WPP-531-DD OR SSP-511-DD-SPK-DD-ADA-R1(1999)-BlackButtons-ISSUE4.
ISSUE 4.0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL NUMBER MODEL WPP(HOB)-531-DD-ADA OR SSP-531-DD-ADA EQUIPPED WITH SPKDD-ADA-R1 FIRMWARE SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support.
ISSUE 4.0 TABLE OF CONTENTS SECTION PAGE 1.0 INTRODUCTION................................................................................................... 4 2.0 GENERAL ............................................................................................................... 4 3.0 PROGRAMMING .................................................................................................. 5 PROGRAMMING CONTINUED… ..................................................................... 6 3.
ISSUE 4.0 1.0 INTRODUCTION The practices in this manual provide installation and maintenance information for the CEECO Model WPP 531-DD-ADA Handsfree Weatherproof Telephone or Model SSP-511-DD-ADA Handsfree Stainless Steel Panel Telephone. The information in this manual is subject to change without notification. For information not included in this manual, please call or write: CEECO Customer Service 519 West South Park Street Okeechobee, FL 34972 (863) 357-0798 FAX (863) 357-0006 2.0 GENERAL 2.
ISSUE 4.0 3.0 PROGRAMMING 3.1 Separate the telephone assembly from its mounting or housing by loosening the four security screws on the stainless steel panel with a security tool (sold separately) and remove them. 3.2 Connect the telephone to a working telephone line or DTMF test set. 3.3 Locate the two plastic mini-jumpers on the edge of the PC board and place them in the "ON" position, as depicted on the last page of this manual. 3.
ISSUE 4.0 PROGRAMMING CONTINUED… LOCATION #00 Digit 1: Always 0. Not used in this model. Digit 2: 0 No incoming calls allowed. 1 Incoming calls allowed. Digit 3: 0 Use narrow dial tone detect window. 1 Use wide dial tone detect window. Digit 4: 0 Time-out disconnect enabled. 1 Time-out disconnect disabled. Digit 5: 0 Time-out of 1.5 minutes. 1 Time-out of 3.0 minutes. *Do not stop your programming sequence yet, however. You must now enter the numbers to be auto-dialed. 3.
ISSUE 4.0 PROGRAMMING CONTINUED… NOTE: A complete programming sequence would appear as follows: #97#0000101#1918005551212#01911. This would set the phone as stated in the examples under sections 3.7, 3.8 and 3.9. Again notice that the programming can be accomplished in one continuous. 3.10 4.0 5.0 When programming is finished, press the LEFT black call button to hang up the phone and return the two plastic mini-jumpers to the "OFF" position, as depicted on the last page of this manual.
ISSUE 4.0 6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6.1 Using a 301-064 security tool (sold separately) loosen and remove the security screws. 6.2 The security tool is for a standard 5/32" button head screw generally used on the framework of the phone booths. 6.3 Separate the faceplate assembly from the weatherproof housing or mounting by pulling the faceplate forward. 6.4 Run the inside station wire into the enclosure and terminate on the RJ1lC terminal block inside. 6.
ISSUE 4.0 7.0 TESTING Action: Connect the phone to the line. Press the LEFT black call button. Reaction: The LED will illuminate red and the preprogrammed number will automatically dial out. The LED will flash red and green during ringing. The LED will turn green when the call is answered (within a maximum of four seconds). A normal speakerphone conversation should take place. Action: When the call is finished, press the left black call button or wait until timeout occurs.
ISSUE 4.0 8.0 SPECIFICATIONS INPUT POWER: C.O. Line powered LOOP CURRENT: 30mA minimum 80 mA maximum IMPEDANCE: 600 ohms SIGNALING: DTMF, 70ms tone, 50 ms spacing OUTPUT: -4.0dbm to -6.0dbm ENVIRONMENTAL: Temperature 0o C to 50o C Humidity 20%-90% PROGRAMMING: Via DTMF keypad. MEMORY RETENTION: Non-volatile storage (does not require power for retention). DIMENSIONS: (SSP) 7 1/6" Wide x 11 1/4" High x 4 1/4" Deep (Handset on hook) MOUNTING: Vertical Surface Mount.
ISSUE 4.0 9.
ISSUE 4.0 10.0 REPAIR AND RETURN INFORMATION 10.1 WARRANTY REPAIR Any device returned requiring warranty service, repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include: return shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container. 10.
ISSUE 4.0 11.0 WARRANTY POLICY 11.1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase. CEECO's obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO. Under no circumstances shall CEECO be liable for loss, damage, cost of repair or consequential damages of any kind which have been caused by neglect, acts of God, abuse or improper operation of equipment.
ISSUE 4.0 12.0 DIAGRAM Locate the mini jumpers on the corner of the PCB. O N O Move the mini jumpers to the ON position BEFORE going offhook. When programming is completed, move the mini jumpers to the OFF position. O FF N O O FF N O FF NOTE: Do not leave the mini jumpers in the ON position; this will decrease battery life.
