User's Manual

Customer Information:
1.This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
2.A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable FCC .
Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that
is also compliant. See installation instructions for details
3.If this equipment [US:2N3W410BAC9105S] causes harm to the
telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be
required. But if advance notice isn't practical, the telephone
company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC
if you believe it is necessary.
4.The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
5.If trouble is experienced with this equipment
[US:2N3W410BAC9105S], for repair or warranty information,
Service can be facilitated through our office at:
U.S. Agent Company name: Cetis, Inc.
Address: 5025 Galley Road, Colorado Springs CO, 80915
Tel: [phone]
Fax: [phone]
If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment
until the problem is resolved.
6.Please follow instructions for repairing if any (e.g. battery
replacement section); otherwise do not alternate or repair any
parts of device except specified.
7.Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public service
commission or corporation commission for information.
8.If your home has specially wired alarm equipment connected to
the telephone line, ensure the installation of this
[US: 2N3W410BAC9105S] does not disable your alarm equipment. If
you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
9.If the telephone company requests information on what
equipment is connected to their lines, inform them of:
a)The ringer equivalence number [1.0B]
b)The USOC jack required [RJ11C]
c)Facility Interface Codes (“FIC”) [02LS2]]
d)Service Order Codes (“SOC”) [9.0y]
e)The FCC Registration Number [US: 2N3W410BAC9105S]
10.The REN is used to determine the number of devices that may
be connected to a telephone line. Excessive RENs on a telephone
line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should
not exceed five (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total
RENs, contact the local telephone company. The REN for this
product is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN
without a decimal point. For this product the FCC Registration
number is [US: 2N3W410BAC9105S] indicates the REN would be 1.0.
IC Waring:
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject
to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This product meets the applicable Industry Canada technical
specifications. / Le présent matériel est conforme aux
specifications techniques applicables d’Industrie Canada.