GPS-208 USER MANUAL CES WIRELESS TECHNOLOGIES, CORP. 925-122 South Semoran Boulevard Winter Park, Florida 32792 GPS208 Manual v1p1.doc Revision 1.1 November 1, 2011 © Copyright CES WIRELESS TECHNOLOGIES CORP. (2011) The information contained in this document is subject to change without notice and should not be construed as a commitment by CES WIRELESS TECHNOLOGIES CORP. unless such commitment is expressly given in a covering document.
REGULATORY COMPLIANCE FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits pursuant to Part 15 Subpart B, Part 22, and Part 24 of the FCC rules.
Precautions • • • • • • • • • • • • • • • • • • • • • • Read this entire manual and the label on the exterior of the battery. Keep the battery away from sources of excessive heat such as fire, stoves, or direct sunlight. Keep the battery away from sources of high voltage or static discharge. Do not use or store the battery with other batteries or where it could touch metal. Do not put the battery into a microwave oven. Do not allow the battery to be crushed. Keep the battery away from children.
CHANGE LOG Date 09/20/11 11/01/11 Author Doug Hamilton Doug Hamilton Description Initial Release (1.
Table of Contents REGULATORY COMPLIANCE ........................................................................................................................................2 FCC................................................................................................................................................................................... 2 RF EXPOSURE..........................................................................................................................................
1.0 Introduction The GPS-208 is one of the smallest and most economical GPS asset tracking devices available today. The devices is neither weather, dust or splash proof. GPS and event data is made available on-board the GPS-208 for transmission to FleetLinc (CES web based subscriber fleet management service). The GPS-208 can also be licensed for use with POWER-trak3™ PC/Server software. Please contact CES for further information on this. 1.
USR2 (Blue) – This LED indicates the state of the GPS fix. If illuminated the GPS206 has established a position fix from satellites in the GPS satellite constellation that are viewable from its current location. Figure 1: Front view of the GPS-208 1.7 Label The GPS-208 has a printed label on its top side. It is important that when the GPS-208 is mounted that the label side is pointing towards the sky.
2.0 Specifications Note: Specifications subject to change without notice. 2.1 System Information Dimensions Weight Housing: TX Power: 3.23 x 1.81 x .83 inches (82 x 46 x 21 mm) Rugged textured plastic enclosure, V0 fire rated Class 4 (2W @850/900 MHz) Class 1 (1W @1800/1900 MHz) 850/900/1800/1900 Frequency: 2.2 GPRS Packet Data Mode: Protocol: Coding Schemes: Packet Channel: 2.3 GPS Functionality Antenna: 2.4 Built In Environment Operating: Storage: Humidity: Vibration: 2.
3.0 Installation The instructions in this section describe the hardware installation of the GPS-208. To install the GPS-208 in a vehicle follow these steps: • • • Choose a convenient location in the vehicle – either in the trunk or interior of a vehicle. Avoid locations that might expose the GPS-208 to excessive heat or moisture. The GPS-208 as a printed label on the top side of the device. It is important that this label be facing towards the sky when the GPS-208 is installed.
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Functionality N/A N/A Ignition Sense N/A N/A Ground N/A Output 1 N/A N/A Power Input (9-16 VDC) N/A Input 1 Output 2 Input 3 Input 2 HRNS062 Color Codes No Connection No Connection White No Connection No Connection Black No Connection No Connection No Connection No Connection Red No Connection No Connection No Connection No Connection No Connection HRNS063 Color Codes No Connection No Connection White (Cable 1) No Connection No Connection Black (Cable 1 &
Figure 5: Opening the enclosure of the GPS-208 2) Apply gentle pressure upwards on the lever until the lid snaps open. Figure 6: Enclosure unsnapped on the GPS-208 3) Carefully slide the cover off of the GPS-208. 3.2.2 Closing the GPS-208 To close the GPS-208 place the cover onto the base as shown in Figure 6. Carefully slide the lid until it snaps into place. 3.3 Installing the SIM (Subscriber Identity Module) Card The SIM card is an integral part of any GSM terminal device.
Figure 7: Internal view of the GPS-208. Note the orientation of the SIM card. NOTE: Always take care to protect the SIM card. The GPS-208’s GSM/GPRS related functionality will not operate without the SIM card installed. Ensure the power to the GPS-208 is disconnected before inserting the SIM card. Failure to do so might result in an unusable GPS-208 or a damaged SIM card. 3.4 Connecting Power The GPS-208 has an input voltage range of 9-16 VDC.
• • 3.5 Connect the ignition wire of the GPS-208 to an auxiliary power source, i.e. ignition. Device goes through a reset upon ignition on. Optional Backup Battery An optional 230 mAH backup battery is available for the GPS-208. The battery may need to be connected during the installation process. The battery will need to be turned on via the power switch (see Section 3.0 for more information). Figure8:9:GPS-208 GPS-208optional optionalbackup backupbattery batteryconnected and Figure to the connector.
4.0 Support If you need help, we are easily accessible …. Telephone: Call 407-679-9440, and ask for product support. Fax: 407-679-8110 Email: support@ceswireless.com Skype: Please email support@ceswireless.com to obtain your currently assigned support engineer’s Skype address. Product support may ask you to E-MAIL a copy of the programmed parameters to us for analysis. To do this, go to FILE on the DP-1000S main menu, and click on SAVE AS. Note the path to the saved file in the save file dialog.
