User's Manual

ManualsBrandsChamberlain Group ManualsElectronicsPart 15 Spread Spectrum Transmitter Transceiver

SET OPEN

SET CLOSE

MOVE

GATE

OFF

180

MIN

MAX

(SECONDS)

OFF

OPEN

STOP

INPUT POWER

BATT CHARGING

TIMER

GATE MOVING

BATT LOW

ACC PWR OVLD

DIAGNOSTIC

CODES

BIPART

DELAY

LEARN

TEST

BUTTONS

TIMER

TO CLOSE

REVERSAL

FORCE

STATUS:

OPEN

STOP

COMMON

“FIRE

DEPT.”

OPEN

EXIT

SHADOW

INTERRUPT

COMM

LINK

B A

- +

EYES

EDGE

LOCK

N.O.

COM

N.C.

+ -

ACCESSORY

POWER

ON SW.

EXP.

BOARD

RESETENCODER

ID IN ALARM

SECURE / MANUAL

+ -

MOTOR

+ -

DC POWER

+ -

BATT

BATT FUSE

30A 32V

XMITTER

NETWORK

PRESS &

RELEASE

TO BEGIN

SETUP

LIMIT

OPEN

DC POWER FUSE

30A

32V

CLASS 2 SUPPLY

24 VOLTS

180

MIN

MAX

BATT LOW

ACC PWR OVLD

DIAG

REVERSAL

FORCE

NETWORK

Outside

Property

Inside

Property

Outside

Property

Inside

Property

Outside

Property

Inside

Property

FORCE ADJUSTMENT + OBSTRUCTION TEST

ADJUSTMENT

OBSTRUCTION TEST

After any adjustments are made, test the operator:

Open and close the gate with the test buttons, ensuring that the gate is

stopping at the proper open and close limit positions.

Place a solid object between the open gate and a rigid structure. (Ensure that

the gate, the solid object, and the rigid structure can withstand the forces

generated during this obstruction test.)

Run the gate in the close direction. The gate should stop and reverse upon

contact with the solid object. If the gate does not reverse off the solid object,

reduce the force setting by turning the force control slightly counter-clockwise,

as shown above in the “TO ADJUST THE FORCE” section.

Repeat the test for the open direction.

FORCE ADJUSTMENT

The operator is equipped with an automatic obstruction sensing feature. If the gate

encounters an obstruction during motion, the operator will automatically reverse

direction of the gate for a short time and then stop the gate.

Based on the length and weight of the gate it may be necessary to make force

adjustments. The force setting should be high enough that the gate will not reverse

by itself nor cause nuisance interruptions, but low enough to prevent serious injury to

a person. The force setting is the same for both the open and close gate directions.

Perform the “Obstruction Test” after every force adjustment.

TO ADJUST THE FORCE

Open and close the gate with the test buttons.

If the gate stops or reverses before reaching the fully open or closed position,

increase the force by turning the force control slightly clockwise.

If the gate cycles correctly limit-to-limit, reduce the force setting by turning the

force control slightly counter-clockwise and cycle the gate again. If the gate

now stops and reverses before reaching the fully open or closed position,

increase the force by turning the force control slightly. Repeat as needed.

Perform the “Obstruction Test” after every force setting adjustment.

The basic installation is complete.

SET OPEN

SET CLOSE

MOVE

GATE

OFF

180

MIN

MAX

(SECONDS)

OFF

OPEN

STOP

INPUT POWER

BATT CHARGING

TIMER

GATE MOVING

BATT LOW

ACC PWR OVLD

DIAGNOSTIC

CODES

BIPART

DELAY

LEARN

TEST

BUTTONS

TIMER

TO CLOSE

REVERSAL

FORCE

STATUS:

OPEN

STOP

COMMON

“FIRE

DEPT.”

OPEN

EXIT

SHADOW

INTERRUPT

COMM

LINK

B A

- +

EYES

EDGE

LOCK

N.O.

COM

N.C.

+ -

ACCESSORY

POWER

ON SW.

EXP.

BOARD

RESETENCODER

ID IN ALARM

SECURE / MANUAL

+ -

MOTOR

+ -

DC POWER

+ -

BATT

BATT FUSE

30A 32V

XMITTER

NETWORK

PRESS &

RELEASE

TO BEGIN

SETUP

LIMIT

OPEN

DC POWER FUSE

30A

32V

CLASS 2 SUPPLY

24 VOLTS

MAX

OPEN

STOP

DIAGNOSTIC

TEST

BUTTONS

RSAL

RCE

XMITTER

NETWORK

SET OPEN

SET CLOSE

MOVE

GATE

OFF

180

MIN

MAX

(SECONDS)

OFF

OPEN

STOP

INPUT POWER

BATT CHARGING

TIMER

GATE MOVING

BATT LOW

ACC PWR OVLD

DIAGNOSTIC

CODES

BIPART

DELAY

LEARN

TEST

BUTTONS

TIMER

TO CLOSE

REVERSAL

FORCE

STATUS:

OPEN

STOP

COMMON

“FIRE

DEPT.”

OPEN

EXIT

SHADOW

INTERRUPT

COMM

LINK

B A

- +

EYES

EDGE

LOCK

N.O.

COM

N.C.

+ -

ACCESSORY

POWER

ON SW.

EXP.

BOARD

RESETENCODER

ID IN ALARM

SECURE / MANUAL

+ -

MOTOR

+ -

DC POWER

+ -

BATT

BATT FUSE

30A 32V

XMITTER

NETWORK

PRESS &

RELEASE

TO BEGIN

SETUP

LIMIT

OPEN

DC POWER FUSE

30A

32V

CLASS 2 SUPPLY

24 VOLTS

MAX

OPEN

STOP

DIAGNOSTIC

TEST

BUTTONS

RSAL

RCE

XMITTER

NETWORK

Summary of content (19 pages)

PAGE 1
ADJUSTMENT FORCE ADJUSTMENT + OBSTRUCTION TEST FORCE ADJUSTMENT 1 TEST BUTTONS XMITTER SET OPEN SET CLOSE LEARN BIPART DELAY TEST BUTTONS STOP COMMON CLOSE 10 60 OPEN EXIT MAX BATT LOW BATT CHARGING GATE MOVING ACC PWR OVLD DIAGNOSTIC CODES SHADOW + INTERRUPT + - OPEN EYES EDGE SET OPEN SET CLOSE Open and close the gate with the test buttons. 3 Perform the “Obstruction Test” after every force setting adjustment. NETWORK COMM LINK B A N.C. N.O. COM ACCESSORY POWER ON SW.
PAGE 2
PROGRAMMING REMOTE CONTROLS + ERASE ALL CODES REMOTE CONTROLS A combined total of 50 Security MAX remote controls and keyless entry PINs can be programmed to the operator. 1 TO ADD OR REPROGRAM A REMOTE CONTROL (NOT PROVIDED) Press and release the LEARN button (green XMITTER LED will light). LEARN BIPART DELAY SET OPEN SET CLOSE TEST BUTTONS NETWORK ON REVERSAL FORCE (SECONDS) 10 60 STATUS: STOP “FIRE DEPT.
PAGE 3
OPERATION RESET SWITCH + REMOTE CONTROL RESET SWITCH The reset switch is located on the front of the operator and serves several functions. Toggling the reset switch will stop a moving gate during a normal open/close cycle, like a stop button. The operator does not need to be reset after doing this. PROGRAMMING LIMITS RESET If a mistake is made while programming the limits toggle the reset switch to start over.
PAGE 4
ADDITIONAL FEATURES GATE OPERATOR SETUP EXAMPLES GATE OPERATOR SETUP EXAMPLES The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary secondary entrapment protection systems.
PAGE 5
ADDITIONAL FEATURES CONTROL BOARD OVERVIEW CONTROL BOARD OVERVIEW SET OPEN Button The SET OPEN button sets the OPEN limit. See Adjust Limits section. SET CLOSE Button The SET CLOSE button sets the CLOSE limit. See Adjust Limits section. MOVE GATE Button The MOVE GATE buttons will either open or close the gate when the operator is in Limit setting mode. See Adjust Limits section. BIPART DELAY Switch The Bipart delay switch is used only for dual gates. See Bipart Delay section.
PAGE 6
ADDITIONAL FEATURES ACCESSORY FEATURES ON CONTROL BOARD ACCESSORY FEATURES ON CONTROL BOARD A Open Input (& common) (3-Button Control Station, 4 terminals total) Open command - opens a closed gate. Hard open (maintained switch overrides external safeties and resets alarm condition) If maintained, halts Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate. B Close Input (& common) (3-Button Control Station, 4 terminals total) Close command - closes an open gate.
PAGE 7
ADDITIONAL FEATURES EXPANSION BOARD OVERVIEW EXPANSION BOARD OVERVIEW To AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to the AUX relay contact terminal blocks. QUICK CLOSE Switch OFF: No change to the gate's normal operation. ON: When Interrupt loop is deactivated it causes an opening or a stopped gate to close. AC FAIL OPEN/BATT Switch OPEN: Loss of AC power will cause gate to immediately OPEN and remain OPEN until AC power is restored.
PAGE 8
ADDITIONAL FEATURES ACCESSORY FEATURES ON EXPANSION BOARD ACCESSORY FEATURES ON EXPANSION BOARD A Open Input (& common) (3-Button Control Station, 4 terminals total) Open command - opens a closed gate. Soft close (maintained switch does not override external safeties and does not reset alarm condition) If maintained, halts Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate.
PAGE 9
ACCESSORIES ENTRAPMENT PROTECTION DEVICES MISCELLANEOUS PHOTOELECTRIC SENSORS (NON-CONTACT) HEATER The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the operator. Includes mounting brackets. Models AOMRON (retro-reflective), RETROAB (retro-reflective), CPS-UN4 (through beam) Keeps operator gearbox and batteries at suitable temperature when outside temperature is below 0°F for extended periods of time.
PAGE 10
MAINTENANCE MAINTENANCE CHART + BATTERIES + DRIVE CHAIN MAINTENANCE CHART Disconnect all power (AC, solar, battery) to the operator before servicing. The operator's AC Power switch ONLY turns off AC power to the control board and DOES NOT turn off battery power. ALWAYS disconnect the batteries to service the operator.
PAGE 11
TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS The control board is equipped with many LEDs that have a variety of functions. The control board LEDs indicate the status of the operator, assist with programming, and diagnose potential problems with the operator.
PAGE 12
TROUBLESHOOTING CONTROL BOARD LEDS CONTROL BOARD LEDS DIAGNOSTIC CODES LEDS YELLOW DIAGNOSTIC LED RED DIAGNOSTIC LED # BLINKS MEANING CORRECTION # BLINKS MEANING CORRECTION 1 BLINK Low Power Mode (not an error) 2 BLINKS Current Sense 2 BLINKS ID resistor failure Check ID resistor wiring, clear limit settings and reset limits Motor control circuit fault, replace control board 3 BLINKS FET Failure 3 BLINKS Exceeded Maximum Run Timer Check gate travel, if necessary adjust force setting
PAGE 13
TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Operator does not run and diagnostic LED not on. a) b) c) d) No power to control board Open fuse If on battery power only, low or dead batteries Defective control board a) b) c) d) Check AC and battery power Check fuses Charge batteries by AC or solar power or replace batteries Replace defective control board Control board powers up, but motor does not run.
PAGE 14
TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Gate stops during travel and reverses immediately. a) Check DIAGNOSTIC LEDs b) Inherent force obstruction detection c) External Entrapment Protection Device activation d) Control (Open, Close) becoming active e) Vehicle loop detector active f) Low battery voltage a) Use Diagnostic code to identify issue b) Check for obstruction in gate’s path or travel.
PAGE 15
TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Obstruction in gates path does not cause gate to stop and reverse a) Force setting too high a) Adjust force setting. Retest that obstruction in gate’s path causes gate to stop and reverse direction. Photoelectric sensor does not stop or reverse gate. a) Incorrect photoelectric sensor wiring b) Defective photoelectric sensor a) Check photoelectric sensor wiring.
PAGE 16
TROUBLESHOOTING TROUBLESHOOTING CHART FAULT POSSIBLE CAUSES CORRECTIONS Accessories connected to Accessory power not working correctly, turning off, or resetting. a) Accessory power protector active b) Defective control board a) Disconnect all accessory powered devices and measure accessory power voltage (should be 23 – 30 Vdc). If voltage is correct, connect accessories one at a time, measuring accessory voltage after every new connection.
PAGE 17
Orange Black Bridge Rectifier Piezo Alarm 1/2 HP 24 Vdc Motor Reset /UL Release To Pin 5 Black - + - To Pin 1 Red White EMI FILTER/SURGE PROTECTION BOARD Gray Red - To Pin 2 White GND Black Blue Orange Black To Pin 6 Yellow Purple Brown Transformer 375 VA, 24V, 120V Red Identification Resistor White Red Switch/5A Breaker Butt Splice Black ON OFF Blue Yellow EXPANSION BOARD APS Encoder Red Black Primary/Secondary link to other gate operator Ground the shield of the cab
PAGE 18
Black Brown Transformer 375 VA, 24V, 120V - - Bridge Rectifier Orange Orange Black White EMI FILTER/SURGE PROTECTION BOARD Blue Gray Purple + - Red To Pin 2 To Pin 1 Piezo Alarm 1/2 HP 24 Vdc Motor Reset /UL Release To Pin 5 To Pin 6 Black Black Red Black Red Identification Resistor Green Install male insulated faston connectors on solar panel leads. Plug them into the female faston connectors that were connected to the bridge rectifier.
PAGE 19
WARRANTY 7 YEAR RESIDENTIAL / 5 YEAR COMMERCIAL CSL24V™ AND CSL24VH™ LIMITED WARRANTY The Chamberlain Group, Inc.