C4000XG USER GUIDE Version 1.
NOTICE This document contains confidential information, which is proprietary to CenturyLink. No part of its contents can be used, copied, disclosed, or conveyed to any party in any manner whatsoever without prior written permission from CenturyLink. Copyright © 2019 CenturyLink Inc. All Rights Reserved.
Contents 1 Introduction ........................................................................................................................................................................................................................ 4 2 Overview ............................................................................................................................................................................................................................. 4 3 Setup .....................
1 Introduction Please read through this user guide prior to using this product and retain the manual for future use. Only operate this device upon the full understanding of the devices basic operation as described in this manual. Any deviation or alteration of this product, it's appearance or specification are without consent or further notice of the company. 2 Overview The C4000XG is a high performance 4x4 Wi-Fi 6 router (802.11ax) that with a four-port built-in it Giga Ethernet switch.
3.
4. Plug other end of Ethernet cable into the CenturyLink support connections (ONT) or wall jack. or 5. Continue to the Internet connection Setup.
4 Internet Connection Setup (CenturyLink Home Router side) Your C4000XG can automatically detect and configure your Internet (section 4.1), or done manually (section 4.2). 4.1 Automatic Connection 1. Open your web browser to a website. Wait while your device tries to detect your DSL connection to your ISP. This may take a few minutes. 2. After it detects the connection, the LED Ring will show green on your C4000XG when the Internet is ready for you to use.
3. The main screen will appear. Click the quick setup icon to configure the device’s Internet access 4. Enter the user name and password provided by your ISP. Click Apply to finish the configuration.
5. The LED ring in the center of the C4000XG will light up green upon full internet access. If it is Red, please contact CenturyLink support to troubleshoot. Alternatively, you can look at the status within the Web UI to try to determine what the issue might be.
5 Setting up a wireless network You can setup a wireless network using the following methods using an automatic connection (section 5.1) or manually connecting the device (section 5.2): 5.1 Using WPS (Wireless Protected Setup) 1. Press the WPS button on the C4000XG’s front for more than five seconds to turn WPS on. 2. You should see the light blinking White until a pairing sequence has started with the device connecting to the network (at which point it will alternate white and green). 3.
6 Getting to know the C4000XG Front LED RING WPS BUTTON Back USB PORT ETHERNET PORTS WAN/LAN PORT SFP+ CAGE RESET & POWER PORTS 11
7 Technical Specifications: 7.1 General Specifications Model Number: C4000XG Standards: Memory: IP: Speed: 802.11n/ac/ax, and backward compatible to 802.11a/b/g 1GB DDR3 Memory, 1GB Flash IP versions 4 and 6 Wireless LAN PHY Rate: 2.4 GHz: 802.11ax - up to 1200Mbps 5 GHz: 802.11ax - up to 4800Mbps Wired LAN Ethernet: Wired WAN Ethernet: 10/100/1000 Mbps auto-sensing SFP+ Cage: See CenturyLink support website for supported modules SFP+ Cage. 7.2 Dimensions and weight Gateway (unit only) Size: 8.
Storage Temperature: -20° C to 85° C (-4° F to 185° F) Operating Humidity: 8% to 95% (non-condensing) Storage Humidity: 5% to 100% (non-condensing) 8 FCC: Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 34cm between the radiator & your body.
