MT-2UL-BL,MT-3UL-BL OPERATOR’S MANUAL NS10A
MT UL BL TABLE OF CONTENTS 1 TECHNICAL CHARACTERISTICS ................................................................................. 5 2 INTRODUCTION ............................................................................................................. 5 3 INSTALLATION ............................................................................................................... 5 4 TO OPERATE SAFELY .........................................................................................
MT UL BL MT 2 UL BL MT 3 UL BL 1 TECHNICAL CHARACTERISTICS n 2 3 Gal 2.5 2.5 5- width Inches 14.25 21 6- depth Inches 18.5 18.5 height Inches Transparent removable bowls Capacity of each bowl, approx. 3- 4- Dimensions: 27.75 27.75 Net weight, approx. kg 81.5 108 Gross weight, approx. kg 95 125 Adjustable thermostats n 2 3 Hermetic compressor Air-cooled condenser Safety pressure switch damage is found, call the delivering carrier immediately to file a claim.
MT UL BL gallons) is shown by marks on the bowl. 3 - In case of products to be diluted with water, pour water into bowl first, then add correct quantity of product. In case of natural squashes, it is advisable to strain them, in order to prevent pulps from obstructing the faucet outlet. 4 - To obtain the best performance and result, use bases designed to be run in Granita freezers. Such bases have a sugar content of 34 degrees Baumé corresponding to 64 degrees Brix.
MT UL BL 11 -Restrictor cap: when the unit is used in Soft Drink mode it is advisable to install the restrictor cap on the faucet outlet in order to reduce the drink outflow (see figure 4). figure 3 2 - Beverage temperature adjustment: proper beverage temperature is factory preset. To reset, turn the knob located in each switch box as follows: - towards right (clockwise) to decrease temperature. - towards left (counterclockwise) to increase temperature.
MT UL BL 4 - Remove the bowl gasket from its seat (see figure 9). figure 6 3 - Slide the outer spiral out (see figure 7) and then the inside auger (see figure 8). figure 9 5 - Dismantle the faucet assembly (see figure 10). figure 7 figure 10 6 - Slide the drip tray out and empty it. 5. 3. 2 CLEANING ATTENTION Before any disassembly and/or cleaning procedure make sure that the dispenser is disconnected from its power source.
MT UL BL solution will not provide adequate cleaning. wall (see figure 12). IMPORTANT In order to prevent any damages to the dispenser use only a detergent suitable with plastic parts. 2 - Using a brush, suitable for the purpose, thoroughly clean all disassembled parts in the cleaning solution. ATTENTION When cleaning the machine, do not allow excessive amounts of water around the electrically operated components of the unit. Electrical shock or damage to the machine may result.
MT UL BL properly engaged (see figure 15). the two plastic coated screws (see figure 16). figure 16 figure 15 3 - Replacement of lighted top cover bulb: remove the fixing screw placed in the upper part of the top cover, remove the lower part and replace the bulb (using a 24-28V 21W max bulb). Reassemble the top cover and replace the fixing screw.(see figure 17) 8 - Use fresh product to chase any remaining sanitizer from the bottom of the bowl(s). Drain this solution. Do not rinse out the machine. 5.
MT UL BL automatically switches the dispenser from Granita mode to Soft Drink mode and the opposite. This means that during defrost periods frozen Granita will melt to thermostat setting temperature and once defrost period has expired, the product automatically freezes down again to Granita setting viscosity. figure 18 To operate the defrost timer proceed as follows (see figure 18). 1 - Set the time of the day by rotating the dial clockwise (arrow A).
SPARE PARTS LIST 2422_49 V 1.
1 00263 Transparent cover 29 >>> Starting-run capacitor 55 00177 Fixing ring 2 00638 Bowl 30 00158 Rubber leg 56 00132 Thermostat 3 00420 Faucet piston 30 00092 4” leg 57 00182 Thermostat knob 4 00101 Faucet piston OR 31 >>> Solenoid valve coil 58 PPP Transformer 5 00640 Black faucet handle 33 00087 Density adjustment screw 59 00231 Insulation foam 6 00447 Faucet handle spring 34 00720 Shaped nut 60 00449 PWB housing 7 00498 Black faucet handle pin 35
GEAR MOTOR SPARE PARTS LIST 1 00097 Bracket with bush 10 00247 Ball bearing ý 28 mm 20 00721 Gear box cover 2 00156 Stator 11 00257 1.5 mm spacer 22 00180 Rotor 3 00296 Stator protection gasket 12 00184 Third gear 23 00187 Pinion 4 00168 Washer 13 00165 Fourth gear 24 00169 Bushing 5 00253 Rotor spacer 14 00258 3.
MT UL BL NOTES: 15
CECILWARE CORPORATION 43-05 20th Avenue Long Island City, N.Y. 11105 Tel. (800) 935 2211 Fax (718) 932 7860 customer.service@cecilware.com www.cecilware.com 2422_49 R1.