INSTRUCTION MANUAL CZ 75 SP-01 SHADOW
Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in accidental discharge and cause injury, death or damage to property. The same repercussions can be caused by unauthorized modifications or adjustments, corrosion, or use of non-standard or damaged ammunition. In these cases the manufacturer shall not be responsible in any manner whatsoever for the resulting consequences.
SAFETY INSTRUCTIONS Always follow the safety instructions for your safety and the safety of others. 1. Always handle your firearm as if it were loaded. 2. Never point your firearm at anything you do not intend to shoot at. Also never point a firearm at anybody even in fun. 3. Never take anyone's word that the firearm is unloaded. 4. Always make sure that the firearm is not loaded before laying it down or handing it over to another person. 5.
21. Always keep and store your firearm and ammunition in separate secure locations out of reach and sight of children and unauthorized people. 22. Never alter any parts of your firearm; the safety and proper function of your firearm could be seriously affected. 23. Always be aware that corrosion, use of damaged ammunition, dropping the firearml on hard surfaces or other "rough treatment" can cause damage that is not necessarily obvious at first sight.
Safety instructions in case of the sights damage In regular conditions of storage, use and maintenance there is no risk to the user caused by emitted ionizing radiation, because it doesn't penetrate the metallic caps, in which the ampoules with the light sources are fixed.
The sights were type approved by the decision of the competent authority Ref. No. 25169/2005, index A1. Company representative for Tritium Light Souces: Ing. Ladislav Britaňák PISTOL DESCRIPTION AND TERMINOLOGY The names of basic pistol parts used in this Instruction Manual are presented in Fig. 1 on the inner side of the left-hand cover. Nomenclature of all CZ 75 SP-01 SHADOW parts are presented in the section List of Parts.
Versions CZ 75 SP-01 SHADOW Operation Manual Safety Safety Stop on Hammer Loaded Chamber Indicator SA/DA yes yes * CZ 75 SP-01 SHADOW LINE SA/DA yes yes * CZ 75 SHADOW LINE SA/DA yes yes * CZ 75 COMPACT SHADOW LINE SA/DA yes yes * * Loaded chamber indicator supplied on special order only Comments: SA (Single Action) The trigger mechanism operates in a single action mode of fire. The hammer is cocked manually and then after pressing the trigger the pistol is fired.
OPERATING INSTRUCTIONS Ammunition Use only factory-manufactured ammunition of appropriate caliber, which are in compliance with CIP regulations (International Proof Commission for Firearms) or SAAMI (Sporting Arms and Ammunition Manufacturers' Institute Inc. of the United States). The use of other cartridges could damage the firearm or cause injury to the shooter. Removing the Magazine Grip the pistol in your right or left hand and depress the magazine catch located by the thumb or middle finger (Fig. 2).
Unloading the Pistol ALWAYS MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION! - Remove the magazine Retract the slide and verify the last cartridge has been extracted from the chamber and ejected Let the slide snap fully forward Depress the trigger (dry fire) Engaging the Safety Push the safety up to the Safety-On position (Fig. 5) until the red warning dot is covered. The safety in this position blocks the trigger mechanism and slide, thus preventing the pulling of the trigger and operating the slide.
Sight Adjustment The pistol sights were zeroed in at the factoryt at a distance of 25 m so that the mean point of impact approximately conforms to the point of aim. The windage can be corrected by shifting the rear sight within the dovetail. Prior to the adjustment it is necessary to loosen the screw securing the rear sight against falling out. Once the rear sight has been adjusted it is necessary to tighten the screw again and secure it with the application of the Loctite 243.
Firing Pin Disassembly Push in the rear end of firing pin using a suitable tool, below the level of the firing pin stop, and press the firing pin stop approximately 2 mm down. Then cover the firing pin stop with your thumb in order not to lose the spring-loaded firing pin, and with the other hand pull the firing pin stop completely out of the slide. Be very careful at this stage of the disassembly procedure, as the firing pin is spring-loaded and could fly out, getting lost, or even causing injury.
Cleaning the Barrel and the Chamber If the pistol has not been fired or if only a few cartridges have been fired, clean the barrel and chamber with a clean patch attached to the cleaning rod. Repeat the cleaning, changing patches, until the last patch comes out clean. When the barrel is very dirty, apply a gun cleaning solution using a cleaning brush. Let the solvent act for about 10 minutes (this time may vary depending on the solvent agent being used). Then thoroughly scrub out the barrel.
LIST OF PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Frame * Slide Stop Slide Stop Spring Slide Stop Spring Pin Trigger Trigger Pin Trigger Bar Trigger Spring Pin (3x) Ejector Sear Sear Spring Sear Pin Hammer Disconnector Hammer Pin Hammer Pin Retaining Peg Main Spring Strut Main Spring Main Spring Plug Main Spring Plug Pin Magazine Guide Magazine Guide Pin Grip Panel - Left * Grip Panel - Right * Grip Panel Screw (2x) Safety - Left * Safety Detent Plunger - Left
TROUBLESHOOTING, CAUSES AND REMEDIES If your pistol is properly used and maintained, malfunctions will rarely occur. However, if such a situation does occur, please observe the following instructions. CAUTION - If a malfunction occurs, the possibility of an accidental discharge is substantially higher. For this reason, when clearing malfunctions, follow the above mentioned Safety Instructions.
TECHNICAL SPECIFICATIONS CZ 75 CZ 75 CZ 75 SP-01 COMPACT SHADOW SHADOW SHADOW LINE LINE LINE Model CZ 75 SP-01 SHADOW Caliber 9x19 9x21 9x19 9x19 9x19 Overall length [mm] 209 209 209 183 Height [mm] 150 152 146 139 Width [mm] Weight with empty magazine [g] Frame 42 34 34 35 1170 1170 1035 796 Steel Steel Steel Light Alloy Barrel length (without glide ramp) [mm] 114 114 114 92,5 Sight radius [mm] 163 163 163 143 [cartridges] 18 18 17 / 16 14 Magazine capa
