58B Table of Contents 1. 2. 3. 4. 5. 6. 7. Safety Instructions............................................................................. 1 1.1 Work Area Safety .................................................................... 1 1.2 Electrical Safety ....................................................................... 1 1.3 Personal Safety ........................................................................ 2 Description, Specifications and Tool Components.......................... 3 2.
Safety Instructions Work Area Safety 1. Safety Instructions IMPORTANT: To prevent electric shock, fire and/or personal injury or damage, read this user’s manual first and observe the following safety instructions. 1.1 Work Area Safety 6B Always perform automotive testing in a safe environment. Keep your work area clean and well lit. Cluttered benches and dark areas may cause accidents. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
Safety Instructions Personal Safety 1.3 Personal Safety Do not use the tool while tired or under the influence of drugs, alcohol, or medications. A moment of interruption can result in serious personal injury. Do not over-reach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Always wear safety eye protection that meets ANSI standards. Do not wear loose clothing or jewelry.
Description, Specification and Tool Components 2. Description, Components Specifications Description and Tool 2.1 Description 9B The Inspection Camera is an ideal and powerful tool for inspecting difficult-to-reach areas normally hidden from sight. It is a completely digital platform that features the function of capturing and recording photos and videos either on its internal memory or on removable SD cards (not included). The ergonomic tool not only features a 3.
Installation and Connection Zoom, low light vision Image controls 9B 98B Fully adjustable LED Lighting 9B 98B 1m (3') -- expandable to 6m (19') w/optional extensions (not included) Cable reach 103B 102B 8.5mm (0.33") Imager head 9B 98B Imager head and cable to 3m (10') waterproof 107B 106B USB, video out and earphone ports Additonal ports 103B 102B Main unit: 32°F to 113°F (0°C to 45°C); Cable: 14°F to 176°F (-10°C to 80°C) Operating temp. Storage temp.
Installation and Connection Tool Components 2.4 Tool Components Note: Because of continuing improvements, actual product may differ slightly from photo. 10B The Inspection Camera comes with the following items: Fig. 1 LCD Screen – Indicates still images and videos. Cable – Connects to the tool while in use. Cable Connector – Connects the display unit to the imager head and cable. Imager Head – Connects to the cable to view real-time images. Rubber Boot – Protects the tool casing.
Installation and Connection Tool Components Fig. 2 Accessory Magnet – Picks up small metal objects such as dropped rings or screws on the floor. Accessory Hook – Unclogs obstacles and picks up wires in pipes or confined areas. Accessory Mirror – Helps users look around corners and see inside difficult to reach areas. 6) 7) 8) 17B 18B 2.5 Buttons and Ports 12B Fig. 3 A. Power Button – Turns on/off the tool. B.
Installation and Connection Tool Components Trash Can/Reverse Button – Deletes captured photos and videos in the play mode. Pressing again will control the direction of the real-time image and video in the live screen. The real-time image and video will do a horizontal reverse or a vertical reverse. F. LEFT Arrow LED Lighting Adjusting Button – Uses left arrow button to decrease LED brightness in the camera mode. G.
Installation and Connection Accessories Installation 3. Installation and Connection 3.1 The Imager Head and Cable Installation 14B 312B To use the tool, the imager head and cable must be connected to the display unit. To connect the cable to the display unit, make sure the key and slot (Fig. 4) are properly aligned. Once they are aligned, slide the connecting sleeve up to the threads on the cable, and finger-tighten to hold the connection firmly in place. 143B Fig.
Installation and Connection Accessories Installation 3.2 Accessories Installation The three accessories include a magnet, a hook and a mirror (Fig. 2). All are attached to the imager head in the same manner. Hold the imager head as shown in Fig. 5. 14B Fig. 5 Slip the end of the accessory over the tip of the imager head to fix the accessory as shown in Fig. 6. Fig.
Installation and Connection SD Card Installation 3.3 SD Card Installation NOTE: The SD card slot provides for additional memory. The SD card is optional and not included. Different SD cards can be used to insert into the SD card slot. To insert an SD card into the SD card slot, make sure the contacts are facing towards the slot and the angled portion of the card is facing down. When the SD card is installed, a small SD card icon will appear at the top right portion of the screen.
Installation and Connection Video-Out Cable Connection 3.5 Video-Out Cable Connection 16B Insert the video-out cable into the video-out port of the tool and the other end of the cable into the video-in port of a TV. The LCD screen will output a high quality real-time image. 3.6 Earphone Connection 16B Connect an earphone with microphone (optional, not included) to the earphone port of the tool. Speak into the microphone to record your voice.
Battery Charging Precautions Battery Charging Safety 4. Battery Charging Precautions IMPORTANT: To reduce the risk of serious injury, read these precautions and the label on the charger carefully before using. Lithium batteries store a large amount of energy and will vent fire or explode if mistreated. 146B 4.1 Battery Charging Safety 18B Do not probe charger with conductive objects. Do not use the charger if it has been dropped or damaged in any way.
Battery Charging Precautions Charger Inspection 4.3 Charger Inspection CAUTION: Before using, inspect the charger and correct any problems. Set up the charger according to these procedures to reduce the risk of injury from electric shock, fire and other causes, and to prevent tool damage. 1) Make sure the charger is unplugged. Inspect the power cord and charger for damage or modifications, or broken, worn, missing, misaligned or binding parts.
Battery Charging Precautions Battery Charging Procedures Fig. 8 There are two means of charging battery: 1) To charge the battery with the charger: Locate the DC power source port of the tool. With dry hands, connect the tool to the charger and plug in the charger to start charging. 2) To charge battery by USB cable: Locate the USB port of the tool. With dry hands, connect the tool to a PC with the USB cable to start charging. The battery will begin charging automatically.
Operation Instructions Basic Operation 5. Operation Instructions 3B IMPORTANT: Always wear safety eye protection to protect your eyes against dirt and other objects. Follow the operation instructions to reduce the risk of injury from electric shock, entanglement and other causes. 190B 5.1 Basic Operation 2B NOTE: When in operation, the cable can be bent into a specific shape. This may help to maneuver the cable into confined areas.
Operation Instructions Operation Precautions 12) Connect the optional earphone with microphone to the earphone port of the tool. Speak into the microphone to record your voice. 5.2 Operation Precautions Use the tool only as directed. Do not operate the tool unless the user’s manual has been read thoroughly and proper training has been completed. The display unit is not waterproof. The imager head and cable are waterproof, but not acid-proof or fireproof.
Operation Instructions Tool Inspection breakage and any other condition which may affect its operation. Use only accessories that are recommended by the manufacturer for the tool. Dry your hands before operating the tool or charging the battery. Always use appropriate personal protective equipment while handling and using the tool.
Operation Instructions Tool and Work Area Set-Up Turn on the power and make sure the tool starts up as described in the Basic Operation section. If the tool does not work well after turning it on, have the tool checked by a qualified technician. Any tool that cannot be controlled with the power button is dangerous and must be repaired. 218B NOTE: Please check following methods to avoid injury.
Operation Instructions Tool and Work Area Set-Up 3) 4) Check if any liquids will be contacted during inspection. The imager head and cable are waterproof to a depth of 3m (10'). Greater depths may cause leakage into the imager head and cable and cause electric shock or damage the tool. The display unit is not waterproof and should not be exposed to wet conditions. Check if any chemicals are present, especially in the case of drains. Chemicals may damage the tool. Check the temperature of the area.
Operation Instructions On Screen Navigation 5.5 On Screen Navigation 25B 1) Splash Screen When the tool is powered on, the first screen displayed is referred to as the splash screen. (Fig. 9) This screen tells you the tool is booting up. Once the tool is fully powered up, the screen will automatically switch to the live screen. 251B Fig. 9 2) Live Screen The live screen is where you will do most of your work. A live image of what the imager head sees is displayed on the screen.
Operation Instructions On Screen Navigation Fig. 10 5) Zooming Press the UP and DOWN arrow buttons while in the still camera mode to zoom in or out. A zoom indicator bar will be displayed on the screen as you adjust the zoom. (Fig. 11) 259B 260B Fig. 11 256B 6) Entering the Primary Settings Screen Pressing the Setting button while in the live screen will take you to the primary settings screen. (Fig. 12) Pressing the Back button at any point will take you back to the live screen. 261B 26B Fig.
Operation Instructions 7) On Screen Navigation Capturing a Photo When in the live screen, make sure the camera icon is present at the top left portion of the screen. (Fig. 13) Press the OK button to capture a photo. The image is saved to the internal memory or SD card. The total number of photos is displayed below the camera icon. The number will increase or decrease as different capacity SD cards are used, or the photo quality is adjusted. 264B Fig.
Operation Instructions On Screen Navigation video, you are recording simultaneously. It may take a few seconds to save the captured video to the internal memory or SD card. 9) Playing Back and Deleting Captured Photos and Videos Press the Play button on the key pad to display two modes for you to select. Photos and videos that were captured will be displayed on the screen. Use the LEFT and RIGHT arrow buttons to move from Photo mode to Video mode. (Fig. 15 and Fig. 16) 267B Fig.
Operation Instructions On Screen Navigation While in the photo mode, select a photo and press the OK button. A bar will appear with record mode in the middle of the screen. (Fig. 17) 2 Fig. 17 Inserting the optional earphone with microphone and pressing OK button will begin recording (Fig. 18) and timing. Fig. 18 Press the OK button as desired to stop recording and then the“ ” icon will appear. Press the OK button to play the recording.
Operation Instructions On Screen Navigation recording. Press the LEFT button to fast forward recording and the RIGHT button to reverse the recording. Press the UP button to stop playing the recording. Either in the Photo mode or in the Video mode, press the Trash Can button to delete captured photos and videos, and a “Are you sure you want to delete this file?” message appears on the screen. (Fig. 22 and Fig.
Operation Instructions On Screen Navigation While in the Primary Settings Screen (Fig. 12), select Advanced Settings from Setup and then press OK button, you will enter the secondary settings screen (Fig. 25) where you can set the Date and Time, Restore Defaults and select a Language as needed. Press the Back button at any point to go back to the primary settings screen and press it again to go back to the live screen. 27B Fig.
Operation Instructions Icons 5.6 Icons 1) 2) 3) Battery Capacity - Fully charged battery. 273B 278B SD Card - Indicates an SD card has been inserted into the tool. 274B 278B Still Camera - Indicates the tool is operating in still camera mode. 275B 278B 4) Video Camera - Indicates the tool is operating in video camera mode. 5) Record sound - Push OK to record sound in the photo play mode. 278B 278B 6) 7) Record - Press OK to record in the photo record mode.
Operation Instructions 11) Advanced Settings Advanced settings Advanced Settings is the default mode from the Setup menu. Press the Setting button to enter Setup. Fig. 26 Select Advanced Settings from Setup and press the OK button to modify advanced settings. Fig. 27 12) 278B When necessary, use the UP and DOWN arrow buttons to select Date and Time, Restore Defaults and Language from Advanced Settings. – Displays color or black/white. Color is the default mode.
Operation Instructions Advanced Settings Fig. 28 Use the LEFT and RIGHT arrow buttons to select from Color mode to Black/White mode, then press the OK button to save your selection. If you wish to view or capture color images and videos, select Color from Setup. Fig. 29 If you wish to view or capture black/white images and videos, select Black/White from Setup. Fig. 30 13) 278B – Asks if format media.
Operation Instructions Advanced Settings Select Format Media from Setup and press the OK button. Fig. 31 If you wish to format media, select Format Media from Setup and press the OK button and then use the LEFT and RIGHT arrow buttons to select Yes, then press the OK button to save your selection. Fig. 32 If you do not wish to format media, use the LEFT and RIGHT arrow buttons to select No to return to the previous menu. Fig.
Operation Instructions Advanced Settings files in memory” appears on the screen. Press the OK button to save your selection and return to the previous menu. Fig. 34 If you do not wish to format media, select No to return to previous menu. Fig. 35 14) 280B – Displays firmware version. Select Help from Setup and press OK button to display Firmware Version. Fig.
Operation Instructions Advanced Settings Fig. 37 – Sets date and time. 15) 281B When you enter Advanced Settings, select Date and Time and press the OK button. Fig. 38 Use the UP and DOWN arrow buttons to set the exact date and time while using the LEFT and RIGHT arrow buttons to move from one item to another and press the OK button to save. Fig. 39 16) 28B – Ask to restore factory defaults.
Operation Instructions Advanced Settings OK button. Fig. 40 If you wish to restore factory defaults, use LEFT and RIGHT arrow buttons to select Yes, then press the OK button to save your selection. Fig. 41 If you do not wish to restore factory defaults, select No to return to the previous menu. Fig. 42 17) 28B – Displays multi-language interface.
Operations Instructions Advanced Settings English is the default language. Select Language from Advanced Settings and press the OK button. Fig. 43 Use the LEFT and RIGHT arrow buttons to switch among English, Spanish, French, German and Dutch. Select the desired language and press the OK button to save your selection. Fig.
Troubleshooting 6. Troubleshooting POSSIBLE REASONS Cable connection is loose. SYMPTOMS SOLUTIONS 285B 284B 286B Check and reattach. 28B Display is on, but does not show image. 289B 287B Imager head is covered by debris. Inspect imager head and clean if needed. Low battery. Charge battery. 291B 290B LEDs on imager head are dim at max brightness, display changes between black and white, and/or the color display turns itself OFF after a short period. 29B The tool will not turn on.
Parts List and Diagram 7.
Parts List and Diagram 37
