User's Manual

ManualsBrandsCentraLite Systems ManualsElectronicsZigbee Appliance Module

ZIGBEE HA Appliance Module

4255050-RZHA

Rated: 120 VAC, 60Hz

Rated 1200W Incandescent, 1200VA Fluorescent,

10A Resistive and 1/2 HP Motor loads @ 120V AC

Warnings and Cautions:

 To be installed and/or used in accordance with appropriate electrical codes and regulations.

 If you are unsure about any of these instructions, consult a qualified electrician.

 Unplug unit when servicing connected appliances.

 Save this instruction sheet. It contains important technical data along with testing

and troubleshooting information which will be useful after installation is complete.

INTRODUCTION

The CentraLite ZIGBEE HA Appliance

Module uses the Zigbee Home Automa-

tion(HA) communication protocol to link

with other Zigbee HA devices. Each

Appliance Module acts as a router for

messages sent through the Zigbee net-

FEATURES

 Status LED

 Load control from button on appliance module

 Ease of installation

 Compatible with other Zigbee HA certified level

controllers

INSTALLATION

STEP 1

Attach the plug from the appliance to be

controlled into the receptacle of the

Appliance Module.

STEP 2

Attach Appliance Module to wall recepta-

cle. Secure using the locking tab at the

top of the module if necessary. Verify

that the receptacle is powered. If the

receptacle is powered by a wall switch,

the switch must be kept ON at all times.

STEP 3

To join the ZIGBEE HA Appliance Mod-

ule to a certified HA controller be sure

that the HA controller is open for joining.

If the Appliance Module has not been

joined to a network then press the Appli-

ance Module button. The Appliance

Module will then attempt to join an open

HA network.

Upon a successful joining of the Appli-

ance Module to a Zigbee HA network the

status LED will blink 2 times. When the

appliance module powers up after being

joined to a Zigbee HA network, it will

4255050-RZHA

STEP 3 cont’d

If the Appliance Module will not join a

Zigbee HA network then:

 Make sure the Appliance Module is

powered up

 Ensure the Appliance Module is

within RF range of a routing device

 Make sure the target Zigbee net-

work is open for joining

STEP 4

Once the Appliance Module is joined to

the Zigbee HA network, use the certified

HA controller to configure the Appliance

STEP 5

If it becomes necessary to remove the

Appliance Module from a Zigbee HA

network then you must factory default the

Appliance Module. To factory default the

Appliance Module:

 Remove the Appliance Module from the

wall receptacle

 Press and hold the Appliance Module

button

 Reinstall the Appliance Module into the

wall receptacle while holding the button

 You will see the status LED turn ON

 Once the LED is ON let go of the button

 The Appliance Module will now be reset

to factory defaults and ready to join to a

Zigbee HA network.

Summary of content (2 pages)

PAGE 1
ZIGBEE HA Appliance Module 4255050-RZHA Rated: 120 VAC, 60Hz 4255050-RZHA Rated 1200W Incandescent, 1200VA Fluorescent, 10A Resistive and 1/2 HP Motor loads @ 120V AC Warnings and Cautions:   To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any of these instructions, consult a qualified electrician.
PAGE 2
ZIGBEE HA Appliance Module 4255050-RZHA Rated: 120 VAC, 60Hz 4255050-RZHA Troubleshooting If the Appliance Module is not working properly, proceed with the following steps:  Make sure the device is being supplied with a 120V, 60 Hz AC source.  Check the load that is being controlled. Is the appliance fixture turned on?  Make sure the controlled load does not exceed 10 AMPs.