User's Manual

ManualsBrandsCETIS ManualsElectronicsDECT Phone

ADJUSTING HANDSET RECEIVE VOLUME

The handset has eight (8) volume levels. To adjust the handset

volume, locate the volume up/down keys, located on the

handset, below the “

#” key. Pressing the “minus” (-) key will

decrease the volume level, while pressing the “plus”

(+) key

will increase it.

AUTO DIAL KEYS

The DCT1900 series has either five (5) or ten (10) programmable

guest service (auto dial) keys, depending on the model you own.

These keys can be programmed to automatically dial telephone

numbers, or to activate telephone system features.To program the

auto dial keys (programming can only be done from base unit

1. With the phone “on hook” (inactive) and the faceplate

removed, press the recessed

STORE key (see diagram).

2. Enter the desired telephone number (up to 15 digits in

length) to be stored. To enter a “pause” in the number

string, press the

REDIAL key as necessary.

3. Press the

STORE key again.

4. Press the auto dial key where the number is to be stored.

Programming is now completed for that auto dial key.

To program additional keys, repeat this process.

RECEIVING A CALL

An audible ring and flickering red LED indicate an incoming call.

o answer the call using the handset while it is not on the base:

1. Pick up the handset and press the ON key.

2. The handset will go “off-hook” answering the call.

3. To end the call, place the handset in the base unit cradle, or

press the

OFF key on the handset.

o answer the call using the handset while it is resting on the base:

1. Pick up the handset from the base. The phone will

automatically connect to the line.

2. To end the call, replace the handset in the base unit cradle,

or press the

OFF key on the handset.

o answer the call using the speakerphone:

1. Press either the LINE key or the SPKR key. The speakerphone

will go “off-hook” answering the call.

2. To end the call, press the

SPKR key to hang up.

PLACING A CALL

Using the handset:

1. Pick up the handset and press the ON key. Listen for dial

tone and dial the desired number.

2. After the call is complete, press the

OFF key to hang up.

Using the speak

erphone:

1. Press either the LINE key or the SPKR key.

2. Listen for dial tone, and dial the desired number, or press an

auto dial key to dial a preprogrammed number.

3. After the call is complete, press the

SPKR key to hang up.

REDIAL

The DCT1900 series can automatically redial the last number

dialed. On the handset, press the

REDIAL key to redial the last

number.

USING THE HOLD KEY

The HOLD key places the call on hold locally at the cordless

telephone.

o place a call on hold:

1. With a call active, press the red HOLD key on either the

handset or base unit.

2. The red line LED will flash, indicating the call is on hold.

o remove a call from hold:

1. Press the line key of the call on hold. This will remove the

call from hold, making the call active again.

2. The red line LED will return to steady illumination, indicating

the line is active.

o change phones after placing a call on hold:

1. Place the call on hold as above.

2. Pick up the call at another telephone that is on the same

line. The telephone will activate the line and remove the hold

at the original telephone.

TO MUTE THE SPEAKERPHONE

1. Press the MUTE key on the base unit. The red LED above

the

MUTE key will illuminate.The party on the other end

will not be able to hear you when the

MUTE LED is lit.

2. Press the

MUTE key again to turn off the mute feature.

The

MUTE LED will go out.

CONVERTING FROM DESK TO WALL MOUNT

The DCT1900 series can be adapted for wall mounting applica-

tions. The conversion is easiest to make when the handset and

cords are not connected.

1. Located on the handset cradle, above the speaker grill, is the

wall/desk mount clip. Remove this clip by firmly pushing it

upward towards the top of the phone.

2. Flip the clip over (top to bottom) so that the protruding edge is

towards the top of the phone and replace it in its slot.This edge

will hold the handset when the phone is mounted on the wall.

3. Turn the telephone over so the bottom is up, facing you.

Place it on a non-abrasive surface to prevent scratching.

4. Locate and remove the mounting bracket. Firmly push back

and pull up to remove two of the four retaining tabs.

5. Rotate the mounting bracket 180º degrees clockwise

, so that

the mounting eyelet on the bracket is facing in the same

direction as the other mounting eyelet located on the

bottom of the telephone.

6. Insert the top two retaining tabs of the mounting brackets

into the mounting bracket slots (located near the middle of

the telephone). Then firmly push down to insert the retaining

tabs on the opposite side of the mounting bracket.

7. Connect a 15-foot RJ-45 cord into the

LINE jack on the back

of the phone.

8. Turn the telephone over, and slide the telephone down onto

the mounting posts of the wall bracket. Ensure that both

eyelets line up with the mounting posts.

REQUIREMENTS OF PART 68 - FCC RULES

This device has been granted a registration number by the Federal

Communications Commission, under Part 68 rules and regulations for direct con-

nection to the telephone lines. In order to comply with these FCC rules, the fol-

lowing instructions must be carefully read and applicable portions followed com-

pletely:

1. Direct connection to the telephone lines may be made only through the stan-

dard modular cord furnished, to the utility installed jack. No connection may be

made to party or coin phone lines. On the bottom of the phone is a label that

contains among other information, the FCC Registration Number and the Ringer

Equivalence number (REN) for this equipment. If requested this information must

be provided to the telephone company. The

USOC Jack for this equipment is

RJ11C.

2. The telephone company, under certain circumstances, may temporarily discon-

tinue and make changes in facilities and services which may affect the operation

of the users' equipment: however, the user shall be given adequate notice in writ-

ing to allow the user to maintain uninterrupted service.

3. In certain circumstances, it may be necessary for the telephone company to

request information from you concerning the equipment which you have connect-

ed to your telephone line. Upon request of the telephone

company, provide the FCC registration number and the ringer equivalence num-

ber of the equipment which is connected to your line; this information will be

found on the device.

4. If any of your telephone equipment is not operating properly, you should imme-

diately remove it from the telephone line. It may cause harm to the telephone

network.

5. If the telephone company notes a problem, they may temporarily

discontinue service. When practical, they will notify you in advance

disconnection. If advance notice is not feasible, the telephone company must;

promptly notify you of such temporary discontinuance; afford the opportunity to

correct the condition; inform you of your rights to bring a complaint to the FCC

under their rules.

6. Repairs to the device may be made only by the manufacturer or an authorized

service agency. This applies at any time during and after

warranty. If unauthorized repair is performed, registration, connection to the tele-

phone lines and remainder of warranty period all become null and void.

7. This equipment is hearing aid compatible.

8. This telephone must be connected behind a PBX.

REQUIREMENTS OF PART 15 - FCC RULES

Statement according to FCC part 15.105: NOTE:This equipment has been tested

and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures: Reorient

or relocate the receiving antenna; Increase the separation between the

equipment and receiver; Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. Consult the dealer or

an experienced radio/TV technician for help.

Statement according to FCC part 15.21: Modifications not expressly approved

by this company could void the user’s authority to operate the equipment.

RF Exposure (Handset) (DECT): This device and its antenna must not be

co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure mobile (Base) (DECT): The internal/external antennas used for this

mobile transmitter must provide a separation distance of at least 20 cm from

all persons and must not be co-located or operating in conjunction with any

other antenna or transmitter.

INDUSTRY OF CANADA REQUIREMENTS

NOTICE: The Industry Canada label identifies certified equipment. This certifica-

tion means that the equipment meets certain telecommunications network pro-

tective operational and safety requirements as prescribed in the appropriate

Terminal Equipment Technical Requirements documents. The department does

not guarantee the equipment will operate to the users satisfaction. Before

installing this equipment, users should ensure that it is permissible to be con-

nected to the facilities of the local telecommunications company. The equip-

ment must also be installed using an acceptable method of connection. The

customer should be aware that compliance with the above conditions may not

prevent degradation of service in some situations. Repairs to certified equip-

ment should be coordinated by a representative designated by the supplier. Any

repairs or alterations made by the user to this equipment, or equipment mal-

functions, may give the telecommunications company cause to request the user

to disconnect the equipment. Users should ensure for their own protection that

the electrical ground connections of the power utility, telephone lines, and

internal metallic water pipe systems, if present, are connected together. This

precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should

contact the appropriate electric inspection authority or electrician, as appropriate.

The Ringer Equivalence Number (REN) of this device is 0.6A.

Notice: The Ringer Equivalence Number (REN) assigned to each terminal device

provides an indication of the maximum number of terminals allowed to be con-

nected to a telephone interface. The termination on an interface may consist of

any combination of devices subject only to the requirement that the sum of the

Ringer Equivalence Numbers of all the devices does not exceed 5.This tele-

phone connects to the telephone network under the connecting arrangement

code

CA11A.

Statement according to fcc part 15.214:Privacy of

communications may not be ensured when using this telephone!

1.ˇThis equipment complies with Part 68 of the FCC rules and the requirements

adopted by the ACTA. On the bottom of this equipment is a label that contains,

among other information, a product identifier in the format US:AAAEQ# # TXXXX.

If requested, this number must be provided to the telephone company.

2.ˇA plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted

by the ACTA. A compliant telephone cord and modular plug is provided with this product.

It is designed to be connected to a compatible modular jack that is also compliant.

See installation instructions for details.

3. If this equipment [US:2N3W410BDCT1905] causes harm to

the telephone network, the telephone company will notify you in

advance that temporary discontinuance of service may be

required. But if advance notice isn't practical, the telephone

company will notify the customer as soon as possible. Also, you

will be advised of your right to file a complaint with the FCC

if you believe it is necessary.

4. The telephone company may make changes in its

facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the

telephone company will provide advance notice in order for you

to make necessary modifications to maintain uninterrupted

service.

5.If trouble is experienced with this equipment [US: 2N3W410BDCT1905],

for repair or warranty information, Service can be facilitated through our office at:

U.S. Agent Company name: Cetis, Inc.

Address: 5025 Galley Road, Colorado Springs CO, 80915

Tel: 719-638-8821

6.Please follow instructions for repairing if any (e.g. battery replacement section);

otherwise do not alternate or repair any parts of device except specified.

7.Connection to party line service is subject to state

tariffs. Contact the state public utility commission, public

service commission or corporation commission for information.

8.If your home has specially wired alarm equipment connected to the telephone line,

ensure the installation of this [US: 2N3W410BDCT1905] does not disable your alarm

equipment.If you have questions about what will disable alarm equipment,

consult your telephone company or a qualified installer.

9.If the telephone company requests information on what equipment is

connected to their lines, inform them of:

a) The ringer equivalence number [ 0.6A]

b) The USOC jack required [ RJ11C]

c) Facility Interface Codes (ìFICî) [ 02LS2]

d) Service Order Codes (ì SOCî) [ 9.0y]

e) The FCC Registration Number [ US: 2N3W410BDCT1905]

10.The REN is used to determine the number of devices that may be connected to a

telephone line. Excessive RENs on a telephone line may result in the devices not ringing

in response to an incoming call. In most but not all areas, the sum of RENs should not

exceed five (5.0). To be certain of the number of devices that may be connected to a line,

as determined by the total RENs, contact the local telephone company. The REN for

this product is part of the product identifier that has the format US:AAAEQ# # TXXXX.

The digits represented by # # are the REN without a decimal point. For this product

the FCC Registration number is [ US: 2N3W410BDCT1905] indicates the REN would

be 0.6.

11.If this product is equipped with a corded or cordless handset,

it is hearing aid compatible.

Customer Information