User Instructions

ManualsBrandsChamberlain Group ManualsElectronicsTouch Pad Transmitter

To comply with FCC/IC rules, adjustment or modification of receiver and/or

transmitter is prohibited, except for changing the code setting and replacing the

transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Installation

Choose a convenient

location for installation.

It should be at eye

level, reachable by the

shortest person who

will use it, and within

sight of the door.

For a one-piece door,

use the optional

location shown in the

illustration (on the edge

of the door jamb) to avoid injury as the door

swings up and out.

Test the reception of the Keyless

Entry by operating your opener

from the selected location.

Change the location if necessary.

Remove the battery compartment

cover to access the bottom

mounting hole:

• Insert a small phillips screw driver

into the small hole at the bottom of

the cover and gently pull outward to

loosen.

• Slide the cover down to remove.

Center the keypad at eye level against the selected

location. Mark 4-1/4" up the centerline from the bottom and

drill a 1/8" pilot hole. Install top mounting screw, allowing

1/8" to protrude above surface. Position keypad on screw

head and adjust for snug fit.

With cover open so bottom mounting hole is visible, use a

punch to mark hole. Remove keypad and drill 1/8" pilot

hole. Replace keypad and complete installation with

bottom screw, using care to avoid cracking plastic housing.

Do not overtighten.

To replace the battery cover, insert the lip at the top and

snap in place.

Side two contains instructions for changing the personal

entry password and setting a temporary password.

Door Jamb Edge

(Optional Location

for 1-Piece Door)

Keypad

Door Jamb Face

SECTIONAL DOOR ONLY

KEYPAD MUST BE INSTALLED

WITHIN SIGHT OF THE DOOR

Exterior Front Wall

1-Piece or

Sectional Door

Typical

Sectional Door

Installation

Setting the Personal Entry Password

We recommend that you program your personal password

now, before you install the Keyless Entry. Then you can

test the reception at the mounting location before you

proceed further.

1. Choose a 4-digit personal entry password using the

numbers from 0 to 9 (a number can be used more than

once, for example, 4,0, 4,1).

2. Press the four buttons for the

password, then press and

hold

the Enter button. The

indicator light on the door

opener panel will blink.

3. Press and release the “Smart”

(learn) button on the door

opener panel. After the

opener lights blink, release

the Enter button.

Test by pressing the the password, then press Enter. The

door should begin to move.

You may also program the Keyless Entry from a

multifunction door control, as follows:

With the door closed,

enter the four digit password

desired, then press and hold Enter.

2. Press and hold the light button on the door control.

3. Press and hold the door control push bar.

4. After the opener lights blink, release all buttons.

SECURITY✚

Garage Door Opener

"Smart" (learn)

Button

Indicator Light

Children operating or playing with a garage door

opener can injure themselves or others.

The

garage door could close and cause serious injury

or death.

Do not allow children to operate the wall

push button(s) or remote control(s).

A moving garage door could injure or kill someone

under it.

Activate the opener only when you can see

the door clearly, it is free of obstructions, and is

properly adjusted.

WARNING

433MHz Wireless Keyless Entry

Features

For use with any SECURITY✚

compatible garage door opener

receiver.

Personalized Password: Up to

10,000 possible combinations. Password

can be easily changed if desired.

Temporary password: Can be added for visitors

or service persons. This temporary password can be

limited to a programmable number of hours or a

programmable number of entries.

Rolling Code: While your password remains constant until

you change it, the code between the Keyless Entry and the

receiver changes with each use, randomly accessing over

100 billion new codes.

Operation: Opener activates when 4-digit password and

Enter button is pressed.

If wrong numbers are accidentally pressed, correction can be

made immediately. The Enter button will transmit only the last

four digits.

The Keypad will blink for 15 seconds after the password is

transmitted. During that time the Enter button can be used to

stop or reverse the door travel.

Battery

Bottom

mounting hole

Battery

Cover

Summary of content (4 pages)

PAGE 1
433MHz Wireless Keyless Entry To comply with FCC/IC rules, adjustment or modification of receiver and/or transmitter is prohibited, except for changing the code setting and replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. WARNING Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the wall push button(s) or remote control(s).
PAGE 2
Changing the Personal Entry Password Press the four buttons for the present password, then press and hold the # button. The opener light will blink twice. Release the # button. Press the new 4-digit password you have chosen, then press Enter. The opener light will blink once when the password has been learned. Test by pressing the new password, then press Enter. The door should move. 2. Press the temporary 4-digit entry password you have chosen, then press Enter. The opener light will blink four times. 3.
PAGE 3
433MHz Système d’ouverture sans clé Conformément aux règles de la FCC/IC, il est interdit de régler ou de modifier ce récepteur et/ou émetteur, sauf pour modifier le code ou pour remplacer la pile. IL N’EXISTE AUCUNE AUTRE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. AVERTISSEMENT Les enfants qui utilisent ou qui jouent avec un ouvreporte de garage risquent de se blesser et de blesser les autres. La porte risque de se fermer et de causer de graves blessures, voire la mort.
PAGE 4
Modification du mot de passe personnel Appuyer sur les quatre boutons pour le mot de passe présent, appuyer sur le bouton # et le tenir. L’éclairage de l’ouvre-porte clignotera deux fois. Relâcher le bouton. Introduire le nouveau mot de passe à quatre chiffres choisi, puis appuyer sur Enter. L’éclairage de l’ouvre-porte clignotera une fois une fois le mot de passe mémorisé. Faire un essai en introduisant le nouveau mot de passe, puis appuyer sur Enter. La porte devrait bouger.