WPP(HOB)-531-D2 OR SSP-511-D2-SPK1.07UNVL-ADA-ISSUE4.0 SERVICE MANUAL FOR MODEL WPP-531-D2 WEATHERPROOF TELEPHONE OR MODEL HOB-531-D2 WEATHER RESISTANT TELEPHONE OR MODEL SSP-511-D2 STAINLESS STEEL PANEL TELEPHONE WITH OPTIONAL SECOND-NUMBER AUTO DIAL FEATURE AND OPTIONAL ADA FEATURE EQUIPPED WITH SPK1.
Issue 4.0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL NUMBER MODEL WPP-531-D2, HOB-531-D2, OR SSP-511-D2 WITH SPK1.07UNVL FIRMWARE SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support.
Issue 4.0 TABLE OF CONTENTS SECTION PAGE 1.0 INTRODUCTION..................................................................................................... 4 2.0 GENERAL ................................................................................................................. 4 3.0 PROGRAMMING .................................................................................................... 5 PROGRAMMING CONTINUED… .......................................................................
Issue 4.0 1.0 INTRODUCTION The practices in this manual provide installation and maintenance information for Model WPP-531-D2 or Model SSP-511-D2 Telephone, with optional secondnumber auto-dial feature and optional ADA feature, equipped with SPK1.07UNVL firmware. The information in this manual is subject to change without notification.
Issue 4.0 3.0 PROGRAMMING NOTE: It is recommended that you ground yourself to prevent ESD damage to the PCB(s). 3.1 Connect the telephone to a working telephone line or a DTMF test set. 3.2 Locate the pair of plastic mini-jumpers along the edge of the PC board. Move them to the “ON” or inner most position as depicted in the diagram, on the last page of this manual. 3.
Issue 4.0 PROGRAMMING CONTINUED… 3.8 If a second auto-dial number is desired, enter # 0 1 followed by the desired second auto-dial number. This number will automatically dial out after the selected number of unanswered rings from the first auto-dial number. The number of rings is selected under Digit 6 in programming section 3.9. The second auto-dial number may be up to eleven (11) digits in length. If this is not a desired feature, proceed to section 3.9. Example: Enter # 0 1 7 7 7 1 3 1 3.
Issue 4.0 PROGRAMMING CONTINUED… After entering # 0 0, enter a series of ten Digits as selected below: Digit 1 0 Always 0 for this model. Digit 2 0 No incoming calls allowed. 1 Incoming calls allowed. Digit 3-(Automatic call disconnect: 1 thru 9 min. available) 0 No automatic call disconnect. 1-9 Minute(s) conversation automatic call disconnect. Digit 4 0 Always 0 for this model. Digit 5 0 Always 0 for this model. Digit 6-(2nd Number Auto-Dial Setting) 0 Deactivate ADA feature. 1-9 Activate ADA feature.
Issue 4.0 4.0 TESTING/OPERATION 4.1 With the phone connected to a working telephone line, press the “CALL” button located on the front of the telephone. The LED will illuminate red at this time. 4.2 If any PBX access code or number was programmed (section 3.6), it will automatically dial out, before the programmed auto-dial number. There will be an approximate one (1) second pause between the two numbers. 4.
Issue 4.0 5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT DTMF Test Set Volt/Ohm Meter 3/8” Nut Driver 6.0 5/16” Nut Driver Flat Blade Screw Driver Security Tool-CEECO P/N 301-064 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6.1 Using a 301-064 security tool (sold separately) remove the four security screws. 6.2 The security tool is for a standard 5/32” button screw generally used on the framework of the phone booths. 6.3 Separate the cover assembly from the Weatherproof housing or enclosure. 6.
Issue 4.0 7.0 SPECIFICATIONS INPUT POWER: C.O. Line Powered (48-52 Volt Loop) LOOP CURRENT: 30 mA min. 80 mA max. IMPEDANCE: 600 Ohms. SIGNALING: DTMF, 70 ms tone, 50 ms spacing. RINGER EQUIVALENCE: 0.4a TYPE JACK: RJ11C OUTPUT: -4.0 to –6.0 dbm. ENVIRONMENTAL: Temperature 0C to 50. Humidity 20% to 90%. PROGRAMMING: Via DTMF keypad.
Issue 4.0 8.0 PARTS LIST QUANTITY PART NUMBER DESCRIPTION 4 331-006 Outer cover security screw. 1 301-018 Modular line cord. 1 301-054-UL Modular Connector (RJ11C). 1 700-008 Keypad Cable. 1 660-000 CEECO SPK PC board. 1 705-110 Connectorized Keypad. 1 6020 Momentary Panel Switch. 1 14024 Speaker. 1 14067 Microphone. 1 331-005 Weatherproof housing (WPP) 1 331-010 Stainless Steel Panel. 1 12017 Ringer 301-064 Security Tool.
Issue 4.0 9.0 FCC NOTICE 9.1 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that you be advised of certain requirements involving the use of this telephone. 9.2 CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK The FCC requires that you connect this telephone to the Nationwide Telephone Network through a registered jack provided by the Telephone Company in your area.
Issue 4.0 10.0 REPAIR AND RETURN INFORMATION 10.1 WARRANTY REPAIR Any device returned requiring warranty service, repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include return shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container. 10.
Issue 4.0 11.0 WARRANTY POLICY 11.1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 12 months from the date of original shipment, if properly installed and maintained. This warranty is limited to the value of material only. CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse and improper use or improper installation.
Issue 4.0 12.0 DIAGRAM Locate the mini jumpers on the corner of the PCB. O N O MOVE THE MINI JUMPERS TO THE ON POSITION BEFORE GOING OFFHOOK. When programming is completed, move the mini- jumpers to the OFF position. O FF N O O FF N O FF NOTE: Do not leave the mini jumpers in the ON position; this will decrease battery life.