User’s Guide • Copyright: Copyright 2011 All rights reserved by Celluon. All page contents are properties of Celluon. • Celluon, evoMouse®, Magic Cube™ are trademarks or registered trademark of Celluon. All other products are trademarks or registered trademarks of their respective companies. • Please refer to host device instruction manual for Bluetooth pairing information.
Safety Precautions 1. Avoid exposing this product to direct sunlight for extended periods of time, and keep it away from heat sources. 2. There is a risk of malfunction if product is used in places where sudden or extreme temperature changes occur. 3. Applying excessive force or impact to this product may result in product damage, and will void warranty. 4. To ensure safety and prevent damage, use only the dedicated mini-USB to USB cable supplied with this product. 5.
FCC Class B Notice This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Exposure Information The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. possibility of exceeding the FCC radio frequency exposure limit. ❏ Laser Safety IEC 60825 : CLASS I FDA : CLASS II ❏ Caution : Battery may explode if replaced with an incompatible battery. Dispose the used batteries according to the instructions.
❏ Environmentally Friendly Disposal and Recycling This product does not contain any substances known to be hazardous to human health. To protect the environment, dispose of this product separately from household waste once it has reached its end of life, or take it to your nearest Celluon Service Center. 8 About the Built-in Battery Rechargeable Lithium Polymer Battery: Battery Operating Time: Approx. 150 minutes (with continuous use) Capacity: 700mAh (Max)@3.
Contents Cautions 1. For safety reasons, be sure to use only the mini USB to USB cable specified for this product. 2. Make sure to fully charge the battery before using the product for the first time. 3. Battery charging times may vary slightly depending on the ambient temperature. 4. The battery may not be charge to 100 percent of its rated cell capacity even when the battery status LED indicates green light. 5.
1. Product Features 3. How this Product Works •• English QWERTY keyboard layout. •• Compact size for portability – perfect for on-the-go •• Function icons and shortcut keys for ease of operation •• Non-mechanical optical mechanism for superior durability •• Built-in Lithium Polymer rechargeable battery for mobility and convenience •• Compatible with latest devices: Window XP/Vista/7, Windows Phone 7, iOS4 (iPhone3GS/4, iPad), and Android 2.2 or higher 2.
light is too high, the keystroke recognition may become too sensitive or a “hovering” effect may occur. (Hovering: keystroke is recognized before your finger touches the projection surface.) Therefore, it is necessary to compensate for differences in finger characteristics or operating environment, and this can be accomplished by adjusting the sensitivity of your projection keyboard.
4. Identifying Parts and their Functions. Caution Although this equipment is classified as Class 1 laser product, for your safety, do not directly expose your eyes to pattern projection beams or infrared rays. (1) Projector: Uses a red laser to project the image of a keyboard onto a flat surface in front of the typist. (2) Sensor: Picks up the infrared light reflected off the typist’s fingers and triangulates the location of the reflected light to determine which key was pressed.
Front View Rear View Pattern Projector STRAP LOOP Sensor POWER SWITCH Battery / Bluetooth/ Keyboard/ Mouse/ Charging/ Operating Status LED Battery Charging Full Low Lower LED Red Green Orange HID Searching last device Searching new device Successful pairing Disconnected Upper LED Bright Blue(blinking) Dark Blue(blinking) Bright Blue Blue and Green(alternating) SPP Searching for device Successful pairing Disconnected Upper LED Dark Blue(blinking) Bright Blue Blue and Green(alternating) USB Connected
USB Connection Terminal 1. Purpose: USB device connection or power supply. 2. USB Connector: Standard USB Mini-B type 3. Interface Specification: Compliant with USB HID class specification version 1.11 4. Input Power: 0.5A 5V dedicated DC adapter or USB Bus power from a host device. Bluetooth Connection Switches 1. Bluetooth HID Switch (Top) 2. Bluetooth SPP Switch (Bottom) 20 5. Using the Projection Keyboard This product is used as a keyboard and mouse via Bluetooth HID and USB HID connection. 5.
5.2 Connecting via Bluetooth HID Magic Cube™ supports two types of Bluetooth: •• Connection via Bluetooth HID does not require installation of separate driver. •• Connection via Bluetooth SPP requires installation of diver, in the installation CD. User must identify and use correct Bluetooth profile prior to connection.
This will last 30 seconds. This feature is added for convenience, assuming there is a single host device. ■ Upon successful pairing, Blue LED will stop blinking and become solid blue. If Magic Cube™ cannot locate previously paired host device within 30 seconds, it will delete previously stored connection information and revert to pair mode. •• SPP Mode: Blue LED will blink in intervals, indicating that the device is ready to pair 3.
■ Adjusting keyboard brightness •• Press and hold “FN” key and press right arrow key to increase brightness. •• Press and hold “FN” key and press left arrow key to lower brightness. •• There are three levels of brightness. Default brightness is set at second level during power on. Note FN key is not a repeat key. FN key must be clicked once for each adjustment. 26 ■ Connecting to iPhone and iPad iPhone and iPad connects to Magic Cube™ via Bluetooth HID and a driver is not required.
4) Turn Bluetooth on by tapping the ON button. 6) Locate “Celluon” under Device. 5) iPhone/iPad will now search for pairing device. 7) Select “Celluon” by tapping “Celluon”.
8) A message will pop up “Celluon would like to pair with your phone. Enter the passkey “xxxx” on Celluon”. 9) Type passkey on Magic Cube keyboard and press ENTER. 30 10) Successful pairing is indicated by “Connected” message, and blue LED on Magic Cube™ becomes solid. 11) To turn off Magic Cube™, slide power button to the left. 12) With iPhone/iPad Bluetooth on, Magic Cube™ will connect automatically upon power on.
13) With Magic Cube™ ON from initial connection, iPad/iPhone will connect automatically when Bluetooth is turned back on from host device. 14) Please turn off Magic Cube™ when keyboard is not in use. Note iPhone/iPad OS (iOS4) does not support mouse function. When keyboard does not function with successful pairing, please make sure the device is in keyboard mode. If device is in mouse mode, tap the cursor button located adjacent to spacebar to change back to keyboard mode.
3) Navigate through Android as follows: Home → Main Menu → Settings → Wireless and Network → Bluetooth setting. 34 4) Turn on Bluetooth on Android by checking the box.
5) From the same screen, with Bluetooth ON, tap on Scan devices. 6) Android device will detect “Celluon” and display message “Pair with this device”. 7) Tap on “Pair with this device”. 8) A new message will display on your Android device: “Bluetooth pairing request. Enter PIN xxxxxx to pair with ‘Celluon’.
9) Type passkey on Magic Cube™ and press ENTER. When correct passkey is entered, the Android device is paired. Note Android OS supports mouse function. To switch from keyboard to mouse mode, press and hold “FN” button and tap the cursor button, located adjacent to space bar. To change back to keyboard mode, tap cursor button once. 38 ■ Connecting to PC Windows 7 supports Bluetooth HID and installation of separate driver is not required.
ENTER. 8) Successful paring will be indicated by solid blue LED on the Magic Cube™ device. 9) To turn off Magic Cube™, slide the power button to the left (OFF). 10) Magic Cube™ will connect to host PC automatically when turned back on. Connecting via USB HID for Windows and Mac (Plug-nplay) 1) Connect the host device and Magic Cube™ using miniUSB to USB cable. 2) Turn on Magic Cube™ by slide the power button to the right (ON). 3) Successful connection is indicated by solid green LED.
2. Press and hold FN and tap ‘left’ arrow to lower brightness * Note: There are 3 stages of adjustments. Each adjustments requires repeated steps. Power save mode – 1. Press and hold FN and tap BACK key to disable laser projection 2. To reactivate laser projection, tap in the operation area with 3 fingers (3 fingers must be separated). Switching between keyboard and mouse mode – (Note: default mode is keyboard function) 1.
■ Electrical Characteristics Specification ■ Pattern Projector Item Light Source Keyboard Layout Keyboard Size Specification Red Laser Diode 19mm Pitch, QWERTY Layout Width : 240mm, Height : 100mm 100mm from the Bottom of the keyboard Location Device Project Surface Non-reflective, opaque flat surface Item External Power Supply Battery & Capacity Battery Operating Time Battery Charging Time USB Interface ■ Keyboard Sensor Item Specification Approx.
■ Environmental Conditions Item Operating Temperature Storage Temperature Specification 0 ~ 35°C -5 ~ 35°C (with Batteries included) ■ Dimensions and Weight Specifications Item Size(mm) Weight (g) Specification 38mm x 75mm x 29mm Max. 78 g Celluon, Inc. 46 Ace High-End Tower 918, 235-2 Guro-dong, Guro-gu, Seoul, Korea (152-740) sales@celluon.com , support@celluon.
