Installation Instructions

ManualsBrandsCetis ManualsElectronicsCordless Phone

1

2

3

4

5

6

7

Line will light up, and the base and the handset

will enter Registration

mode

.

When

the

base

and

the handset have successfully paired, the phone

will

beep

a Registration confirmation

t

one

.

SWITCH BETWEEN BASE AND

HANDSET

If the

handset

is

registered

with the

base

unit, then

the handset and base can switch the call freely

.

To

switch from the handset to the

base,

press the

Speaker key in the base unit

.

Press the

ON/OFF

key in the handset to switch from

base

to

handset

.

SWITCH BETWEEN

HANDSETS

Every base unit can

register

up to 4 additional

handsets

.

If

one

of the

handsets

is picking up, any

one of the other handsets can pick up the call by

pressing the

ON/OFF

k

e

y

.

The

ON/OFF

indicat

or

of the other handsets will flash to display the

phone is in

use

.

SPEED DIALING FROM THE HANDSET

The handset can access 6 different speed

dial

numbers programmed in the

base

.

The handset buttons are designated as

HS6–

HS11

.

Keep

in mind that the handset

simpl

y

mimics the

base

as far as programming

goes

.

So

HSM6

will automatically be the same as M6

(i

.

e

.

,

you only need to program the

base)

.

If the base unit cannot store any number, these

operations can only pick up with the

handset

.

C

ONFERENCE

The

CONF

k

e

y

allows for three-way

c

onv

er

sations

.

Depending on the situation, you may initiate a

conference call using one of these methods:

CASE A—USER INITIATES

2

C

ALLS

1

.

Place your call to the first party, then

put

them on hold by pressing the

HOLD

k

e

y

.

2

.

Using the second line (Line

2),

place

y

our

call to the second party, then put them on

hold by pressing the

HOLD

k

e

y

.

3

.

Activate

Conference

by pressing the

C

ONF

key to join the calls together

.

CASE B—USER RECEIVES A CALL

AND

PLACES A SECOND

CALL

1

.

Receive

a call from the first party, then

put

them on hold by pressing the

HOLD

k

e

y

.

2

.

Using the second line (Line

2),

place a

c

all

to the second party, then put them on

hol

d

by pressing the

HOLD

k

e

y

.

3

.

Activate

Conference

by pressing the

C

ONF

key to join the calls together

.

CASE C—USER RECEIVES A CALL AND

THEN

RECEIVES A SECOND

CALL

1

.

Receive

a call from the first party, then

put them on hold by pressing the HOLD

k

e

y

.

2

.

Using the second line (Line

2),

place a

c

all

to the second party, then put them on

hol

d

by pressing the

HOLD

k

e

y

.

3

.

Activate

Conference

by pressing the

C

ONF

key to join the calls together

.

TO TERMINATE A CONFERENCE

C

ALL

Pressing a Line key will maintain the connection

with that line while dropping the other line

.

To

terminate the call entirely, place the handset

back in the cradle to go on-hook and disconnect

both parties

.

USB CHARGING

POR

TS

The USB charging ports can charge

port

abl

e

devices (smartphone, tablet

et

c

.

)

with up

t

o

5v

2A

.

So if your guest has a device capable of

fast charging, this unit will do it

.

Simply plug a

USB (Type A)

cable into one of the provided

port

s