THREE-PIECE AIR NAILER KIT 98464 Set up and Operating Instructions ITEM 97526 ITEM 97524 ITEM 97520 Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
Save This Manual NOTICE is used to address practices not related to personal injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
sure to high intensity noise is able to cause hearing loss. Personal safety a. b. c. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts.
g. h. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. Use only accessories that are identified by the manufacturer for the specific tool model. Use of an accessory not intended for use with the specific tool model, increases the risk of injury to persons. b.
cal known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Symbol Definitions Symbol Property or statement WARNING marking concerning Risk of Explosion. 3. Only use with accessories rated to handle the forces exerted by this tool during operation. Other accessories not designed for the forces generated may break and forcefully launch pieces. 4. Do not load nails with the trigger or safety depressed.
toxic. When stapling or nailing these materials extra care should be taken to avoid inhalation and minimize skin contact. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. Hold Nailer away from head and body. During operation the Nailer may kick back causing injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4.
Functional Description Specifications for 97526 Air Pin Nailer Air Pressure Range 60-100 PSI Maximum Air Pressure 120 PSI Air Inlet 1/4” -18 NPT Air Consumption 5.
operate accidentally after the air supply is disconnected. Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. 1. Incorporate an in-line oiler, shut-off valve, regulator with pressure gauge, and filter for best service, as shown in the diagram above. An in-line shutoff valve is an important safety device because it controls the air supply even if the air hose is ruptured. 3.
discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Testing The Single Sequential Safety Trip Mechanism Even though the nailer should be empty during this procedure, always point the nailer/Stapler at a piece of scrap wood when testing. 1.
Release the trigger and squeeze it Loading the 97520 Air Brad Nailer again. The tool must cycle (fire) once only. With the Trigger held, carefully lift the nailer and press it against the workpiece again. The tool must not cycle (fire). If it fails to 1. ALWAYS wear ANSI-approved impact safety gogact in the manner explained in bold, gles when reloading or doing any have it repaired by a qualified service other maintenance on this tool. technician.
2. Insert the brad nails into the Magazine, letting the pointed end ride on the rail of Magazine B (61A). If loading staples, fit the crown of the staples so they fit over, and ride on the rail of Magazine 8. B (61A). 3. After the nails or staples reach the nose of the tool, close Magazine A (67A). 4. Note: The window gauge on Magazine A (67A) lets you know how many nails or staples remain. General Operating Instructions for All Three Nailers 1.
To prevent serious injury from accidental operation: Release trigger, detach the air supply, and safely discharge any residual air pressure in the tool before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise, vibration, or any leakage is detected, have the problem corrected before further use.
To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise, vibration, or any leakage is detected, have the problem corrected before further use. nected and is incapable of firing any Brads. 8. With the Driver Guide Cover (52A) facing away from you, push the Lock Spring (92) and remove Driver Guide Cover. 9. Remove the jammed Brad. 10. Close the Driver Guide Cover (52A), making sure it locks in place. Cleaning, Maintenance, and Lubrication 11.
away from you and any other people or fragile objects - see Figure 1. technician. 6. FIGURE 1 Remove all three Safety Cover Bolts (53) on the Safety Cover (54) - see Figure 2. FIGURE 2 Lightly oil the Driver (17A) and replace the Driver Cover (57) with the tab in the Cover facing the Driver Guide (58). Replace the Safety Cover (54), being careful to line up the bolt holes and fit the Safety (52) into the slot. Replace and securely tighten all of the Safety Cover Bolts (53).
To prevent Clearing Jams for 97526 Pin Nailer serious injury from accidental operation: Release trigger, detach the air 1. ALWAYS wear supply, and safely discharge ANSI-approved impact safety any residual air pressure in goggles when clearing jams. the tool before performing any inspection, maintenance, or 2. In case of a fastener jam, take your cleaning procedures. finger off the Trigger (27). Rotate the Trigger Lock/Safety (60) clockwise To prevent serious or counter-clockwise.
Maintenance (For All Nailers) 1. Daily - Air Supply Maintenance: Every day, perform maintenance on the air supply according to the component manufacturers’ instructions. The lubricator’s oil level needs to be maintained and the moisture filter must be regularly drained. Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce wear on the tool. 2.
Troubleshooting Guide Stop using the Nailer/Stapler immediately if any of the following problems occur. Repairs and part replacements must be done only by a qualified technician. All procedures in bold on this chart are to be attempted only be a qualified technician. Problem Likely Cause Solution Air leaking at Trigger area. O-Rings in Valve Body are damaged. Replace O-Rings and check contact trip operation. Air leaking between Housing and Nose. 1. 2. 1. 2. 1. 2. 3. Loose screws in Housing.
PARTS LIST FOR 97526 Air Pin Nailer Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Description Hex Bolt Deflector Seal Spring Head cap O-RIng O-RIng Head Valve Piston O-Ring O-Ring Piston-Driver Unit Lining Ring O-Ring Cylinder Bumper O-Ring Body Nozzle Seal Trigger Valve Head Trigger Plunger O-RIng O-Ring Trigger Valve Guide Spring E-Ring Trigger Retainer Pin Hex Bolt Washer Pusher Unit SKU 98464 Q’ty Part 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
ASSEMBLY DIAGRAM FOR 97526 Air Pin Nailer SKU 98464 For technical questions, please call 1-800-444-3353.
PARTS LIST FOR 97520 Air Brad Nailer SKU 98464 For technical questions, please call 1-800-444-3353.
ASSEMBLY DIAGRAM FOR 97520 Air Brad Nailer SKU 98464 For technical questions, please call 1-800-444-3353.
PARTS LIST FOR 97524 Air Nailer/Stapler Part SKU 98464 Description 1 Exhaust Deflector 3 4 5 6 7 8 9 10 11 12 13 14 Hex.
ASSEMBLY DIAGRAM FOR 97524 Air Nailer/Stapler SKU 98464 For technical questions, please call 1-800-444-3353.
Limited 1 Year warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).