Installation manual

ManualsBrandsCervis ManualsRemote ControlTM70

Table Of Contents

FCC Statements
Table of Contents
List of Figures
List of Tables
Cervis Inc. Safety Precautions
- 1.1 What You MUST Do
- 1.2 What You MUST NOT Do
2.0 TM70 System Description
- 2.1 TM70 System Specifications
3.0 CB70 Battery Charger and BT24IK Batteries
- 3.1 Charging Tips
4.0 Receiver
5.0 Starting Up
6.0 Operating Instructions
- 6.1 Using the System
- 6.2 General Instructions
- 6.3 Transmitter Power Monitoring
7.0 Maintenance
- 7.1 Fault Identification
  - 7.1.1 Transmitter
  - 7.1.2 Receiver
- 7.2 Returning Equipment for Repair
8.0 Warranty
9.0 Parts Information
10.0 Programming a Spare Transmitter
11.0 Program the Machine ID in LCD Transmitters
12.0 Change Base Channel
13.0 CANopen Interface v2.4
- 13.1 Introduction
- 13.2 CAN Bus Connection
- 13.3 Bus Termination
- 13.4 Transmitter Data Dictionary
- 13.5 Pushbuttons and Console Box PDOs
- 13.6 Receiver Data Dictionary
- 13.7 Receiver Signaling
- 13.8 TM70 CAN Receivers
14.0 LCD70 Display Option
- 14.1 Functional Description
- 14.2 Internal Connection
  - 14.2.1 Power Supply and I2C Bus
  - 14.2.2 Range Limiter
- 14.3 LCD70 Display Operating Modes
- 14.4 Data Feedback Operating Mode
  - 14.4.1 Multiple Returns/Multiple Feedback
- 14.5 ASCII Character Map
- 14.6 Available Icons
- 14.7 VT100 Display Control
  - 14.7.1 Control Characters
  - 14.7.2 Valid Control Sequences
15.0 First Come – First Served Operation
16.0 LA70 and LA70M Range Limiter
- 16.1 Infrared Sensor
- 16.2 Infrared Transmitter
- 16.3 Installation
- 16.4 LA70 Technical Characteristics
- 16.5 LA70M Infrared Transmitter
- 16.6 Working Zone
17.0 Tandem Operation
- 17.1 Single Master Transmitter Systems
- 17.2 Two Master Transmitter Systems
18.0 TM70 Analog Feedback Calibration
- 18.1 LR71/72 and IN0-10V Assembly
19.0 IN0450P Option
- 19.1 Description
- 19.2 IN0450P and LR70 Assembly
20.0 IN4D Option
- 20.1 Description
- 20.2 IN4D and LR71/LR72 Assembly
21.0 INCAN Option
- 21.1 INCAN Connections and Configuration Jumpers
22.0 A1P4RCAN Option
- 22.1 A1P4RCAN Connection and Jumper Configurations
23.0 A2ICAN Option
- 23.1 Response Curve
- 23.2 Ramp Speed
- 23.3 PWM Current Output Features
- 23.4 A2ICAN Connections and Jumper Configurations
  - 23.4.1 LR72 Connections
- 23.5 Outputs
  - 23.5.1 Output PWM1
  - 23.5.2 Output PWM2
- 23.6 ISP (In-Circuit/In-System Programming)
24.0 A2VCAN Option
- 24.1 Output Response Curves
- 24.2 Ramp Speed
- 24.3 Pulse Width Modulation (PWM) Specifications
- 24.4 A2VCAN to LR72 Connections (see Figure 51)
- 24.5 A2VCAN Voltage Outputs
  - 24.5.1 Output 1 (VO1) (see Figure 51)
  - 24.5.2 Output 2 (VO2)
- 24.6 ISP (In Circuit/In-System Programming)
- 24.7 A2VCAN Power Supply Board POT70V4
25.0 Tele-Alignment Option
- 25.1 Tele-Alignment Process
- 25.2 Menu 3.1 Adjust
26.0 R70/Plus Receivers – Software V3.2 Compatible
- 26.1 Detail Characteristics
  - 26.1.1 V3.2 TM70 Software Features
  - 26.1.2 V3.2 Software Compatible Hardware
- 26.2 Internal Wiring
27.0 i-Kontrol Console Box
- 27.1 i-Kontrol Console Remote Description
- 27.2 i-Kontrol Specifications

TM70/3-10 & i-Kontrol Console RC System

U035.3-TM70_Console_Sys

19.2 IN0450P and LR70 Assembly

Figure 37. IN0340P and LR70 Assembly

Cod-2303758

IN0450P

Cod. 1131026 (x4)

Cod. 1135024 (x2)