ARQ™ UNIVERSAL REMOTE CONTROL MODELS TM100 AND TM110 Activate up to three products, such as a garage door opener, MyQ® light controls, or gate operator with your ARQ™ Universal Remote Control. Each button must be programmed separately. STOP Read instructions thoroughly BEFORE beginning. If using the remote control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors.
COMPATIBILITY Compatible with most garage door openers manufactured by Chamberlain®, LiftMaster®, Sears Craftsman®, Garage Master®, Genie®, Linear®, Stanley®, Overhead Door®, Wayne Dalton®, Moore-O-Matic®, Do-It®, Master Mechanic®, Raynor®, True Value®, and Xtreme Garage™. For a complete list of compatible products, go to www.arq.chamberlain.com. PRODUCTS WITH SWITCHES The following instructions are for general programming.
BEFORE YOU BEGIN Locate the Program/LEARN button on your garage door opener (typically located on the back or side panel). Program/LEARN Button Your product may look different. Ladder may be needed. IMPORTANT: The remote control will activate your door during programming. Ensure door area is clear of ALL obstructions.
PROGRAMMING 1 Open garage door. 2 (In car): Press and hold the outer buttons on the remote control until the green LED stays solid (3-5 seconds). LED 3 (In garage): Press and release the Program/LEARN button on the garage door opener. 4 (In car): Press and release the button twice that you would like to program. 5 Wait until the garage door begins to close (up to 60 seconds). 6 Immediately press and release any button on the remote control (within 3 seconds of the door moving).
TEST Test the remote control by pressing the button you programmed in step 4. If the door does not move, repeat the programming steps or go to www.arq.chamberlain.com for additional instructions. BATTERY To prevent possible SERIOUS INJURY or DEATH: • DO NOT use a visibly damaged remote control battery. • DO NOT attempt to repair the remote control or battery. • If battery is swallowed, immediately notify doctor.
WARRANTY ONE YEAR LIMITED WARRANTY The Chamberlain Group, Inc warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. This device complies with Part 15 of the FCC rules and IC RSS-210.
TÉLÉCOMMANDE UNIVERSELLE ARQ™ MODÈLES TM100 ET TM110 Activez jusqu’à trois produits, comme un ouvre-porte de garage, des commandes d’éclairage MyQ® ou un actionneur de barrière avec votre télécommande universelle ARQ™. Chaque bouton doit être programmé séparément. ARRÊT Bien lire les instructions AVANT de commencer.
COMPATIBILITÉ Compatible avec la plupart des ouvre-portes de garage fabriqués par Chamberlain®, LiftMaster®, Sears Craftsman®, Garage Master®, Genie®, Linear®, Stanley®, Overhead Door®, Wayne Dalton®, Moore-O-Matic®, Do-It®, Master Mechanic®, Raynor®, True Value®, et Xtreme Garage™. Pour une liste complète des produits compatibles, aller à www.arq.chamberlain.com. PRODUITS AVEC COMMUTATEURS Les instructions suivantes s’appliquent à la programmation générale.
AVANT DE COMMENCER Trouver le bouton de programmation/d’apprentissage sur votre ouvre-porte de garage (situé en général sur le panneau arrière ou latéral). Bouton de programmation/ d’apprentissage Votre produit peut avoir une autre apparence. Il peut être nécessaire d’utiliser une échelle. IMPORTANT : La télécommande activera votre porte pendant sa programmation. S’assurer que la zone de la porte est libre de TOUTE obstruction.
PROGRAMMATION 1 Ouvrir la porte de garage. 2 (Dans l’auto) : Enfoncer et tenir les boutons extérieurs sur la télécommande jusqu’à ce que la DEL verte s’allume en continu (3 à 5 secondes). 3 (Dans le garage) : Enfoncer et relâcher le bouton de programmation/ d’apprentissage sur l’ouvre-porte de garage. 4 (Dans l’auto) : Enfoncer et relâcher deux fois le bouton que vous souhaitez programmer. 5 Attendre que la porte de garage commence à se fermer (jusqu’à 60 secondes).
ESSAI Tester la télécommande en appuyant sur le bouton programmé à l’étape 4. Si la porte ne commence pas à bouger, répéter les étapes de programmation ou aller à www.arq.chamberlain.com pour des instructions supplémentaires. PILE Pour éviter des BLESSURES GRAVES, VOIRE MORTELLES : • NE PAS utiliser une pile de télécommande visiblement endommagée. • NE PAS tenter de réparer la télécommande ou la pile. • Si une pile est avalée, aviser un médecin immédiatement.
GARANTIE GARANTIE LIMITÉE D’UN AN La société Chamberlain Group, Inc. garantit à l’acheteur initial que le produit est exempt de tout défaut de matériaux ou de fabrication pendant une période d’un an à compter de la date d’achat. AVIS: Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modification de ce récepteur. IL N’EXISTE AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR.