INSTALLER / CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE Electric Fireplace Model: HEF22 HEF26 HEF33 WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY Service must be performed by a qualified service agency. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
STOP! NO NEED TO RETURN TO THE STORE Questions with the Assembly? Require Parts Information? Product Under Manufacturer’s Warranty? Call Toll-Free US: 1-800-668-5323 Canada: 1-800-668-5323 Monday to Friday 9:00 A.M. to 5:00 P.M. E.S.T.
Table of Contents PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THIS APPLIANCE Thank you and congratulations on your purchase of a CFM Corporation electric fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. Installation Instructions General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Instructions General 1. Read all instructions before using this appliance. 2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (914mm) from the front of this appliance. 3.
Fireplace Dimensions 1” (25 mm) C F J L E K J HEF26/33 A J 1/2” (13 mm) D H B L G K J HEF22 Ref.
Electrical Connection Direct (Hard) Wiring Electric Fireplace A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long three wire cord, exiting the right side of the fireplace. Plan the installation to avoid the use of an extension cord.
8. Using a slotted screwdriver, remove the 7/8" (22mm) diameter knockout from the right hand side of the cabinet above where the strain relief was located. 9. Route the electrical cable from the breaker/fuse panel through the 7/8" (22mm) diameter hole and secure to the cabinet using an approved clamp. The power wires should extend approximately 6" (152mm) into the control compartment.
Service Instructions WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. Remove Front Cover Access to heater/fan 1. Turn off power to the unit. 2. Let fireplace cool if it has been operating. 3. Remove fixed front panel, or open doors (depending on model). If the model has operable glass or mesh doors, completely remove them from the unit before proceeding.
Replacing the Light Bulbs Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt, 60 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located under the ember bed. Units with overhead lights (Fig. 9) use two (2) clear 120 Volt, 5 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located above the logs. For convenience, if one of the light bulbs burns out, it may be easier to replace all of the light bulbs at the same time. 6.
Maintenance of Motors Cleaning The motors used on the fan and the drum assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and around the air intake, located under the top shelf (Fig. 4), is recommended.
Operating Instructions 3 All of the fireplace control functions can be accessed in two (2) ways: • • 1 Using a multifunction remote control unit. Using touchpad control panel, located in the lower right-hand corner of the fireplace behind the door front or fixed front (depending on the model). The infrared remote control relies on a line of sight and must be pointed at the touchpad control panel of the fireplace to work.
Heater Control Your fireplace features a heater with a built-in thermostat and a variable temperature setting that can be controlled either by remote control or at the touchpad control panel. By depressing button 4 once, the heater will be activated and the LED visual indicator B lights up to indicate the temperature setting of the heater between the lowest (lowest light bar) and highest (highest light bar).
1 4 3 2 6 5 8 7a 9 7b 10 12 11 14 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS) 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS} 305mm [12"] 16 13 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. HEF22/26/33 Electric Fireplace Ref. 1. 2. 3. 4. 5.
HEF22/26/33 Electric Fireplace Ref. Description 6. 7a. 7b. 8. 9. 10. 11. 12. 13. 14. 15. 16.
1 YEAR WARRANTY For CFM Corporation Electric Fireplace BASIC WARRANTY: CFM Corporation (hereinafter referred to collectively as the "Company") warrants that your new electric fireplace is free from manufacturing and material defects for a period of one year from date of installation, subject to the following conditions and limitations. 1. This electric fireplace must be installed and operated at all times in accordance with the Installation and Operating instructions furnished with the product.
CFM Corporation 2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www.cfmcorp.