Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional discharge and could cause injury, death or damage to property. The same consequences can be caused by unauthorized modifications or adjustments, corrosion, or use of non-standard or damaged ammunition. In these cases the manufacturer shall not be responsible in any manner whatsoever for the resultant consequences.
SAFETY INSTRUCTIONS Always follow the safety instructions for your safety and the safety of others. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Always handle your pistol as if it were loaded. Never point your pistol at anything you do not intend to shoot. Never take anyone's word that a gun is unloaded. Always make sure that your pistol is not loaded before laying it down, or handing it to another person. Always keep and carry your pistol empty, except when you intend to shoot.
20. Always keep and store your pistol and ammunition in separate locked receptacles out of reach and sight of children and untrained people. Always protect the ammunition from sources of heat and open fire. Never alter any parts of your pistol as the safety and proper function of your pistol could be seriously compromised. Always be aware that corrosion, use of damaged ammunition, dropping the pistol on hard surfaces or other "coarse treatment" could cause damage you may not see.
sights closer to the shooter), the single effective radiation dose wouldn't exceed the value of 0,26 mSv.
Recommended first aid at the inspiration of the gaseous tritium The gaseous tritium state is practically inactive and causes a slight internal contamination. In case of its inspiration it is recommended to increase the intake of liquids and eventually to take some diuretic (beer with low content of alcohol) for acceleration of the body water exchange. DUTIES OF THE TRITIUM SIGHTS OWNER 1.
PISTOL DESCRIPTION AND TERMINOLOGY The names of basic pistol parts used in this Instruction Manual are presented in Fig. 1 on the inner side of the left-hand cover. Nomenclature of all parts are presented in the section List of Parts. The CZ P-10 is a semi-automatic handgun incorporating short recoil, designed for aimed shooting up to 50 m distances. The pistol utilizes the locked breech principle.
Comments: Precocked SA (Single Action) Precocked single action trigger mechanism. Before firing, the firing mechanism with striker is partially precocked. When the trigger is pulled, it is further cocked and finally released. After each firing, the trigger must be paritally released. Safety Features Trigger Guard Prevents unintentional pressing of the trigger, for example when the pistol is dropped.
down and back. We recommend that when some cartridges are already loaded in the magazine, depress them slightly with the thumb of the hand which holds the magazine. The number of cartridges can be checked through the inspection holes. Do not try to exceed the magazine capacity - doing so can cause a feeding failure. Pistol Loading ALWAYS MAKE SURE THE PISTOL IS POINTED IN A SAFE DIRECTION WHEN LOADING! Insert a loaded magazine and ensure that it has engaged the magazine catch.
MAINTENANCE INSTRUCTIONS Stripping for Cleaning - Disassembly POINT YOUR PISTOL IN A SAFE DIRECTION! 1. Remove the magazine. The pistol must not be disassembled with the magazine inserted! 2. MAKE SURE THAT THERE IS NO CARTRIDGE IN THE CHAMBER! 3. Pull the trigger and make sure that it remains in the rear position. 4. Grasp the frame with your palm, use the fingers of the same hand to grasp the rear part of the slide from the top. Use your fingers to move the slide back by no more than 5 mm (Fig. 7).
Cleaning the Barrel Bore and the Cartridge Chamber If the pistol has not been fired or if only a few cartridges have been fired, clean the barrel bore and cartridge chamber by the clean patch attached to the cleaning rod. Repeat the cleaning, changing patches, until the last patch comes out clean. When the barrel bore is very dirty, apply a gun cleaning solution using a cleaning brush. Let the solvent act for about 10 minutes (this time may vary depending on the solvent agent being used).
1. Slide * 22. Firing pin spring 2. Barrel * 23. Recoil spring 3. Firing pin 24. Extractor spring 4. Insert - front 25. Slide stop spring 5. Insert - rear 26. Trigger bar spring (2x) 6. Slide stop 27. Magazine catch spring 7. Trigger bar 28. Trigger bar disconnector spring 8. Magazine catch 29. Automatic safety spring 9. Magazine catch button 30. Disassembly plate spring 10. Trigger bar disconnector * 31. Trigger safety spring 11. Disassembly plate 32.
The parts marked * differ according to versions, or as case may be in some versions are entirely missing. The Company, reserves the right to make any changes it thinks necessary to improve its models or to meet any requirements of manufacturing or commercial nature.
TROUBLESHOOTING, CAUSES AND REMEDIES If your pistol is properly used and maintained, malfunctions will rarely occur. However, if such a situation does occur, please observe the following instructions. CAUTION - If a malfunction occurs, the possibility of unintentional discharge is substantially increased. For this reason, carefully observe the Safety Instructions already mentioned above.
TECHNICAL SPECIFICATIONS Type CZ P-10 C Caliber Overall length [mm] Overall height [mm] Width ❶ [mm] Frame 9 x 19 9 x 21 .40 S&W 187 ± 2 187 ± 2 132 ± 2 132 ± 2 32 ± 1 32 ± 1 plastic plastic Weight with empty magazine max. 765 max.
!36
!38
!40
