Hummingbird Elite 3D Pro Instruction Manual SPECIFICATIONS This Super-Micro R/C helicopter has the most advanced capabilities and is considered topof-the-line. 120 degree eCCPM control, collective main and tail rotors, torque tube tail drive and brushless motor ensure top performance. MOTOR SIZE: MAIN ROTOR DIAMETER: LENGTH: WEIGHT: 4100 RPM/Volt 520mm 485mm 360-380g with electronics and battery Century Helicopter Products Designed and Developed in USA Copyright February 2005. All rights reserved.
Introduction Thank You For Choosing The Hummingbird Elite 3D Pro Helicopter From Century! Required Items Introduction Congratulations on the purchase of Century Helicopter Product’s Hummingbird Elite series helicopter. The Hummingbird Elite is not only ideal for beginners new to the hobby, but also for the intermediate to expert pilot looking for the ultimate in micro electric helicopter performance. The 3D Pro requires a 6+ channel computer radio that supports 120 degree eCCPM operation.
Your New Elite 3D Pro Helicopter Getting Started Section 1 CHECKING OVER THE MODEL Ex tr as Extr tras Before beginning, check the kit contents. This is a good time to check the “required items” section on page 2 and make sure everything necessary is on hand for assembly. Some items that are packaged with the helicopter are not attached to the helicopter. This will include main blades and bolts, antenna tube, tools, servo tape and some fasteners.
Connection And Diagnostics For The Electronic Components Section 3 Speed Control Connection TESTING AND PREPARATION OF RADIO EQUIPMENT 6 5 4 3 2 1 Channels Aileron, Elevator & Pitch Servo Connection 654321 Channels Ch#1 Aileron Ch#2 Elevator Ch#6 Pitch (CP) IMPORTANT: ! All connections shown in this manual work for Futaba & Hitec radio systems. If you have any other radio system please consult your radio instructions for channel numbering. (some equipment may differ in appearance.
Servo Installation And Pushrod Setup For The 3D Pro Section 5 MOUNTING YOUR SERVOS (USE SECTION 4 FOR DETAILS) 1. Insert the pushrod into the hole on the servo arm farthest from the output (10-12mm from center). 1 3 2 2. Place servo tape on the mounting surface before mounting the servo. 3. Note that the elevator servo is mounted slightly forward (3mm or so). This will ensure that the arm can move freely (avioding contact with the frame). 4 4.
Section 6 eCCPM Radio Setup Expert Tips: To make the setup go easier on transmitters with 5 or more programmable points on the pitch curve, assuming that the 5 points correspond to low stick, point 1, point 2, point 3 and high stick. Set points 1,2,3 to 50% which will create a flat pitch curve in the center that will allow you to consistently find 50% pitch near mid stick. After servo direction and centering is completed, return points 1 & 3 back to their default values.
Section 8 Tips, Blade Tracking, Q & A ROUTING THE ANTENNA To provide the best possible reception for the model, the Hummingbird Elite comes with a plastic tube for routing the antenna. Put a small hole in one end and pull the antenna all the way through leaving about 2 to 3 inches of slack. Wrap the antenna around the tube. After the antenna is almost completely wrapped around the plastic tube place a hole at the other end of the tube to secure the end of the antenna.
Section 9 The First Flight BASIC HOVERING Hovering When all is set, ready and checked, it’s time for the initial flight. Try setting aside a 5 foot diameter circle as a takeoff and landing pad. Keeping the helicopter inside the landing are will help improve your training. 1. Turn the transmitter on first! Turn helicopter on (plugging in the battery) and stand behind the model about 10 feet away. 2. Always watch the nose of the helicopter, move the rudder left and the nose will move left. 3.
Section 10 Construction Diagram WARRANTY INFORMATION Your new equipment is warranted to the original purchaser against manufacturer defects in material and workmanship for 30 days from the date of purchase. During this period, Century Helicopter Products will repair or replace, at our discretion, any component that is found to be factory defective at no cost to the purchaser. This warranty is limited to the original purchaser and is not transferable.
Section 11 CNE201 Head Axle & Dampeners Replacement Parts & Upgrades CNE207 Flybar Paddles CNE216 Antirotation Bracket CNE213 CNE250 Auto Rotation Hub & Gear Main Shaft Bearings (3x6mm -2pc-) CNE209A Swashplate Links CNE213F Bottom Plate Flanged Bearing (Flanged 3x6mm -1pc-) CNE306 Seesaw Assembly CNE312 Top Motor Plate CNE318 Tail Rotor Shaft Assembly CNE324 Tail Blade Grip Set with Bearings CNE301 Motor Mount CNE307 3D Pro Head links CNE313 Main Shaft, Spacers & Collar CNE319 Inner tail C
