User Manual

ManualsBrandsChamberlain Group ManualsElectronicsKeypad Access Controller

OVERVIEW

The Wireless Commercial Keypad comes with one 9V Lithium battery, instructions, and two keys. A wireless

signal is transmitted when a valid 4-digit PIN and the # key is pressed. A long tone will sound. The keypad

backlight will illuminate for 15 seconds when any key is pressed. If an invalid PIN or partial PIN is accidentally

entered, an error tone will sound. The Wireless Commercial Keypad is compatible with the brands of commercial

door and gate operators listed in the table below.

Wireless Commercial Keypad

Models KPW5 and KPW250

MODEL FREQUENCY AND ENCRYPTION PIN CAPACITY

KPW5 LiftMaster Security+ 2.0™ Default

Tri-band 390 MHz, 315 MHz, and 310 MHz

Up to 5 permanent PINs and

Up to 10 unique temporary PINs

KPW250 LiftMaster Security+ 2.0™ Default

Tri-band 390 MHz, 315 MHz, and 310 MHz

Up to 250 permanent PINs and

Up to 10 unique temporary PINs

LiftMaster Security+

315 MHz

LiftMaster Security+

390 MHz

Linear Multi-Code 300 MHz

Speciﬁ cations

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9V lithium battery

Operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . -40°F to 140°F (-40°C to +60°C)

Storage and shipping temperature range . . . . . . . . . . . . . . .-40°F to 140°F (-40°C to +60°C)

Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .NEMA 3R

KPW5 KPW250

Summary of content (5 pages)

PAGE 1
Wireless Commercial Keypad Models KPW5 and KPW250 OVERVIEW The Wireless Commercial Keypad comes with one 9V Lithium battery, instructions, and two keys. A wireless signal is transmitted when a valid 4-digit PIN and the # key is pressed. A long tone will sound. The keypad backlight will illuminate for 15 seconds when any key is pressed. If an invalid PIN or partial PIN is accidentally entered, an error tone will sound.
PAGE 2
INSTALLATION To prevent possible SERIOUS INJURY or DEATH from a moving gate or door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. 1.
PAGE 3
PROGRAM TO OPERATOR LiftMaster NOTE: The Master Code and a PIN need to be set before the gate operator can be programmed. See Basic Programming, page 2. KPW5 - The frequency and encryption are set at the factory. Proceed to Step 4. KPW250 - The frequency and encryption are set at the factory for LiftMaster Security+ 2.0 (tri-band 310, 315, and 390 MHz) operators. Proceed to Step 4. For LiftMaster Security+ (315 MHz or 390 MHz), the frequency and encryption need to be set. Proceed to Step 1. 1.
PAGE 4
ADDITIONAL PROGRAMMING The Wireless Commercial Keypad must be put into programming mode prior to any of the programming steps below unless otherwise indicated. Set Temporary PIN A temporary 4-digit PIN can be programmed to allow access to visitors (maximum of 9 uses). The temporary PIN cannot be the same as any previously programmed PIN. The keypad will store up to 10 unique temporary PINs. Programming Step Keystroke Combination (Master Code) # 1. Enter program mode 2.
PAGE 5
BATTERY To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 9V Lithium battery. • DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate. The 9V Lithium battery should produce power for up to 5 years. To replace the battery: 1. Unlock and remove the faceplate from the mounting plate. 2.