Laser In-Line Air Shear 65706 Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
Save This Manual CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
b. Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The tool is able to create sparks resulting in the ignition of the dust or fumes. c. Keep bystanders, children, and visitors away while operating the tool. Distractions are able to result in the loss of control of the tool. Personal safety a. b. c. d. Stay alert. Watch what you are doing and use common sense when operating the tool.
safer at the rate for which the tool is designed. c. d. Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the tool from the air source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool unintentionally.
Symbols and Specific Safety Instructions cannot be built into this product, but must be supplied by the operator. 2. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) 3. Obey the manual for the air compressor used to power this tool. 4.
physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between different processes. 5. Include vibration-free periods each day of work. 6.
Functional Description • This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up.
operation. Add a few more drops after each hour of continual use. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a connector and quick coupler, will make operation more efficient, but are not required. WARNING! To prevent serious injury from accidental operation: Do not install a female quick coupler on the tool.
Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired.
General Operating Instructions 1. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use. 2. Mark the line you want to cut on the work material. Since this tool removes 7/32” of material as it cuts, allow for this when marking the cut line. 3. Secure the work piece to the work table using clamps or other suitable fasteners. 4.
User-Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment.
If the Laser Light ceases to function, check the batteries. Problem Troubleshooting Possible Causes Decreased output. 1. Not enough air pressure and/ or air flow. 2. Obstructed trigger. 3. Incorrect lubrication or not enough lubrication. 4. Blocked air inlet screen (if equipped). 5. Air leaking from loose housing. 6. Mechanism contaminated. 7. Vane wear or damage. Housing heats during use. 1. Incorrect lubrication or not enough lubrication. 2. Worn parts. Severe air 1. Cross-threaded housing leakage.
Parts List Part # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description Housing Valve Plug O-Ring Spring Valve Spindle O-Ring Valve Spindle Pin Trigger End Plate Cap Ball Bearing Rear End Plate Rotor Blades Rotor Pin Cylinder Front End Plate Ball Bearing Washer Idler Gear QTY.
ASSEMBLY DIAGRAM SKU 65706 For technical questions, please call 1-800-444-3353.
90 day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.