CF500-5B/CF500-5C CF625-B/CF625-C This ATV should not be ridden by anyone under 16 years of age. Passenger under 12 are prohibited.
Improper vehicle use can result in SEVERE INJURY or DEATH ALWAYS USE AN APPROVED HELMET AND PROTECTIVE GEAR NEVER USE WITH DRUGS OR ALCOHOL
NEVER: ●Operate without proper training or instruction . ●Operate at sppeds too fast for your skills or the conditions . ●Use ALCOHOL or DRUGS before or while operating this vehicle . ALWAYS: ●AvOid paved surfaces, which may adversely affect handling and control. ●Use proper RIDING TECHNIQUES to avoid vehicle overturns on hills and rough terrain,and in turns. ●Wear eye protection, helmet and protective clothing. READ OWNER’S MANUAL. FOLLOW ALL INSTUCTIONS AND WARNINGS.
The engine exhaust fumes from this product contains Chemicals known to cause cancer, birth defects Or other reproductive harm. A card containing important ATV safety information should be attached to the owner’s manual on the next page. If you cannot locate this card, or if it has been removed, please contact your dealer.
INTRODUCTION Congratulations on your purchase of the ATV. This manial will provide you with a good basic understanding of the features and operation of this ATV. This manual includes improtant safety information. It provides information about special techniques and skills necessary to ride your ATV. It also includes basic maintenance and inspection procedures. If you have any questions regarding the operation or maintenance of your ATV, please consult your dealer.
TABLE OF CONTENTS VEHICLE IDENTIFICATION NUMBERS................................................... 1 SAFETY.....................................................................................................3 FEATURES AND CONTROLS..................................................................37 OPERATION............................................................................................ 55 MAINTENANCE AND LUBRICATION...................................................... 79 CLEANING AND STORAGE.
VEHICLE IDENTIFICATION NUMBERS Record your ATV’s identification numbers in the spaces provided. Remove the spare key and store it in a safe place. Your key can be duplicated by using one of you existing keys. If you lose both, you will require a replacement ignition barrel and keys. 1.Frame VIN: 2.Vehicle Model Number: 3.
Operator Safety SAFETY Failure to follow the warnings contained in this manual can result in serious injury or death. An ATV is not a toy and can be hazardous to operate. This vehicle handles differently from other vehicles, such as motorcycles and cars. A collision or rollover can occur quickly, even during routine maneuvers like turning, or driving on hills or over obstacles, if you fail to take proper precautions. Read and understand your owner s manual and all warnings before operating an ATV.
Operator Safety SAFETY You should review this information on a regular basis. If you purchased a used ATV from a party other than a dealer, you can request this free safety training from any authorized dealer. This ATV is an off-road vehicle. Familiarize yourself with all laws and regulations concerning the operation of this vehicle in your area. We strongly advise you to strictly follow the recommended maintenance program outlined in your owner's manual.
SAFETY Operator Safety Serious injury or death can result if you do not follow these instructions and procedures, which are outlined in further detail within your owner’s manual. ●Read this manual and all labels carefully, and follow the operating procedures described. ●Never operate an ATV without proper instruction. Take a training course. Beginners should receive training from a certified instructor. Contact an authorized ATV dealer to find out about the training courses nearest you.
SAFETY Operator Safety ●Always keep both hands on the handlebars and both feet on the foot-rests of the ATV during operation. ●Always travel slowly and use extra caution when operating on unfamiliar terrain. Be alert to changing terrain conditions. ●Never operate on excessively rough, slippery, or loose terrain. ●Always follow proper turning procedures as described in this manual. Practice turning at low speeds before attempting to turn at faster speeds. Do not turn at excessive speeds.
SAFETY Operator Safety ●Always use proper procedures if you stall or roll backwards while climbing a hill . To avoid stalling ,maintain a steady speed when climbing a hill. If you stall or roll backwards, follow the special procedure for braking described in this manual. Always dismount on the uphill side, or to either side if the ATV is pointed straight uphill. Turn the ATV around and remount following the procedure described in this manual. ●Always check for obstacles before operating in a new area.
Operator Safety SAFETY ●Always check for obstacles or people behind the ATV before operating in reverse. When it s safe to proceed in reverse, move slowly and avoid turning at sharp angles. ●Always use the size and type of tires specified for your ATV, and always maintain proper tire pressure. ●Never modify an ATV through improper installation or use of accessories. ●Never exceed the stated load capacity for your ATV. Cargo must be properly distributed and securely attached.
SAFETY Operator Safety Equipment Modifications We are concerned with the safety of our customers and for the general public. Therefore , we strongly recommend that consumers do not install on an ATV any equipment that may increase the speed or power of the vehicle, or make any other modifications to the vehicle for these purposes. Any modifications to the original equipment of the vehicle create a substantial safety hazard and increase the risk of body injury.
SAFETY Operator Safety POTENTIAL HAZARD Operating this ATV without proper instruction. WAHT CAN HAPPEN The risk of an accident is greatlly increased if the operator does not know how to operate the ATV properly in different situations and on different types of terrain. HOW TO AVOID THE HAZARD Beginning and inexperienced operators should complete the certified training course offered by dealer.
SAFETY Operator Safety WHAT CAN HAPPEN Severe injury and/or death could occur if a child under the minimum age recommendation operates and ATV, Even though a child may be within the recommendation age group for operating some ATV, he/she may not have the skills, abilities, or judgment needed to operate an ATV safely and could be susceptible to accident or injury. HOW TO AVOID THE HAZARD No one under the age of 16 should operate this ATV.
SAFETY Operator Safety POTENTIAL HAZARD Carring a passenger on the rear rack. WHAT CAN HAPPEN A passager riding on the rear rack could be ejected from vehicle unexpectedly or may contact moving components, both of which can result in severe injury or death. HOW TO AVOID THE HAZARD Never allow passengers to ride on the rear rack.
Operator Satety SAFETY POTENTIAL HAZARD Operating this ATV without wearing an approved helmet, eye protection and protective WHAT CAN HAPPEN Operating an ATV without an approved helmet increases the risk of a severe head injury or death in the event of an accident. Operating without eye protection could result in an accident and could increase the chance of a severe injury in the event of an accident. HOW TO AVOID THE HAZARD Always wear an approved helmet that fits properly.
SAFETY Operator Satety POTENTIAL HAZARD Operating the ATV after consuming alcohol or drugs. WHAT CAN HAPPEN Consumption of alcohol and/or drugs could seriously affect operator judgment. Reaction time may be slower and operator balance and perception could be affected. Consuming alcohol and/or drugs before or while operating an ATV could result in an accident causing severe injury or death. HOW TO AVOID THE HAZARD Never consume alcohol or drugs before or while operating an ATV.
Operator Satety SAFETY POTENTIAL HAZARD Operating the ATV at excessive speeds. WHAT CAN HAPPEN Excessive speed increases the operator’s chance of losing control of the ATV, which can result in an accident . HOW TO AVOID THE HAZARD Always operate the ATV at a speed that’s proper for the terrain, visibility and operating conditions, and your experience. POTENTIAL HAZARD Attempting wheelies, jumps and other stunts.
SAFETY DRIVER SAFETY POTENTIAL HAZARD Operating thie ATV/QUAD without proper inspection,ATV/QUAD improper maintain. What will happen. Improper maintain will increase accident occurrence and equipment damage probability. How to avoid such dangerous. Alwaysdo inspection on ATV before operate it to make sure that the vehicle in safe operating state, Always strictly follow the inspection and maintainance procedure described in your owner’s manual.
SAFETY DRIVER SAFETY How to avoid the hazard. Always use both hands hold the levers and keep the feet on foot boards when driving the ATV. Potential hazard Careless driving on unfamiliar terrain. What will happened Unfamiliar terrain(hidden rocks,bumps,or holes that may cause lose balance even rollover.
SAFETY DRIVER SAFETY Potential hazard.Careless driving on over rugged,slippery,soft terrain. What will happened. Driving on over rugged,slippery,soft terrain may cause lose traction or lose control of the vehicle,so cause accident or rollover. How to avoid the hazard. Please also drive carefully when on the bad terrain with technique.
SAFETY Driver Safety WHAT CAN HAPPEN Improper turns could cause loss of control and lead to a collision or overturn. HOW TO AVOID THE HAZARD Always follow the turning methods described in the owner’s manual. Practise turning at a low speed before you trying to turning at a high speed. Never try to sharp turn in high speed. POTENTIAL HAZARD Diving on too steep area. WHAT CAN HAPPEN The vehicle may overturn. HOW TO AVOID THE HAZARD Never driving ATV on too steep terrain or on area beyond ATV ability.
SAFETY DRIVER SAFETY POTENTIAL HAZARD Improper climbing method. WHAT CAN HAPPEN Improper climbing may cause loss of control or overturn. HOW TO AVOID THE HAZARD Always follow the proper climbing method instruted in the owner’s manual. Observe the terrain condition before climbing. Never driving ATV on area grade large than 25°. Never climbing highland too slip or soft,transfer your weight forward when climbing. Never open the throttle suddenly when climbing,or else the ATV will overturn backwards.
SAFETY Driver safety POTENTIAL HAZARD Improper descent. WHAT CAN HAPPEN Improper descent may cause loss of control or overturn. HOW TO AVOID THE HAZARD Always follow the descent method instructed in the owner’s manul. NOTE： You required special technique on down hill braking,please refers to Page69. Observe the terrain carefully before down hill,also transfer your weight backwards. Never down hill in with high speed.
SAFETY Driver Safety POTENTIAL HAZARD Improper operation when crossing or turning in highland. HWAT CAN HAPPEN Improper operation when crossing or turning in highland may cause loss of control or overturn. HOW TO AVOID THE HAZARD Only if you mastered turning skill on plat land then you can try to turn on all terrain. Please refers to Page68.
SAFETY Driver safety POTENTIAL HAZARD Flameout,backwards,improper down hill operation. WHAT CAN HAPPEN The vehicle body may may roll over. HOW TO AVOID THE HAZARD Keep stable speed when climbing; Keep your weight in uphill; Brake with front brake(or brake lever),when the vehicle complete stop, apply the rear brake, then put into park gear.
SAFETY DRIVER SAFETY Do not apply rear brake when move backwards,apply front brake slowly(or brake lever). Apply rear brake when the vehicle complete stop,then putinto park gear. Turning and downhill according to the owner's instruction,refers to Page65.Page69. POTENTIAL HAZARD Improper operation when span obstacles. WHAT CAN HAPPEN Driving across big obstacles may cause loss of control or overturn. HOW TO AVOID THE HAZARD Before driving on unfamiliar terrain, observe the road condition carefully.
SAFETY Driver Safety POTENCIAL HAZARD The vehicle side-slip or slide WHAT CAN HAPPEN Vehicle side-slip or slide may cause vehicle loss control,if the tyre once again obtain pull, the vehicle may overturn. HOW TO AVOID THE HAZARD When driving slowly on slippy surface such as ice,you must pay much attention to the vehicle side-slip or slide. POTENTIAL HAZARD ATV overload or transport/improper pull.
Driver Safety SAFETY HOW TO AVOID THE HAZARD Cannot exceed the ATV nominal load Placing and pack the goods properly;speed-down according to the owner's instruction when carry goods or pulling, keep longer brake distance,refers to owner's manual Page 61. POTENTIAL HAZARD Driving across deepwater or rapids. WHAT CAN HAPPEN The tyres may float and cause loss control of the vehicle,thus lead to accident.
Driver Safety SAFETY Wet brake may degrade brake performance,inspect brake condition when out of water, brake lightly for several times to dry the brake pads. POTENTIAL HAZARD Improper vehicle reverse. WHAT CAN HAPPEN ATV may make collide with obstacle or person and cause serious accident. HOW TO AVOID THE HAZARD Check if there is any person when during reversing. Reverse slowly after look over. POTENTIAL HAZARD Using off-gauge tyre,under inflation tyre,uneven pressure between tyres on ATV.
SAFETY Driver Safety HOW TO AVOID THE HAZARD Always use the specified types and size of ATV tyres described on the owner's manual. Always maintain right tyre pressure. POTENCIAL HAZARD Drive improper remodel ATV WHAT CAN HAPPEN Install unfit parts or do improper modification on the vehicle may change vehicle operating performance and lead to accident.
SAFETY Operator Safety POTENTIAL HAZARD Operating on frozen bodies of water. WHAT CAN HAPPEN Severe injury or death can result if the ATV/Quadricycle and /or the operator fall through the ice. HOW TO AVOID THE HAZARD Leaving the keys in the ignition can lead to unauthorized use of the vehicle resulting in serious injury or death. Always remove the ignition key when the vehicle is not in use.
SAFETY Operator Safety - 29 -
SAFETY - 30 -
SAFETY - 31 -
SAFETY - 32 -
SAFETY GEAR - 33 -
SAFETY Safe riding gear Always wear clothing suited to the type of riding.ATV/Quadricycle riding requires special protective clothing for comfort and to reduce the chance of injury. 1.Helmet Your helmet is the most important piece of protective gear for safe riding.An approved helmet can prevent a severe head injury. 2.Eye protection Do not depend on sunglasses for proper eye protection for your eyes. They should be kept clean and be shatterproof design. 3.
FEATURES AND CONTROLS Electrical Switches Activate override switch while throttle is open can cause loss of control,resulting in severe injury or death.Never press override switch while throttle is open. 1 1.Override Switch Top speed is limited when in 4WD-LOCK condition.If more engine power required when riding,push and hold this switch to override the 4WD-LOCK speed limit. (Refer to page45 for detailed explanation about the override switch) 2 Speed limit restores when the switch released.
Electrical Switches FEATURES AND CONTROLS When the switch is at“3 ”position,all lghts are off. When the switch is at“4”position,the front/rear position light and instrument light are on. 3.Turning light switch Press the switch to“ ” ,Left turning indicator and left turning light are on. Press the switch to“ ”,Right turning indicator and right turning light are on. 4.Horn Switch Button Press the button,the horn will sound. 5.Start switch Press the button,start motor runs. 6.
FEATURES AND CONTROLS 1 Brake Front brake lever Front brake lever 1 is located on the right handlebar.Pull it toward the handlebar to apply the front brake. Combined brake Brake pedal 2 is located on the right of the engine， combined brake lever 3 is located on the left handlebar. Step on the pedal or pull the lever toward the handlebar to apply the rear linkage brake.
FEATURES AND CONTROLS Brake Always test brake lever and master cylinder fluid level before riding.When squeezed,the lever should feel firm.Any sponginess would indicate a possible fluid lrak or low master cylinder fluid level,which must be corrected before riding.Contact your dealer for proper diagnosis and repairs. Brake Fluid Check the brake fluid level in front brake oil cup and linked brake main pump oil cup before using the ATV/Quadricycle.The front brake oil cup is located in the right handlebar.
FEASTURES AND CONTROLS Brake An over-full master cylinder may cause brake drag or brake lock-up,which could result in serious injury or death.Maintain brake fluid at the recommended level.Do not overfill. NOTE：When checking the fluid level,the ATV/Quadricycle must be on level ground with the handlebars straight.If the fluid level is low,add DOT3/DOT4 brake fluid.
FEATURES AND CONTROLS Brake Parking Brake When parking,stop the engine and shift the gear selector Lever① into the park position. Operation the ATV/Quadricycle while the parking brake is engaged could result in an accident and serious injury or death. Always check to be sure the parking brake is disengaged. Before operatiog. Important Safeguards ● The parking brake may relax if left for a long period of time.Always block the wheels to prevent rolling.
FEATURES AND CONTROLS Efisystem ● Disassemblyof the EFI system is forbidden; ● Ignition switch must be off while connector is on or off on order not to damage electric elements; ● Do not diamantle battery while engine is working; ● Engine starting is not allowed in case of no fuel or fuel below warning line to protect oil pump damaged; ● Idling adjustment is handled by EFI system only and does not need manul adjustment; Fuel tank Fuel tank filter cap ① is loacated below the handlebar.
Fuel safety FEATURES AND CONTROLS Fuel is highly flammable and explosive under certain circumstances. ●Always handling fuel in a extremely attentive and careful state on mind; ●Always refuel while engine stops in a well ventilated situation; ●Never fill gass while plastic fuel tank is on the rack. Static electricity between rack and tank could cause a spark; ●Refuel after engine stops in a well ventilated situation and do not smoke or create a spark in gas station or storeage place.
FEATURES AND CONTROLS Gearshift Gearshift unit is on left side of the vehicle. L：Low gear H：High gear N：Neutral R：Reverse gear In order to shfit into reverse gear, step onto brake pedal first. It the same to shift out of reverse gear; CAUTION： When engine speed is above idle speed or change gears while vehicle is moving, engine could be damaged.Stop vehicle while changing gears and engine in idel speed.
FEATURES AND CONTROLS Belt life-span Changing into low gear while pulling heavy stuff to prolong belt life-span; If it is necesary to pull vehciles, change into neutral gear for better flexibility to protect belt from being damaged; Recoil starter If power is not enough to start the engine, please use ① recoil starter.Vehicle is still operable while it is under overraul. ① is on left side of vehicle. Engie is equipped with pressure reliefer.
FEATURES AND CONTROLS Recoil starter CAUTION Recoil starter could be damaged if rope is pulled too long, possibly lead to starter fails; If the rope is not in correct position,water might penetrate and damage components; Make sure the handle is within housing, expecially while riding in wet situation: All-Wheel Driven（AWD）System 2 1 Lock switch based on 4 wheel drive or differential choice; The vehicle is equipped with“2WD”/“4WD”① and differential“LOCK”/“4WD”②; Change into proper driven gear based on circu
FEATURES AND CONTROLS All-wheel drive（AWD）System Choose 4WD based on actual need. “2WD/4WD”switch Stop the vehicle to change 2WD to 4WD if necessary. And then change switch to “4WD”. When in 4WD, on dashboard will show “ ” Stop the vehicle and make sure the handle bar ① is in position in 4WD position. 1 1 2 2 4WD differentuial lock switch① In order to lock 4WD,make sure switch is in 4WD based on actual need, stop ATVand pull ② to “ ”posi t ion and then change switch to “lock”position.
FEATURES AND CONTROLS All-wheel drive（AWD）System NOTE： ●When switch is in “lock”position, dashboard light shows continuously; ●In case light shines,4WD is not locked and ATV should be driven in low speed.
FEATURES AND CONTROLS All-wheel drove（AWD) System CAUTION Check throttle tie-rod before starting the engine. In case of problems, check and solve the reasons before riding the ATV. Contat local dealer if necessary. Speed limitator Spped limitator can provent throttle full open even if throttle is in highest position:Turn bolt ② gain highest power to decrease max speed of the ATV. CAUTION Never adjust the bolt longer than 12mm, make sure throttle clearance is between 3-5mm.
FEATURES AND CONTROLS Main switch Functions: ON：Start the engine and key cannot be taken out in this position; OFF: Close all electric circuits and key can be taken out in this position.
FEATURES AND CONTROLS Indicator light and caution light 4WD indicator lights① Switch“(2WD)/(4WD)”onto position “(4WD)", the indicator light shows; Switch“LOCK-”-“(4WD)”onto“LOCK-(4WD)”,the indicator light shows.
FEATURES AND CONTROLS Indicators and caution lights Parking gear indicator“R”⑥ When gear in position “R”, the indicator shows; Parking indicator“P”⑦ When gear is in“P”position, the indicator shows; Turning righg indicator⑧ Press turning The indicator shows; Assistor light indicator⑨ Switch on the assistor, the indicator shows; High beam indicator⑩ Swith on front light“ ”, the indicator shows; Position ”, the indicator shows; Press position l i ght“ Trouble 12 in case of trouble, see Page 134.
FEATURES AND CONTROLS Dashboard Coolant temperature indicator When the temperature indicator is in the white area of side C, it means that the temperture is normal. The red area of the side H indicates temperature is high.If so please stop the engineuntil temperature is down. In case temperature frequently goes high, check coolant capacity or contact the dealer. CAUTION： ●Engine may overheat if ATV is overlaoaded. Reduce Weight to specification in case of this.
FEATURES AND CONTROLS Puller electric outlet, position,power Output :12V 1 This spare electric loutlet provides power for rearlights, rear turning lights etc of the the puller.
Driving 55. 6.Less load ,more better。 7.check oil and filter by Each 25 hours or each month during break-in period.
Driving Pre-Ride Inspection If a proper inspection is not done before each use ,severe injury or death could result.always , inspect the vehicle before each use to ensure it s in proper operating co n d io n .
Driving Pre-Ride Inspection brake light/tail lamp Inspect,ensure tightness Ensure proper level Ensure proper level Inspect for leaking Ensure proper operation Ensure proper operation Inspect,clean Drain deposits whenever visible Check operation Check operation Riding accessories Wear helmet,goggles,protective clothing Frame nuts,bolts,fasteners Fuel and oil Coolant level Coolant hoses Throttle Indicator lights/swithches Air filter Air box sediment tube Headlamp - 56 - 86 91 47 35，50 97 113 115 34
Driving - 57 -
Driving Starting engine 4.release throttle completely and puse the srart switch. NOTE： ● If the engine fails to start, release the start switch,then push the start switch again.pause a few seconds before the next attempt.Each cranking should be as short as possible to preserve battery energy.Do not crank the engine more than 10 seconds on each attempt. ● If the battery is discharged,pull the recoil starter to start the engine.
Driving - 59 -
Driving - 60 -
Driving When you shift into reverse,make sure there are no obstacles or people behind you. When it is safe to proceed,go slowly. Hauling Cargo Carrying a load on only the front rack or the rear rack may cause an imbalanced condition and increases the possibility of vehicle overturn. ● do not exceed the stated load capacity. ●speed-down and keeping longer distance for breaking. ●speed-down and less loading when driving in rough treeain or hill. ●load distribution.
Driving - 62 -
Driving - 63 -
Driving Driving Procedures - 64 -
Driving - 65 -
Driving - 66 -
OPERATION - 67 -
OPERATION Driving safely Driving Uphill Braking and handling are greatly affected when operating in hilly terrain. Improper procedure could cause loss of control or overturn and result in serious injury or death. Avoid climbing steep hills (25°maximum) Use extr eme caution when operating on hills,and followproper operating procedures outlined in the owner’s manual. Sidehilling Improperly crossing hills or turing on hills can result in loss of control or vehicle overturn,resulting in severe injure or death.
OPERATION - 69 -
OPERATION - 70 -
OPERATION 1. 2.
OPERATION 100 - 72 -
OPERATION - 73 -
OPERATION - 74 -
OPERATION - 75 -
OPERATION - 76 -
OPERATION - 77 -
MAINTENANCE AND LUBRICATION - 78 -
MAINTENANCE AND LUBRICATION - 79 -
MAINTENANCE AND LUBRICATION Periodic Maintenance Chart Perform all services at whichever maintenance interval is reached first.
MAINTENANCE AND LUBRICATION Periodic Maintenance Chart Coolant Daily Check level daily,change coolant Every 2 years Headlamp/tail lamp Daily Check operation Air filter,main element Weekly Recoil housing Weekly Inspect, replace as needed Drain water as needed, check often if operating in wet condition.
MAINTENANCE AND LUBRICATION Periodic Maintenance Chart ■ ■ - 82 - Shift lever 28H 1M 500 Inspect;lubricate;adjust， Steering 50H 3M 500 Lubricate Front suspension 50H 6M 500 Lubricate Rear suspension 50H 6M 500 Lubricate Throttle Cable/ETC Switch 50H 6M 500 Inspect;adjust;lubricate; Replace, if necessary Drive belt 50H 6M 500 Inspect;adjust.
MAINTENANCE AND LUBRICATION Periodic Maintenance Chart ■ ■ Fuel tank vent hose 100H 12M 1000 Inspect routing condition Valve clearance 100H 12M 1000 Inspect;adjust Fuel system 100H 12M 1000 Radiator 100H 12M 1000 Inspect;clean extemal surface Cooling hoses 100H 12M 1000 Inspect for leaks Engine mounts 100H 12M 1000 Inspect Exhaust muffler/pipe 100H 12M 1000 Inspect Spark plug 100H 12M 1000 Inspect;replace as needed ， Wiring 100H 12M 1000 Inspect for wear,routing
MAINTENANCE AND LUBRICATION Periodic Maintenance Chart ■ Clutches (drive and driven) 100H 12M 1000 Inspect;clean;replace worm parts ■ Wheel bearings 100H 12M 1000 Inspect;replace as needed ■ Brake fluid 200H 24M 1000 Change every two years Spark arrestor 300H 36M 1000 Clean out ■ ■ Idle speed Inspect parts Toe adjustment Inspect periodically;adjust when parts are replaced.
MAINTENANCE AND LUBRICATION Lubrication Recommendations Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on page 79.Items not listed in the chart should be lubricated at the General Lubrication interval.
MAINTENANCE AND LUBRICATION Lubrication Recommendations Engine oil Always check and change the engine oil at the intervals outlined in the Periodic Maintenance Chart beginning on Page 80.Always change oil filter whenever chnaging oil. Engine Oil Check 1.Pull outward on the areas shown ① 2.Position the ATV on a level surface 3.Start engine and left it idle for 20-30 seconds;stop the engine. 4.Wait a few minutes until the oil settles 5.Remove engine oil dipstick ① 6.
MAINTENANCE AND LUBRICATION Engine Oil Check 7.If the engine oil is at or below the lower limit remark, add sufficient oil of the recommended type to raise it to the correct level. 8.Insert the dipstick into the oil filler hole,and then tighten the oil filler cap. 9.Install the panel. To change the engine oil 1.Start the engine,warm it up for several minutes,and then turn it off 2.Place an oil pan under the engine to collect the used oil, and then remove the engine oil filler cap. 3.
MAINTENANCE AND LUBRICATION To change the engine oil 5.Apply a light coat of engine oil to the O-ring of the new oil filter cartridge. NOTE：Make sure the O-ring is seated properly. 6.Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. NOTE：Oil filter cartridge tightening torque:：17N.m 7.Install the engine oil drain bolt, and then tighten it to the specified torque. NOTE：Engine oil drain bolt tightening torque：30N.m 8.
MAINTENANCE AND LUBRICATION To change engine oil Rear gear case oil The rear gear case must be checked for oil leakage before each ride. If any leakage is found,have your dealer check and repair the ATV Rear gear case oil replacement 1.Place the machine on a level place. 2.Place a container under the rear gear case to collect the used oil. 3.Remove the oil filler bolt and the drain bolt to drain the oil. 4.Install the drain bolt and tighten it to the specified torque.
MAINTENANCE AND LUBRICATION Rear gear case oil replacement 6.Install the filler bolt and tighten to the specified torque. NOTE：Filler bolt（rear gear case）tightening torque：23N.m 7.Check for oil leakage.If oil leakage is found,check for the cause. NOTE：Be sure no foreign material enters the rear gear case Front gear case oil measurement 1.Place the machine on a level place. 2.Remove the oil filler bolt and check the oil level.It should be up to the brim of the hole.
MAINTENANCE AND LUBRICATION Front gear case oil replacement 4.Install the drain bolt and tighten it to the specified torque. NOTE：Drain bolt tightening torque:10N.m 5.Fill the front gear case with oil NOTE：Periodic oil change oil quantity:0.28L Total amount oil quantity:0.33L 6.Inspect the filler bolt and tighten it to the specified torque. 7.Check for oil leakage.If oil leakage is found,check for the cause. NOTE：Be sure no foreign material enters the front gear case. Cooling system 1.
MAINTENANCE AND LUBRICATION Cooling System 3.If the coolant is at or below the lower limit mark, remove the reservoir cap,add coolant to the uuper limit mark,install the reservoir cap,and then install the panel. NOTE：Coolant reservoir capacity(up to the upper limit mark):0.3L CAUTION： Hard water or salt water is harmful to the engine.
MAINTENANCE AND LUBRICATION Changing the coolant 5.Disconnect the hose on the on the coolant reservoir, and then drain the coolant out.。 6.After draining out the coolant, flush the cooling system with clean water. 7.Replace the coolant drain bolt washer if damaged, and tighten it as per stipulated torque. NOTE：Torque：10N.m 8.Install the coolant reservoir hose. 9.Fill the radiator with recommended coolant till full.
MAINTENANCE AND LUBRICATION Changing the coolant Coolant reservoir capacity (Up to the Upper limit mark) Capacity：0.3L。 CAUTION Hard water or salt weater is harmful to engine. Make sure to use soft water once you can’t get coolant. 10.Instasll the radiator cap. 11.Start the engine, and keep it runing in idle speed for several minutes;Shut the engine, and then check the coolant level;If the level is low, fill the coolant till the top of radiator. 12.Fill the coolant into reservoir till up to Upper limit.
MAINTENANCE AND LUBRICATION Axle boots Check the protective boot for hole or tears. If there is any damage,have your dealer replace it. Check the spark plug Removal 1.Remove the panel. 2.Remove the spark plug cap. 3.Remove spark plug with wrench in the tool kit as per instruction.
Inspection MAINTENANCE AND LUBRICATION Spark plug is an important engine part，and is easy to inspect. The condition of spark plug can indicate the engine condition. For a normal ATV,The ideal color on the white white insulator around the center electrode is medium-to-light brown color. Do not attempt to diagnose the problem by yourself, but have your dealer inspect it.Periodically remove and inspect the spark plug, because the heat and deposit will cause the spark plug damage and erode corrosion slowly.
MAINTENANCE AND LUBRICATION Installation 3.Install the spark plug and tighten it as per stipulated torque. NOTE：Spark plug torque：17.5N.m。 If you have no torque wrench when you install the spark plug, 1/4 to 1/2 turn more after tightening the spark plug by hand will be appropriate.Tighten the spark plug to stipulated torque as soon as possible. 4.Install spark plug cap. 5.Installthe panel. Cleaning Air filter element NOTE：There is a check soft hose in air filter box.
MAINTENANCE AND LUBRICATION Cleaning Air filter element 1.Remove the seat; 2.Open the bracket and remove air filter box cover; 3.Remove air filter; 4.Disassemble air filter from bracket;； 5.CLean the air filter quitely with solvent;； 6.Squeeze the excessive solventout out of the air filter, and then dry it. CAUTION： Do not damage the air filter when squeezing the solvent; 7.Check the air filter and replace it if damaged; 8.Apply special oil or other good quality foam air filter oil on the air filter.
MAINTENANCE AND LUBRICATION Cleaning air filter element 12.Install the seat; NOTE： Clean the air filter element every 20-50 hours;More frequent cleaning and lubrication should be done when operating the vehicle in dust area.After each use, inspect the intake hole on the air filter box cover for obstruction.Inspect the sealing between air filter rubber connector and air hose joint of the carburetor;Tighten all fitting securely to avoid unfiltered air entering the engine.
MAINTENANCE AND LUBRICATION Cleaning spark arrester 4.Insert the exhaust pipe into the muffler aligning the bolt hole; 5.Install and tighten the bolts. Cool down the muffler when cleaning the spark arrester.； Not allowed to operate immediately shut the engine. V-belt cooling duct inspect soft hose If there is deposit or water inside, remove the soft hose and clean it.
MAINTENANCE AND LUBRICATION V-belt case drain bolt When riding the vehicle in water, which reaches height of V-belt case, remove the bolt to drain the water from V-belt cae. NOTE：If draining water from V-belt after removing the drain bot,have you dealer check the ATV，because water may affect other engine parts.
MAINTENANCE AND LUBRICATION Adjusting throttle lever 1.Loosend half nut; 2.Turn the adjusting nut to keep 3-5mm throttle lever free play. 3.Tighten haf nut.
MAINTENANCE AND LUBRICATION Inspecting from brake caliper Check the brake disc for damage and wear. If thickness of brake disc is less than 3.0mm, have your dealer replace the whole brake pads. NOTE：Need to removethe wheels to check the brake pads.
MAINTENANCE AND LUBRICATION Checking rear disc Check the brake disc for damage and wear. If the brake disc thickness is less than 6.5mm, have your dealer replace the brake pads. Check the brake fluid level Insufficient brake fluid may allow the air enter the braking system.and cause the brake in disorder； Before riding, check the brake fluid level above the Lower Limit mark,and add brake fluid if necessary.
MAINTENANCE AND LUBRICATION Checking brake fluid level Observe these precautions: 1.When checking brake fluid level,turn the grip to make sure top level of master cylinder resorvior. 2.Only use appointed good quality brake fluid, otherwise, rubber seals will be deteriorated, causing leakage and poor brake performance. NOTE：Recommended brake fluid：DOT3 or DOT4。 3.Refill with same type brake fluid till full. Mixed brake fluid may cause hramful chemical reaction and lead to poor brake performance. 4.
MAINTENANCE AND LUBRICATION Process to Replace Brake Fluid Replacement shall be done only by trained service man; Dealers need to replace Brake Fluid when making Maintenance ,or when parts are damaged, or when Break Fuid leaks ●Replace Oil Seal once every two years. ●Replace Braking Hose once every four years. ●Free play at end of Braking Lever shall be zero mm;otherwise please ask your dealer to check the Braking System. Make Sure after Maintenance that ●Braking successfully with enough clearance.
MAINTENANCE AND LUBRICATION Adjustment of Rear Brake Lever and Footpedal Adjustment of Rear Brake Lever Clearance Rear Brake Lever clearance is 0.5-2mm 1.Unscrew Locking Screw①。 2.Turn Bolt 2 to increase clearance; Turn Bolt 2 with direction 3.Tighten Screw①。 Please send to dealer if adjustment cannot be done.
MAINTENANCE AND LUBRICATION Rear Brake Pedal Adjustment Top of Rear Brake Pedal shall be 72mm higher from the end;otherwise please ask your dealer to adjust. After servicing,make sure that ●Make sure the brakes operate smoothly and that the free play is correct. ●Make sure the brakes do not drag. All air must be bled from the brake system. Replacement of brake components requires professional knowledge. These procedures should be performed by your dealer.
MAINTENANCE AND LUBRICATION Rear Brake Pedal Height Adjustment Turn adjustment nt while pushing rear brake light switch；Brake light is on in advance while turning with direction ① Brake light on is delayed while turning with direction ② Inspection and lubrication of wiring and cables. It is necessary to inspect oftenly the wirings and cables;replace if there is any damage.Lubricate the moving point of cables; If cables are not moving well,contact your dealer for replacement.
MAINTENANCE AND LUBRICATION Wheel Removal 1. Loosen the wheel nuts. 2. Elevate the ATV and place a suitable stand under the frame. 3. Remove the nuts from the wheel. 4. Remove the wheel. Wheel Installation 1. Install the wheel and the nuts. NOTE：● Tapered nuts are used for both the front and rear wheels. Install the nut with its tapered side towards the wheel. mark on the tire must point toward the rotating direction of the wheel.
MAINTENANCE AND LUBRICATION Wheel Installation 2. Lower the ATV so that the wheel is on the ground. 3. Tighten the wheel nuts to the specified torque. NOTE：Wheel Nut Torque：Front 55N.m；Rear：55N.m This machine is equipped with a sealed-type battery. Therefore it is not necessary to check the electrolyte or add distilled water in the battery. If the battery seems to have discharged, consult your dealer. NOTE： Do not try to remove the sealing caps of the battery cells. You may damage the battery.
MAINTENANCE AND LUBRICATION Battery Maintenance When the machine is not used for a month or longer, remove the battery and store it in a cool, dark place. Completely recharge the battery before reinstallation. CAUTION： A special battery charger (constant voltage/ampere or constant voltage) is required for recharging a sealed- type battery. Using a conventional battery charger may shorten the battery life. 2. Always make sure the connections are correct when putting the battery back in the machine.
MAINTENANCE AND LUBRICATION Replacement of Fuse CAUTION To prevent accidental short-circuiting, turn off the main switch when checking or replacing a fuse. Replacement of Headlight Bulb + W5W 1.Pull out Rubber Cover at the back of headlight. 2.Remove Rear Holder of headlight. 3.Remove headlight from headlight rear holder. + + E40013486 HS1 + Wait till bulb is cold before any touch or removal of bulb.
MAINTENANCE AND LUBRICATION Replacement of headlight Bulb 4. Insert a new headlight bulb into the headlight bulb holder, and then lock it by spring.。 5. Install the bulb holder by turning it clock-wise 6. Install the rubber cover at the rear of the headlight 7. Install the headlight cover with the bolts. Headlight Beam Adjustment CAUTION It is advisable to have your dealer make this adjustment. Turn the adjusting screwscan raise or lower the beam.
MAINTENANCE AND LUBRICATION Tail/Brake Light Bulb Replacement If the tail/brake light bulb burns out, replace it as follows: 1. Remove the screws , and then pull tail/brake light cover ② out. 2. Remove the tail/brake light bulb by pushing it in and turning it counter-clockwise. 3 . Insert a new tail/brake light bulb, push it in, and the turning it clockwise. 4. Install the tail/brake light cover with the screws.
MAINTENANCE AND LUBRICATION Front and Rear Suspenson Adjustment The spring preload can be adjusted to suit the rider s weight and riding conditions. NOTE：When adjusting the rear shock absorbers, the rear wheels need to be removed. Adjust the spring preload as follows.。 To increase the spring preload, turn the adjusting ring in direction(a)(b) To decrease the spring preload, turn the ad-justing ring indirection(b) NOTE：A special wrench can be obtained at a dealer to make this adjustment .
MAINTENANCE AND LUBRICATION Vehicle Immersion CAUTION If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine. If it s impossible to take your ATV to a dealer before starting it, follow the steps outlined below. 1. Move the ATV to dry land or at the very least, to water below the footrests. 2. Remove the spark plug. 3. Check the air box and drain if there is water. 4.
Cleaning and Storage Cleaning of ATV Keeping your ATV clean will not only improve its appearance but it can also extend the life of various components. With a few precautions, your ATV can be cleaned much like an automobile. Washing the ATV The best and safest way to clean your ATV is with a garden hose and a pail of mild soap and water. Use a professional type washing mitten, cleaning the upper body first and the lower parts last. Rinse with water frequently and dry with a chamois to prevent water spots.
Cleaning and Storage CAUTION Starting the engine during the storage period will disturb the protective film created by fogging and damage could occur.Never start the engine during the storage period. Clean the Exterior Make necessary repairs and then clean the ATV/Quadricycle thoroughly with mild soap and warm water to remove all dirt and grime.Don't use harsh detergents or high pressure washers. Some detergents deteriorate rubber parts.Use dish soap type cleaners only.
Cleaning and Storage Air Filter/Air Box Inspect and clean or replace the pre-cleaner and air filter.Clean the air box and drain the sediment tube. Breather Filter Inspect and clean or replace the breather filter. Fluid Levels Inspect the following fluid levels and change if necessary:front gear case; transmission; brake fluid(change every 2 years or as required if fluid looks dark or contaminated). Lubricate the Engine Remove the spark plug and add 2-3 tablespoons of 4 Synthetic SAE15W-40/SF engine oil.
Cleaning and Storage Fog the Engine If you choose not to use Fogging Oil,perform the following procedure. 1.Support the front end of the machine,so the engine is level or tilted slightly rearward. 2.Remove the spark plug.Rotate the piston to BDC and pour approximately two ounces of oil into the cylinder. 3.Apply dielectric grease to the inside of the spark plug cap and install the cap onto the plug. 4.
Cleaning and Storage Battery Storage Remove the battery from the vehicle and ensure that it's fully charged before placing it in storage. Engine Anti-freeze Test engine coolant strength and change if necessary.Coolant should be replaced every two years. Storage Area/Covers Set the tire pressure and safely support the ATV/Quadricycle with the tires 3050mm off the ground.Be sure the storage area is well ventilated, and cover the machine with a ATV/Quadricycle cover. NOTE:Do not use plastic or coated material.
Cleaning and Storage Chrome Wheel Care(if equipped) Proper maintenance will protect chrome wheels from corrosion,preserve wheel life and ensure a "like new" appearance for many years. 1.Wash chrome rims frequently.Use a mild detergent to remove any salt,dirt,mud or grime.Never use abrasive cleaners on plated or painted surfaces. 2.Polish the clean chrome wheels periodically.Use an automotive grade chrome polish. 3.Routinely and liberally apply a weather resistant wax to each polished chrome wheel.
TROUBLESHOOTING Drive belt and cover problems Solution Possible Cause Driving the ATV/Qudricycle onto a pickup or tall trailer in high range Starting out going up a steep incline Shift transmission to low range during loading of the ATV/Qudricycle to prevent belt burning. When starting out on an incline,use low range or dismount ATV/Qudricycle(after first applying the park brake) and perform the K-turn as discribed on page 67. Driving at low RPM (at approximately5-11 MPH) Use low range more frequently.
Drive belt and cover problems Solution Possible Causes Shift Stuck in mud or snow the aggressive Excessive transmission throttle throttle to low application may cause range to and engage loss of use fast, .WARNING: carefully clutch control and vehicle overturn . Climbing over large objects from a stopped position. Shift the transmission to low range,and carefully use fast,brief,aggressive throttle application to engage clutch.
Contact your dealer for service if you're unable to identify solutions us ing following charts. Engine doesn't Turn Over Possible Cause Solution Tripped circuit breaker Low battery voltage Reset the breaker Recharge battery to 12.
Engine turns over, fails to start Possible causes Solution Crankcase filled with water or fuel Immediately see your dealer Clogged fuel filter Low battery voltage Replace the filter Mechanical failure See your dealer Recharge battery to 12.
Engine Backfires Possible Cause Solution Weak spark from spark plugs Inspect,clean and/or replace spark plug Incorrect spark plug gap or heat range Set gap to specified or replace plugs Old or non-recommended fuel Replace with new fuel Incorrectly installed spark plug wires See your dealer Incorrect ignition timing See your dealer Mechanical failure See your dealer Engine Runs Irregularly,Stalls or Misfires Possible cause Fueled or defective spark plug Solution Inspect,clean and/or replace sp
Engine Runs Irregularly,Stalls or Misfires Possible Weak Spark Cause Kinked or plugged fuel vent line Solution Incorrect fuel Inspect and replace Replace with recommended fuel Clogged air filter Inspect,clean and repalce Reverse speed limiter malfuntion See your dealer Other mechanical failure See your dealer Possible lean fuel mixture cause Solution Low or contaminated fuel Low octane fuel Add or change fuel,clean the fuel system Low pressure of fuel pump Incorrect jetting Replace fuel pump
Engine Stops or Loses Power Possible cause Solution Outl of fuel Refuel Kinked or plugged fiel vent line Inspect and replace Water present in fuel Replace with new fuel Defective fuel pump or fuel pump relay Inspect/replace Fouled or defective spark plugs Inspect and replace plug if necessary Worn or defective spark plug wires See your dealer Incrrect spark plug gap ot heat range Set gap to specified or replace plugs Loose ignition connections Low battery voltage Check all connections and t
Engine Stops or Loses Power Possible cause Solution Clean radiator screen and core if equipped Overheated engine Clean enginen exterior See your dealer - 131-
PCODE LIST MSE3.0 No PCODE Faiure Analysis Heating Control Circuit Failure Type Of Oxygen Sensor is open circuit.
Signal Circurt Voltage of Oxygen Sensor is too high. Oxygen Sensor is worn out. Signal Circurt Failure of Oxygen Sensor self studying found closing loop control air fuel ratio is unusual when making End of line Testing self studying found closing loop control air fuel ratio is too thin when making End of Line Testing self studying found closing loop control air fuel ratio is too thick when making End of Line Testing Control Circurt of Cylinder 1 injector is open circurt.
Rotate Speed of Idle Control is faster than that of Target Idle. Pin of Stepping Motor Driver is short to ground. Pin of Stepping Motor Driver is short to power. Pin of Stepping Motor Driver is open circurt. Votage Signal of Battery is unusual. Unusual Failure Low Votage of Battery Minimum Failure High Votage of Battery Maximum Failure ECU Code Failure Control Circurt of Fuel Pump Relay is incomplete. Signal Failure Control Circurt of Fuel Pump Relay is short-to-ground.
Main Technical Data Model Data Overall Size (mm) Wheel Base (mm) CF500-5C/CF625-C CF500-5B/CF625-B 2100×1180×1230 2300×1180×1230 1290 1490 Min. Ground Clearance (Load) (mm) Nearest Min. Turning Diameter (L,R) (mm) Furthest Min.
Main Technical Data Model Data Weight(kg) CF500-5C/CF625-C 344 358 Front Track(mm) 920 Rear Track(mm) 880 Model Data CF500-5B/CF625-B CF500-5C/CF625-C Fuel Capacity(L) 18 Reserve Fuel Capacity(L) 4 Fuel Type (Kerb Mass) Axle Loaded Front Axle (kg) Rear Axle (kg) - 136- CF500-5B/CF625-B Unleaded Gasoline 93 or Above 183 194 161 164
Main Technical Data Model Data Frame Type Caster(mm) Wheel Rake(o) CF500-5B/CF625-B CF500-5C/CF625-C Steel 26.5 Front Wheel Camber：1±0.5（Unloaded） Rear Wheel Camber：1±0.5（Unloaded） o Caster Angel 9 52' Kingpin Offset(mm) 26.
Main Technical Data Model Data CF500-5B/CF625-B CF500-5C/CF625-C Front Wheel (mm) Plate 12×6.0AT/ Light Alloy 12×6.0AT Rear Wheel (mm) Plate 12×7.5AT/ Light Alloy 12×7.
Main Technical Data Model Data Type Front Brake Operation Mode Type Rear Brake operation Mode Front Wheel Tire Pressure (kpa) Rear Wheel Front, Rear Suspension CF500-5B/CF625-B CF500-5C/CF625-C Hydraulic Disc Manual Opeartion Hydraulic Disc Manual and Foot Connection Operation Front Wheel35，Rear Wheel30 IIndependent Swing Arm - 139-
Main Technical Data Model CF500-5C/CF625-C CF500-5B/CF625-B Data Steering Gear Mechanial Type Absorber(Front, Rear) Helix-Spring-Damped Type Max. Turning Angle, Fr.
Main Technical Data Model CF500-5C/CF625-C CF500-5B/CF625-B Data Coolant Capacity （L） Shift Operation Mode Muffler Type Initial：2.0；Replacement：1.
Main Technical Data Model CF500-5C/CF625-C CF500-5B/CF625-B Data Battery Battery Type Front Light Bulbs, Head Light Quantity, Type 12V18AH/12V30AH 12V 5Wx2; W5W H1/H3 12V55W×4 Turning Light Amber Lamp Cover:R10W12V10W Transparent Lamp Cover:RY10W12V10W Rear Brake/ Rear Light Red：R21/5W12V21W/5W 2 pcs Engine： -142 - Lead-acid Battery Single Cylinder, Liquid-Cooled,SOHC、4-Stroke Bore×Stroke（mm）：87.5×82 Displacement（ml）：493 Compression Ratio：10.
ZHE JIANG CFMOTO POWER CO.,LTD. Add: NO.116 Wuzhou Road, Yuhang Economic Devel opment Zone, Hangzhou, Zhejiang 311100, China Tel: 0571-89265684 Fax:0571-89265696 Website: WWW.cfmoto.
