DECT 6.0 & 1.
DECT Base： 1. Industrial grade construction,smooth plastic finish 2. Speaker 3. Programmable Store key 4. Programmable Flash key (100ms to 1000ms timed line break) 5. Line Cord receptacle (top end of phone) 6a. HSIA(High Speed Internet Access) receptacle incoming from wall (top end of phone) 6b. PassPort○R HSIA(High Speed Internet Access) receptacle outgoing to guest laptop 7. Faceplate & Plastic Overlay display area (full-length,4-color printing possible) 8.
1 2 3 4 5 6a 24 25 26 6b 7 27 28 29 8 30 9 31 11 32a 33 10a 10b 32b 34 36 35 36 22 23 20 19 21 18 17 16a 16b 15 14 13 12 Handset： 24. Cordless Handset –Handset can be synchronized with base with a few simple steps 25. Message Waiting Indicator,blinks when message is waiting 26. ADA Compliant Handset Speaker 27. Handset Faceplate & Plastic Overlay 28. Line Selector key – Line 2 On/Off with LED indication 29. Hold/Conf.Handset key,and remote release 30.
Telephone Underside: 37. Base underside sticker information: Certification – FCC,CE,ETL,ROHS Version label Model name REN number Disposal label QC label Series number Warranty Void If Seal Broken label 38. Message Waiting selector switch TYPE LR1 LR2 39. Non-Slip rubber feet (4) 39 37 40 38 Cordless Handset Charging Station: 40. Message Waiting indication 41. Cordless Handset 42. Handset Pop-Off Cover for Battery compartment 43. Interchangeable Accent Piece,to match custom cradle color 44.
Cetis 9602MWD-N Auto Sync SERIES USERS GUIDE DECT6.0&1.
PREPARING TO USE THE 9602MWD-N SERIES 1. Prepare to install the battery into the cordless handset by Opening cover with small screwdriver.grip handset and depress Cover at hinged end.slide cover off,exposing battery compartment. 2. Slide battery plug into receptacle,matching up slot and opening On receptacle. 3. Slide battery into battery compartment. 4. Press on back end of battery to snap into place. 5. Place hinged end of cover into slot,then press down and snap into place. 6.
specific base. To accomplish this procedure, place the handset on the base in the charging position. This process occurs each time the handset is placed on the base in the charging cradle. PLACING A CALL Using the handset: 1. Pick up the handset and select either line 1 or line 2. Listen for dial tone and dial the desired number. 2. After the call is complete, press the key for the selected line again to end the call. Using the speakerphone: 1. Press key for either line 1 or line 2, or press SPKR. 2.
REDIAL The 9602MWD-N series can automatically redial the last number dialed. Off-hook, press the REDIAL key to redial the last number. USING THE HOLD KEY The HOLD key places the call on hold locally at the cordless telephone. 1. With a call active, press the red HOLD key on either the To remove a call from hold: 1. Press the line key of the call on hold. This will remove the call from hold, making the call active again. 2. The red line LED will return to steady illumination, indicating the line is active.
1. After receiving a call from first party, place them on hold as above. 2. Using the second line, place call to second party.then place them on hold as above. 3. Once those parties are on hold, activate the 3-way conference call by pressing HOLD key. User includes two callers: 1. After receiving a call from first party, place them on hold as above. 2. After receiving call from second party, place them on hold as above. 3.
RF Exposure mobile (Base) (DECT): The internal/external antennas used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. SAR: Tests for SAR are conducted using standard operating positions specified by the FCC with the UPCS handset transmitting at its highest certified power level in all tested frequency bands.
IMPORTANT SAFETY INSTRUCTIONS WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: 1. READ AND UNDERSTAND ALL INSTRUCTIONS. 2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT. 3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING. DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP CLOTH FOR CLEANING. 4.
