Users Manual Part 5

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

LiftMaster Internet Gateway

(notprovided)

To program the operator to the LiftMaster Internet Gateway:

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the

router.

2. Connect power to the LiftMaster Internet Gateway.

3. Download the myQ

App.

4. Set up an account and follow the app instructions to add your gate

operator.

5. The LiftMaster Internet Gateway will pair to the operator if it is within

range and the operator will beep if programming is successful.

The gate operator can then be controlled through the myQ

App.

To erase the gateway:

1. Press and release the LEARN button on either operator. The green

XMITTER LED will light.

2. Press and release the LEARN button again on the same operator. The

yellow NETWORK LED will light.

3. Press and hold the LEARN button for 5 seconds. The yellow

NETWORK LED will blink (operator will beep) then turn off indicating

devices have been successfully erased.

CAPXLV Connected Access Portal

The CAPXLV can communicate wirelessly to LiftMaster

UL325 2016 gate

operators to send open commands, monitor gate position, and send email

notifications if an error occurs in the operator (email notifications are

configured in myQ

Business™). Up to 8 gate operators can be paired with

the CAPXLV - one for each primary and auxiliary relay. If using dual gates,

program the CAPXLV to the primary operator.

To Program the CAPXLV:

1. Enter Admin Mode - Flip dipswitch #1 to the ON position to enter

Admin Mode. NOTE: For new installations press the login button

without entering information in the Admin Username and Admin

Password fields.

CAPXLV

2. Select Outputs and Relay - Select the Outputs tab. Then select the

desired relay on the left-hand side (1 through 4).

3. Press LEARN button on gate operator - Press and release the LEARN

button on the primary operator. The green XMITTER LED will light.

NOTE: The operator will time out of programming mode after 180

seconds.

4. Press LEARN button on gate operator again - Press and release the

LEARN button again on the primary operator. The yellow NETWORK

LED will light.

5. Select LEARN on display - Select the LEARN button on the display and

the Learn button will go from blue to red. The gate operator and the

CAPXL will beep once and the NETWORK LED on the gate operator will

turn off indicating programming is successful. NOTE: 4 beeps/blinks

indicate you are not programming to the primary operator. Reattempt

programming from the other operator.

PROGRAMMING

Summary of content (5 pages)

PAGE 1
PROGRAMMING LiftMaster Internet Gateway (not provided) To program the operator to the LiftMaster Internet Gateway: 1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router. 2. Connect power to the LiftMaster Internet Gateway. 3. Download the myQ® App. 4. Set up an account and follow the app instructions to add your gate operator. 5. The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful.
PAGE 2
PROGRAMMING 6. Validate - Validate functionality by selecting Test Relay on the CAPXLV display. Gate Hold Open Feature The gate hold open feature will disable the timer and keep the gate at the open limit. The gate hold open feature can be activated with the reset button, see page 29 or on the KPW5 and KPW250 keypads (not provided). To use the gate hold open feature on a keypad: 1. Enter a valid 4-digit PIN when the gate is at the open limit and the timer is running 2.
PAGE 3
OPERATION Gate Operator Setup Examples The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices.
PAGE 4
OPERATOR OVERVIEW Control Board Overview 1 SET OPEN Button: The SET OPEN button sets the OPEN limit. See Adjustment section. 2 SET CLOSE Button: The SET CLOSE button sets the CLOSE limit. See Adjustment section. 3 DIAGNOSTICS Display: The diagnostics display will show the operator type, firmware version, and codes. he operator type will display as "IH" for heavy and "IN" for light, followed by a "24" which indicates the operator type as IHSL24UL/ INSL24UL.
PAGE 5
OPERATOR OVERVIEW Manual Disconnect Manual Release Handle 1. Open the cabinet door. 2. Locate the black T-shaped manual release handle attached to the gearbox in the bottom of the cabinet. 3. Pull firmly until it latches into place. To resume normal function, push the plate down to release the handle and re-engage the motor and the gearbox. Reset Button The reset button has the following functions: • Press the reset button to stop a moving gate during a normal open/close cycle, like a stop button.