Installation Guide

100
gutter warrior lt
Painting Gutter Warrior
™
LT
To paint Gutter Warrior
™
LT to
match the gutter, follow these
instructions.
1. Before installing, clean Gutter
Warrior
™
LT with a mild detergent
or dishwashing liquid. Rinse and
allow to thoroughly dry.
2. Before installing, select the
desired color of gutter coil touch-
up paint or other spray paint
intended for metal surfaces. No
priming is necessary. Spray only
the leading edge of the Gutter
Warrior
™
LT and allow to dry
according to label directions.
3. Install Gutter Warrior
™
LT as
directed.
IMPORTANT: To avoid damaging
the roof and other house components,
it is important to paint only the
front edge of Gutter Warrior
™
LT
BEFORE applying to the gutters.
Installing Gutter
Warrior
™
LT
1. Insert the back of Gutter Warrior
™
LT onto the back of the gutter.
(Fig. 1)
2. Press down hard on the front of
the Gutter Warrior
™
LT until you
hear it “click” into place. (Fig. 2)
3. Make sure that each section of
Gutter Warrior
™
LT overlaps
perfectly. (Fig. 3)
4. To install an outside corner, stop
the section of Gutter Warrior
™
LT
5-8" from the outside corner,
leaving a space to apply the gutter
sealant. (Fig. 4a)
To install an inside corner, stop
the section of Gutter Warrior
™
LT
5-8" from inside corners, leaving
a space to apply the gutter sealant.
(Fig. 4b)
5. Using an end-cap crimping tool,
pinch the back of the Gutter
Warrior
™
LT and the gutter every
3' to stabilize them. (Fig. 5)
6. Cut the Gutter Warrior
™
LT near
the end cap as shown to prevent
water overflow. (Fig. 6)
7. Insert the gutter under the drip
edge (flashing). (Fig. 7)
8. Screw the back of the Gutter
Warrior
™
LT and the gutter into
the fascia board every 24" using
the self-sealing screws. (Fig. 8)
Installing Gutter Warrior
™
LT
in Corners
1. Cut two sections of Gutter
Warrior
™
LT at 45º angles as
shown to create an overlap at the
corner. (Fig. 9)
2. Create an overlap at each square
end while keeping the built-in drip
edge. (Fig. 9, Detail A)
3. Remove the foldover from the
back of the Gutter Warrior
™
LT.
(Fig. 9, Detail B)
4. Fasten both cut sections over the
corner opening with screws.
IMPORTANT NOTES:
•Forinsidecornersandvalleys,
install a water diverter (ASDIV J0)
directly on the Gutter Warrior
™
LT.
•Downspoutsor3"x4" are
recommended in areas with conifer
(pine) trees.
•Theflowfromhigh-levelgutters
must be transferred within
downspouts directly into lower-
level gutters and sealed.
•ToinstallGutterWarrior
™
LT with
longer flashings (2" or more), skip
installation Steps 1 and 5, placing
both the flashing and the Gutter
Warrior
™
LT foldover inside the
gutter.
Fig. 2
CLICK!
Fig. 1
Fig. 3
5-8"
Fig. 4a
5-8"
Fig. 4b
Fig. 5
Before After
Fig. 6
Fig. 7 Fig. 8
Fig. 9
Inside Corner
45
˚
45
˚
BACK
FRONT
OVERLAP
BACK
OVERLAP
FRONT
A. TOP VIEW B. PROFILE VIEW
BEFORE AFTER
OutsideCorner
45
˚
45
˚
gutter warrior