User's Manual

ManualsBrandsChamberlain Group ManualsElectronicsPart 15 Spread Spectrum Transmitter Transceiver

REAR INSTALLATION ONLY

STANDARD INSTALLATION ONLY

Open the gate and line up the front bracket so the chain will be level with the

idler pulley and parallel to the ground. Weld the front bracket in this position.

Close the gate and line up the rear bracket so the chain will be level with the

idler pulley and parallel to the ground. Weld the rear bracket in this position.

Route the chain through the operator.

Connect the chain to the brackets using the eye bolt hardware. Chain should

not be too tight or have excessive slack.

DO NOT run the operator until instructed.

NOTE: The chain should have no more than 1 inch of sag for every 10 feet of chain

length.

DO NOT run the operator until instructed.

The chain should have no more than 1 inch of sag for every 10 feet of chain

length.

NOTE: This installation will require two extra idler pulleys. Make sure all

exposed pinch points are guarded. Refer to Gate Construction Information on

page 4.

Move the back pulley to the bottom hole in the operator.

Close the gate and align the bottom bracket so the chain will be level

with the bottom idler pulley and parallel to the ground. Weld the bottom

bracket in this position

Align the top bracket so the chain will be level with the top idler pulley

and parallel to the ground. Weld the upper bracket in this position.

Route the chain through the operator.

Connect the chain to the brackets using the eye bolt hardware. Chain

should not be too tight or have excessive slack.

STANDARD INSTALLATION ONLY + REAR INSTALLATION ONLY

INSTALLATION

Idler Pulley MUST have safety cover.

Summary of content (8 pages)

PAGE 1
INSTALLATION STANDARD INSTALLATION ONLY + REAR INSTALLATION ONLY STANDARD INSTALLATION ONLY DO NOT run the operator until instructed. Open the gate and line up the front bracket so the chain will be level with the idler pulley and parallel to the ground. Weld the front bracket in this position. 1 2 3 4 2 1 Close the gate and line up the rear bracket so the chain will be level with the idler pulley and parallel to the ground. Weld the rear bracket in this position.
PAGE 2
WIRING WIRE THE ENTRAPMENT PROTECTION DEVICES + EARTH GROUND ROD WIRE THE ENTRAPMENT PROTECTION DEVICES Entrapment protection devices are required. Refer to page 5 for more information regarding application. To prevent SERIOUS INJURY or DEATH from a moving gate: • Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate. • Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
PAGE 3
WIRING POWER WIRING POWER WIRING This operator can be wired for either 120 Vac or 240 Vac or a solar panel (not provided). Follow the directions according to your application. For dual gate applications, power will have to be connected to each operator. Main power supply and control wiring MUST be run in separate conduits.
PAGE 4
WIRING POWER WIRING POWER WIRING CONTINUED... 120 VAC AND 240 VAC Turn off the AC power from the main power source circuit breaker. Run the AC power wires to the operator. Remove the junction box cover. Connect the green wire to the earth ground rod wire using a wire nut. Connect the white wire to NEUTRAL using a wire nut. Connect the black wire to HOT using a wire nut.
PAGE 5
WIRING DUAL GATES ONLY DUAL GATES ONLY There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Wired dual gate applications will have a longer battery standby time than wireless applications. WIRED DUAL GATES Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables. Trench across driveway to bury the extension cable.
PAGE 6
WIRING DUAL GATES ONLY + CONNECT BATTERIES DUAL GATES ONLY BIPART DELAY The BIPART DELAY switch is used only with dual gate applications where a mag-lock, solenoid lock, or decorative overlay would require one gate to close before the other. Factory default is OFF. 1 LE BIPART DELAY LOSE Turn the BIPART DELAY switch ON according to your application: the operator with the bipart delay switch ON will delay from the close limit when opening and be the first to close from the open limit.
PAGE 7
ADJUSTMENT LIMIT SETUP LIMIT SETUP To reduce the risk of SEVERE INJURY or DEATH: • Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a moving gate. • Too much force on gate will interfere with proper operation of safety reversal system. • NEVER increase force beyond minimum amount required to move gate. • NEVER use force adjustments to compensate for a binding or sticking gate.
PAGE 8
ADJUSTMENT FORCE ADJUSTMENT + OBSTRUCTION TEST FORCE ADJUSTMENT 1 TEST BUTTONS XMITTER SET OPEN SET CLOSE LEARN BIPART DELAY TEST BUTTONS STOP COMMON CLOSE 10 60 OPEN EXIT MAX BATT LOW BATT CHARGING GATE MOVING ACC PWR OVLD DIAGNOSTIC CODES SHADOW + INTERRUPT + - OPEN EYES EDGE SET OPEN SET CLOSE Open and close the gate with the test buttons. 3 Perform the “Obstruction Test” after every force setting adjustment. NETWORK COMM LINK B A N.C. N.O. COM ACCESSORY POWER ON SW.