the Heater Switch.
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock, DISCONNECT POWER CORDS before repairing or replacing any internal components of the unit. Before any attempt to replace a component be sure to check all electrical connections for proper connection. PROBLEM 1 Light display not lit. PROBABLE CAUSE A Dispensing unit unplugged. REMEDY Reconnect dispensing unit. B No power from Terminal Block. Check the Terminal Block for loose wire. C Defective Bulb. D Defective Ballast. Replace Bulb.
Model L690A (Rev. B) Dual Probe Liquid Level Controller Overview - The L690A is a Dual Probe Liquid Level Controller designed to maintain a specific level of water in the tank. This device utilizes two level probes for increased reliability. Independent maximum fill timers are incorporated in the controller for overflow protection. Operation - When a fill problem occurs, the Dual Probe Liquid Level Controller turns OFF power to the fill valves and remains OFF until the power input is reset (i.e.
1. ROTATE PRODUCT GUIDES UP, REMOVE HOPPERS AND REFILL WITH PRODUCT. 2. REPLACE HOPPERS, ROTATE PRODUCT GUIDES DOWN. 3. EMPTY DRIP TRAY. 4. SANITIZE* ALL EXTERIOR SURFACES. 1. RINSE WHIPPER CHAMBERS - POSITION PAN UNDER DISPENSE TUBES. - MOVE RINSE SWITCH TO "RINSE". - PUSH AND HOLD EACH DISPENSE BUTTON 3 TO 5 SEC. - MOVE RINSE SWITCH TO "SERVE". 2. EMPTY DRIP TRAY WASH, RINSE, AND SANITIZE* 1. PRODUCT HOPPER CLEANING - ROTATE PRODUCT GUIDES UP, REMOVE HOPPERS FROM MACHINE. - EMPTY POWDER INTO PANS.
GB5MV-10-LD (VISTA) 5 Flavor Cappuccino Dispenser Door not shown HOPPER (4) (CD185) PRODUCT GUIDE POWER SWITCH RINSE SWITCH GRILL DRIP TRAY PAN 5 Lbs 5 Lbs 5 Lbs 5 Lbs 10 Lbs HOPPER (1) (CD179) HEATER LIGHT HEATER SWITCH WHIPPER CHAMBER
DRIP TRAY PAN GRILL SLANTED WHIPPER CHAMBER PRODUCT GUIDE HOPPER (CD185) 5 Lbs 5 Lbs 5 Lbs 21.5" 5 Lbs 5 Lbs 10 Lbs RINSE SWITCH HEATER LIGHT POWER SWITCH DRIP TRAY PAN (2) GRILL WHIPPER CHAMBER PRODUCT GUIDE HOPPER (CD185) 5 Lbs 5 Lbs 5 Lbs 5 Lbs 5 Lbs 5 Lbs HOT WATER (OPTIONAL) 27.
WHIPPER CHAMBER IMPORTANT: SLANTED WHIPPER CHAMBERS (SEE BELOW) ARE NOT INTERCHANGEABLE WITH STANDARD STRAIGHT WHIPPER CHAMBERS. BE SURE TO ORDER USING THE CORRECT PART NUMBERS.
HOPPER COVER AGITATOR WHEEL W/SPRINGS AUGER MOTOR #CD175 (90 RPM) AUGER BUSHING FRONT CD306 NUT CD278 [2] BEVELLED SOCKET CD271 PRODUCT GUIDE, SHORT CD70A AUGER BUSHING-BACK CD279 HOPPER BASE CD140
HOPPER COVER AGITATOR WHEEL W/SPRINGS AUGER MOTOR #CD175 (90 RPM) AUGER BUSHING FRONT CD306 NUT CD278 [2] BEVELLED SOCKET CD271 PRODUCT GUIDE, SHORT CD70A AUGER BUSHING-BACK CD279 HOPPER BASE CD140
BODY ASS'Y GB5MV-10-LD (Vista) ITEM DESCRIPTION P/N QTY
DOOR ASS'Y GB5MV-10-LD (Vista) ITEM DESCRIPTION P/N QTY
2 1 3 4 DOOR ASS'Y GB6MP-10-LD-U (Panorama) GB8MP-10-LD-U (Panorama) 5 6 11 10 9 8 7 8 9 10 11 ITEM NO.
ITEM DESCRIPTION P/N QTY
TANK DIMENSIONS: 12" WIDE, 4.8" DEEP, 16.5" HIGH. APPROX. 3.7 GAL.
TANK DIMENSIONS: 15" WIDE, 6" DEEP, 18" HIGH. APPROX. 6 GAL.
BLK BREW SWITCH BREW SWITCH YEL WHT BREW SWITCH BRN WHT BREW SWITCH VIO WHT BREW SWITCH RED DISPLAY LIGHT ORG WHT WHT BLK DOOR UNIT GND MAIN UNIT DISPENSE VALVE DISPENSE VALVE DISPENSE VALVE RINSE SWITCH A1 A2 43 NO 44NO 31 NC 32NC 21NC 22 NC 13 NO 14NO BLK DISPENSE VALVE GND DISPENSE VALVE AUGER AUGER AUGER AUGER CONTACTOR AUGER WHIPPER WHIPPER BLK BLK RELAY RELAY WHIPPER BLK WHIPPER BLK RELAY WHIPPER BLK RELAY RELAY BLU L1 WATER INLET VALVE LIQUID LEVEL
GB6M-10-LD-U
DISPLAY LIGHTS LIQUID LEVEL CONTROL WATER LEVEL PROBES WATER GB8M-10-LD-U & GB8M10WLD ELECTRICAL DIAGRAM - LEFT SIDE - 120V REV A NE195 SHEET 1 OF 2
DISPLAY LIGHT LIQUID LEVEL CONTROL WATER LEVEL PROBES WATER GB8M-10-LD-U & GB8M10WLD ELECTRICAL DIAGRAM - RIGHT SIDE - 120V REV A NE195 SHEET 2 OF 2
