Users Manual Part 1

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

INDUSTRIAL DC

VEHICULAR SLIDE GATE OPERATOR

INSTALLATION MANUAL

• THIS PRODUCT MUST BE INSTALLED AND

SERVICED IN ACCORDANCE WITH THIS

MANUAL BY A TRAINED GATE SYSTEMS

TECHNICIAN ONLY.

• This operator is for use on vehicular passage

gates ONLY and not intended for use on

pedestrian passage gates.

• IHSL24UL and INSL24UL are intended

for use in Class II, III, andIV vehicular slide

gate applications.

• Visit LiftMaster.com to locate a professional

installing dealer in your area.

• This gate operator is compatible with myQ

and Security+ 2.0

accessories.

LiftMaster

300 Windsor Drive

Oak Brook, IL 60523

Access installation and technical support

guides or register this product

Send it in by texting

the photo to 71403.

Take a photo of the

camera icon including

the points ( ).

INSL24ULTECH

Models IHSL24UL I INSL24UL

Access installation and technical support

guides or register this product

Take a photo of the

camera icon including the

points ( ).

Send it in by texting the photo

to 71403.

PN: 40-39191-31-C

P/N: 40-39191-31-C

Printout Size

XX%

This printout is for indicating

color breaks only.

Do not use for color matching.

Do not measure for accuracy.

Rev. Date: 09/14/21

Printing & Finishing: Box Type: LABEL

Size: See Die

Colors:

K 202C Dieline

File Name:

3.5”

IHSL24ULTECH

ARTWORK: 40-39191-31-C

Summary of content (12 pages)

PAGE 1
INDUSTRIAL DC VEHICULAR SLIDE GATE OPERATOR Models IHSL24UL I INSL24UL INSTALLATION MANUAL • THIS PRODUCT MUST BE INSTALLED AND SERVICED IN ACCORDANCE WITH THIS MANUAL BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. • This operator is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates. • IHSL24UL and INSL24UL are intended for use in Class II, III, and IV vehicular slide gate applications. • Visit LiftMaster.com to locate a professional installing dealer in your area.
PAGE 2
TABLE OF CONTENTS SAFETY 2 Manual Disconnect...............................................................................29 Reset Button.........................................................................................29 Operator Alarm.....................................................................................30 Remote Control.....................................................................................30 Safety Symbol and Signal Word Review.......................................
PAGE 3
Usage Class Class II - Commercial/General Access Vehicular Gate A vehicular gate operator (or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other buildings accessible by or servicing the general public.
PAGE 4
SAFETY b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still Vehicular gate systems provide convenience and security. Gate moving. systems are comprised of many component parts. The gate operator is c. One or more non-contact sensors shall be located where the risk only one component. Each gate system is specifically designed for an of entrapment or obstruction exists, such as the perimeter individual application.
PAGE 5
SAFETY Gate Construction Information Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org. 1. General Requirements 3. Vehicular Horizontal Slide Gates 1.1 Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to ASTM F2200 for additional gate types. 3.
PAGE 6
INTRODUCTION Carton Inventory NOT SHOWN: Documentation Packet, Chain #40 - 30 feet with master link (INSL24UL ONLY), Chain #50 - 25 feet with master link (IHSL24UL ONLY), Eye Bolt Kit, Antenna MONITORED ENTRAPMENT PROTECTION DEVICES LiftMaster Monitored Retro-Reflective Photoelectric Sensor Model LMRRUL (1) Operator Front Warning Signs (2) Operator Back Installation Manual 5 ft.
PAGE 7
INTRODUCTION Operator Specifications INSL24UL IHSL24UL Class II, III, and IV Usage Classification Main AC Supply 120 Vac, 9.3 Amps including Accessory Outlets OR 240 Vac, 1.8 Amps Optional Transformer Kit When Optional Transformer Kit Model 3PHCONV is installed in the field, operator is rated 120 Vac, 13.0 Amps including Accessory Outlets OR 240 Vac, 3.7 Amps 208/240/480/575 VAC, 5.2/4.5/2.3/1.
PAGE 8
INTRODUCTION Site Preparation Check the national and local building codes BEFORE installation. Refer also to the Site Planning Safety Checklist in the Appendix. Safety Entrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate application. Install a warning sign (two provided) on the inside and outside of the property, where easily visible.
PAGE 9
INSTALLATION • To AVOID damaging gas, power or other underground utility lines, contact underground utility locating companies BEFORE digging more than 18 inches (46 cm) deep. • To prevent damage to the operator or gate, DO NOT drive the limit (nuts) actuators on the shaft past their normal positions. Step 1 Install the Operator Check the national and local building codes before installation. Install With Adjustable Rails 1. Locate and anchor two posts made of 3" (7.
PAGE 10
INSTALLATION Install Without Adjustable Rails Check the national and local building codes before installation. NOTE: The rails will have to be removed for retro-fit installations. 1. Locate and anchor two posts made of 3" (7.6 cm) outer diameter heavy walled pipe. Posts should be parallel and square to the gate. 2. Locate electrical conduit, as required, prior to pouring concrete. 3. Remove the rails from the sides of the operator. 4. Secure Operator to posts using four 3" (7.6cm) U-bolts and hardware.
PAGE 11
INSTALLATION Step 2 Attach the Chain DO NOT run the operator until instructed. 1. Mount gate brackets to the vertical front and rear posts of the gate. 2. Open operator door. 3. Locate the black T-shaped manual release handle attached to the gearbox in the bottom of the cabinet. Pull firmly until it latches into place. 4. Ensure that the drive and idler sprockets are in line with each other.
PAGE 12
INSTALLATION To prevent SERIOUS INJURY or DEATH from a moving gate: • ALL gate operator systems REQUIRE two independent entrapment protection systems for each entrapment zone. • Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate. • Entrapment protection devices MUST be located to protect in BOTH the open and close gate cycles.