Users Manual Part 2

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

Install entrapment protection devices according to the UL 325 Entrapment Protection Requirements section, see page 3. Use the Site Planning Safety

Checklist in the appendix, to identify entrapment zones that will result from the installation. See Accessories for approved entrapment protection devices.

Requirements

1. Install entrapment protection devices for ALL entrapment zones.

This operator has an inherent entrapment protection device built-in.

The installer MUST provide one additional entrapment protection

device for each entrapment zone.

The operator will NOT run unless a minimum of two external

devices are connected; one in the open direction and one in the

closed direction.

3. Test ALL entrapment protection devices AFTER installing the

operator, refer to the manual provided with your entrapment

protection device. Test the inherent entrapment protection by

following the Obstruction Test instructions page 23.

See Wire Entrapment Protection Devices page 14.

Illustration is for example only; your site may have additional entrapment

zones which MUST be protected.

Secure Side

Public Side

Gap between vertical

bars MUST be less

than 2-1/4" (57 mm)

Interior posts,

non-pinch rollers (2x)

Place warning signs on both

sides of the gate in clear view

Take a photograph of the complete installation site for your records

Any gap larger than 2-1/4" (57 mm) between

gate and ﬁxed objects MUST be protected.

Install edge sensors where gap between post

and gate creates an entrapment zone.

Pedestrian gate located near the slide gate.

Make sure a separate pedestrian entrance is

available and the path is clearly designated.

6' (1.8 m)

minimum

Photoelectric sensor

(close direction)

Photoelectric sensor

(close direction)

Photoelectric sensor (open direction)

Left hand

gate opening

Edge sensor

Earth ground

Illustrations provided by DASMA Gate Systems Safety Guide

INSTALLATION

Summary of content (4 pages)

PAGE 1
INSTALLATION Install entrapment protection devices according to the UL 325 Entrapment Protection Requirements section, see page 3. Use the Site Planning Safety Checklist in the appendix, to identify entrapment zones that will result from the installation. See Accessories for approved entrapment protection devices. Requirements 1. Install entrapment protection devices for ALL entrapment zones. This operator has an inherent entrapment protection device built-in.
PAGE 2
INSTALLATION Wire Entrapment Protection Devices There are three options for wiring external entrapment protection devices depending on the specific device and how the device will function. Refer to the manual included with your entrapment protection device for more information. These entrapment protection device inputs are for monitored devices, which include pulsed photoelectric sensors, resistive edge sensors, and pulsed edge sensors.
PAGE 3
INSTALLATION Step 4 Earth Ground Rod To operator Use the proper earth ground rod for your local area. The ground wire must be a single, whole piece of wire. Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length. NOTE: If the operator is not grounded properly the range of the remote controls will be reduced and the operator will be more susceptible to lightning and surge damage.
PAGE 4
INSTALLATION IHSL24UL MAXIMUM WIRE LENGTH STANDARD OPERATOR 3PHCONV kit powering operator + heater + 1 Amp on outlets AMERICAN WIRE GAUGE (AWG) 120 VAC, 13 A (includes fully loaded outlets) 120 VAC, 7 A 240 VAC, 3.5 A 208 VAC, 5.2 A 240 VAC, 4.5 A 480 VAC, 2.3A 575 VAC, 1.9 A 14 75 140 600 330 440 1,700 2,500 12 120 225 900 525 700 2,700 4,000 10 200 360 1,440 840 1,100 4,400 6,300 8 300 600 2,300 1.