Users Manual Part 3

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

Step 6 Connect Batteries

7AH Batteries

The batteries are charged in the circuit by the integrated transformer.

1. Turn the AC power switch to OFF.

2. Turn the battery switch OFF .

3. Connect a jumper between the positive(+) terminal of the battery to

the negative terminal(-) of the other battery.

4. Connect the red battery wire from the operator to the positive(+)

terminal of the battery.

5. Connect the black battery wire from the operator to the negative (-)

terminal of the battery.

6. Turn the battery switch ON .

7. Turn the AC power switch to ON to restore AC power.

Battery Wiring

Red Wire

Black Wire

Jumper

33AH Batteries

The batteries are charged in the circuit by the integrated transformer.

The 33AH application requires battery harness K41-0102-000, see

Accessories.

1. Turn the AC power switch to OFF.

2. Turn the battery switch OFF.

3. Connect a jumper between the positive(+) terminal of the battery to

the negative terminal(-) of the other battery.

4. Connect the (+) terminal of the battery to the red battery wire from

the operator using the RED harness kit wire .

5. Connect the (-) terminal of the battery to the black battery wire from

the operator using the BLACK harness kit wire.

6. Turn the battery switch ON .

7. Turn the AC power switch to ON to restore AC power.

Battery Wiring

Red Wire

Black Wire

Jumper (White Wire)

from K41-0102-000

Red wire from

battery harness

33AH, HD Gates

K41-0102-000

Black wire

from battery

harness 33AH,

HD Gates

K41-0102-000

INSTALLATION

Summary of content (6 pages)

PAGE 1
INSTALLATION Step 6 Connect Batteries 7AH Batteries Jumper Red Wire Black Wire The batteries are charged in the circuit by the integrated transformer. 1. Turn the AC power switch to OFF. 2. Turn the battery switch OFF . 3. Connect a jumper between the positive(+) terminal of the battery to the negative terminal(-) of the other battery. 4. Connect the red battery wire from the operator to the positive(+) terminal of the battery. 5.
PAGE 2
INSTALLATION Step 7 Dual gate setup-Wireless There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Do not use wired and wireless communication simultaneously. Use only the same operator models in a dual gate setup. Wired dual gate applications will have a longer battery standby time than wireless applications. Wireless setup To activate the wireless feature: 1. Choose an operator to be the network primary operator.
PAGE 3
INSTALLATION Wired setup DUAL GATE WIRE TYPE (SHIELDED TWISTED PAIR CABLE) 22AWG up to 200 feet (61 m) 18AWG - 200-1000 feet (61-305 m) Wire must be rated at 30 Volt minimum Use only the same operator models in a dual gate setup. Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables. 1. Disconnect ALL power to the operator and turn OFF the battery and AC power switches. 2. Trench across driveway to bury the shielded twisted pair cable. 3.
PAGE 4
INSTALLATION Step 8 Close and Secure the Door Before securing the door, follow the instructions in the Adjustment section to adjust the limits, speed, and force. 1. Close the door. 2. Turn both latches 90 degrees. Step 9 Install Warning Signs Installers MUST install the UL required warning signs. The signs MUST be installed in plain view on both sides of each gate installed. Use the fastening holes in each corner to permanently secure the sign.
PAGE 5
ADJUSTMENT Limit, Speed, and Force Adjustment To reduce the risk of SEVERE INJURY or DEATH: • Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a moving gate. • Too much force on gate will interfere with proper operation of safety reversal system. • NEVER increase force beyond minimum amount required to move gate. • NEVER use force adjustments to compensate for a binding or sticking gate.
PAGE 6
ADJUSTMENT Speed Control The SPEED CONTROL dial controls the speed of the operator. The dial is preset to minimum from the factory. Set the speed as low as possible for the intended application. Gate operating speed: 0.5 ft./sec. - 1 ft./sec. For dual gate setup, set the SPEED CONTROL dial on each operator to the same setting or make sure the gate that travels further is set faster than the other operator for the smoothest operation. After any speed adjustment: 1.