WPP(HOB)-531-F OR SSP-511-F-SPKSPD1.00-ISSUE4.0 SERVICE MANUAL FOR MODEL WPP(HOB)-531-F HANDS FREE WEATHERPROOF TELEPHONE AND MODEL SSP-511-F STAINLESS STEEL PANEL TELEPHONE EQUIPPED WITH SPKSPD1.
ISSUE 4.0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL WPP(HOB)-531-F OR SSP-511-F EQUIPPED WITH SPKSPD1.00 FIRMWARE MODEL NUMBER SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support.
ISSUE 4.0 TABLE OF CONTENTS SECTION PAGE 1.0 INTRODUCTION ...............................................................................................................................4 2.0 GENERAL................................................................................................................................................4 3.0 PROGRAMMING .............................................................ERROR! BOOKMARK NOT DEFINED. PROGRAMMING CONTINUED… .....................
ISSUE 4.0 1.0 INTRODUCTION The practices in this manual provide installation and maintenance information for the CEECO Model WPP(HOB)-531-F or Model SSP-531-F Telephone with SPKSPD1.00 firmware. The information in this manual is subject to change without notification. For information not included in this manual, please call or write: CEECO Customer Service 519 West South Park Street Okeechobee, Florida 34972 (863) 357-0798 (863) 357-0006 FAX 2.0 GENERAL 2.
ISSUE 4.0 3.0 PROGRAMMING NOTE: It is recommended that you ground yourself to prevent ESD damage to the PCB(s). 3.1 Connect the telephone to a working telephone line or a DTMF test set. 3.2 Locate the pair of plastic mini-jumpers along the edge of the PC board. Move them to the “on” or inner most position as depicted in the diagram on the last page of this manual. 3.3 Press the “CALL & HANGUP” button and wait for dial tone before entering programming digits. 3.
ISSUE 4.0 PROGRAMMING CONTINUED… Be sure to record your selections below for future reference. #00 0 __ __ __ 0 __ 0 __ 0 __ Digit 1: 0 Always 0 for this model Digit 2: 0 No incoming calls allowed. 1 Incoming calls allowed. Digit 3: 0 Always 0 for this model. Digit 4: 0 No Time Out Feature On Speed Dialing 1 -9 Minutes for Time Out for Speed Dialing Digit 5: 0 Always 0 for this model. Digit 6: 1 Always 1 for this model. Digit 7: 0 Always 0 for this model.
ISSUE 4.0 PROGRAMMING CONTINUED… EXAMPLE: Enter #00 0 _1 _0 _6_ 0 _1 0 _0 0 _5 Phone will be set as follows: DIGIT 1 .. ALWAYS 0 DIGIT 2 .. INCOMING CALLS ALLOWED DIGIT 3 .. ALWAYS 0 DIGIT 4 .. 6 MINUTE TIME OUT FOR SPEED DIALING DIGIT 5 .. ALWAYS 0 DIGIT 6 .. ALWAYS 1 DIGIT 7 .. ALWAYS 1 DIGIT 8 .. DO NOT DIAL PBX NUMBER IN LOCATION #91 DIGIT 9 .. ALWAYS 0 DIGIT 10 .250ms WINK 3.
ISSUE 4.
ISSUE 4.
ISSUE 4.0 SPEED DIAL TABLE CONTINUED… #81 _ - _ _ _ - _ _ _ - _ _ _ _ #86 _ - _ _ _ - _ _ _ - _ _ _ _ #82 _ - _ _ _ - _ _ _ - _ _ _ _ #87 _ - _ _ _ - _ _ _ - _ _ _ _ #83 _ - _ _ _ - _ _ _ - _ _ _ _ #88 _ - _ _ _ - _ _ _ - _ _ _ _ #84 _ - _ _ _ - _ _ _ - _ _ _ _ #89 _ - _ _ _ - _ _ _ - _ _ _ _ #85 _ - _ _ _ - _ _ _ - _ _ _ _ #90 _ - _ _ _ - _ _ _ - _ _ _ _ PROGRAMMING CONTINUED… 3.9 the #00 3.
ISSUE 4.0 4.0 OPERATION 4.1 To make a call, press the black "CALL" button located on the front of the phone. When dial tone is received, the transmitter is muted and the phone waits for numbers to be dialed. 4.2 Press the desired two keys on the keypad to release a pre-programmed speed dial number. The digits should dial out. When answered, a normal speakerphone conversation may take place. 4.2 After the call is complete, press the "CALL" button again to terminate the call.
ISSUE 4.0 6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6.1 Using a 301-064 security tool (sold separately) to remove the four locking screws. 6.2 The security tool is for a standard 5/32" button head screw generally used on the framework of the phone booths. 6.3 Separate the cover assembly from the Housing. 6.4 Run the inside station wire through the Housing and terminate on to the RJ11C modular jack on the housing, as depicted on the following page.
ISSUE 4.0 7.0 OVER-VOLTAGE PROTECTION DIAGRAM 9.0 TESTING Action: Connect the phone to a working phone line. Press the black "CALL" button. Reaction: Dial tone. Action: Press two pre-programmed keys on the key pad. Reaction: The called party answers. A normal speakerphone conversation is allowed. Action: Finish the conversation. Press the "CALL" button, or wait until time-out occurs (if programmed as such). Reaction: The call is terminated.
ISSUE 4.0 10.0 SPECIFICATIONS INPUT POWER: C.O. Line Powered LOOP CURRENT: 30Ma min. 80Ma max.(48 Volt loop) IMPEDANCE: 600 ohms SIGNALING: DTMF, 70ms tone, 50ms spacing LINE OUTPUT -10.0dbm to –12.0dbm ENVIRONMENTAL: Temperature: 0C to 50C Humidity: 20%-90% PROGRAMMING: Via DTMF Keypad TELEPHONE PANEL: Brushed 14 gauge Stainless Steel DIMENSIONS: (SSP) MOUNTING: WEIGHT: 7 1/6" wide x 11 1/4" high x 4 1/4" deep (handset on hook). Vertical surface mount. Approximately 4 lb.
ISSUE 4.0 11.
ISSUE 4.0 12.0 FCC NOTICE 12.1 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that you be advised of certain requirements involving the use of this telephone. 12.
ISSUE 4.0 13.0 REPAIR AND RETURN INFORMATION 13.1 WARRANTY REPAIR Any device returned requiring warranty service; repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include return shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container. 13.
ISSUE 4.0 14.0 WARRANTY POLICY 14.1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase. CEECO's obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO. Under no circumstances shall CEECO be liable for loss, damage, cost of repair or consequential damages of any kind, which have been caused by neglect, abuse, act of God or improper operation of equipment.
ISSUE 4.0 15.0 DIAGRAM Locate the mini jumpers on the corner of the PCB. ON OFF Move the mini jumpers to the ON position BEFORE going off-hook. When programming is completed, move the mini jumpers to the OFF position. ON OFF ON OFF NOTE: Do not leave the mini jumpers in the ON position, this will decrease battery life.