Users Manual Part 7

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

Wire the Solar Panels and Batteries

20W min. - 60Wmax. for solar applications.

NOTE: 33AH batteries are strongly recommended for optimal solar

performance.

1. Connect (+) wire from solar panels to (+) pin on CHARGE IN

connector on control board.

2. Connect (-) wire from solar panels to (-) pin on CHARGE IN

connector on Control board.

3. Set the WALL XFMR/SOLAR switch to SOLAR.

10W 10W

40W APPLICATION IN SERIES

10W 10W

20W 20W

60W APPLICATION IN SERIES

10W 10W

20W 20W

20W APPLICATION IN SERIES

Battery Wiring

Control Board

Red Wire

Black Wire

Jumper (White Wire)

from K41-0102-000

Red wire from

battery harness

33AH, HD Gates

K41-0102-000

Black wire

from battery

harness 33AH,

HD Gates

K41-0102-000

33AH Batteries

Set Switch to SOLAR

SOLAR PANELS

Summary of content (7 pages)

PAGE 1
SOLAR PANELS Wire the Solar Panels and Batteries 20W min. - 60W max. for solar applications. NOTE: 33AH batteries are strongly recommended for optimal solar performance. 1. Connect (+) wire from solar panels to (+) pin on CHARGE IN connector on control board. 2. Connect (-) wire from solar panels to (-) pin on CHARGE IN connector on Control board. 3. Set the WALL XFMR/SOLAR switch to SOLAR.
PAGE 2
REPAIR PARTS Control Board K41-0073-000 BLDC Motor Drive Board IHSL24UL - K41-0245-000 INSL24UL - K41-0244-000 Idler Sprocket (QTY 2) IHSL24UL - K41-0240-000 INSL24UL - K41-0239-000 Transformer IHSL24UL - K41-0241-000 INSL24UL - K41-0346-000 Limit System IHSL24UL, INSL24UL - K41-0247-000 Alarm IHSL24UL, INSL24UL - K41-0248-000 EMI Board K1D7078 Relay Adapter Board K41-0072-000 Bridge Rectifier K41-0083-000 Output Sprocket IHSL24UL - K41-0243-000 INSL24UL - K41-0242-000 Expansion Board K1D8387-1CC B
PAGE 3
ACCESSORIES Entrapment Protection LiftMaster monitored through beam photoelectric sensor Model LMTBUL Remote Controls LiftMaster offers a variety of LiftMaster remote controls to satisfy your application needs. Single-button to 4-button, visor or key chain. The following remote controls are compatible with operators manufactured by LiftMaster after 1993. Contact your authorized LiftMaster dealer for additional details and options.
PAGE 4
ACCESSORIES Miscellaneous Long range RFID reader Model LMSC1000 Remote antenna extension kit The remote antenna extension kit allows the antenna to be remotely installed. Model 86LM LiftMaster® Internet Gateway Internet enabled accessory which connects your gate operator to your WiFi network and allows you to monitor and control gate operators and lighting accessories enabled by myQ® technology. Model 828LM Plug-in loop detector Low power. Conveniently plugs into existing control board.
PAGE 5
WARRANTY LiftMaster 5 Year Limited Commercial Warranty LiftMaster (“Seller”) warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of 5 year commercial installation from the date of purchase [and that the INSL24UL and IHSL24UL is free from defect in materials and/or workmanship for a period of 5 year commercial installation from the date of purchase].
PAGE 6
APPENDIX SAMS Wiring with Relays Not Energized SAMS Operation To keep vehicles from rushing the gate, the barrier arm stays in closed position until the gate reaches fully open position then the barrier arm is released to open and allow vehicles to pass. Control Board AUX Relay 1 Dual Gate Settings NOTE: We recommend that all accessories, except entrapment protection devices, and board configurations are set on the primary operator.
PAGE 7
APPENDIX Manual Adjustments with a Remote Control To set the limits using a remote control, first you will need a 3-button remote control that has been programmed for OPEN, CLOSE, and STOP. Refer to the Programming section. Initial Limits and Force Adjustment Adjust the limits For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force. Ensure the gate is closed. 1.